Arva Neo User manual

INITIAL START UP

NEO

Performance and user friendly

> PROBING

Cautiously probe while

going further from the

pinpoint position. Always

probe with a 90° angle

to the slope.

> SHOVELING

Studies show that excavation is the most time

consuming portion of most avalanche rescues.

Shoveling is an

important point of the

rescue process and you

need to organize it

properly. The V digging

process is an efficient

way to optimize this part

of the rescue. As soon

as you reach the buried

victim, his transceiver

has to be shut off right

away.

90°

SPEAKER

ON/OFF

> MULTIPLE VICTIMS

MULTIPLE VICTIMS

INDICATED

Victims appears on the left

part of your screen. When

a victim is marked a flag

appears close to it. The +

indicate that there is more

than 4 victims.

MARKING

Less than 3 m of a victim the pictogram is

flashing at the bottom left of the screen.

Pressing the center button and erase the mark

you victim. The camera then searches the next

victim, without returning to a marked victim.

MARKING

FUNCTION

BUTTON

ISSUE /

RESEARCH

GROUP CHECK WITH

FREQUENCY CONTROL

During startup the Neo will propose a group

check by displaying CH. If you press the

central button , the beacon swith to a

group check mode to test your partners beacons.

Your beacon will only beep when another beacon

is emetting within a 1m radius. If the tested beacon

is out of range, the information will appear on your

screen.

AVAILABLE DEVICE 5 YEAR WARRANTY

R&TTE Declarations of Conformity

Hereby. Name of manufacturer: AsteelFlash France. Adress: 43, rue du Vieux Chêne.

Zip Code: 38240. City: Meylan. Country: France. Declares that the avalanche beacon.

Type designation: NEO. Trademark: ARVA, is in compliance with the essential

requirements and other relevant provisions of directive. 1999/5/EC. The compliance

of the device has been evaluated according to the Electromagnetic compatibility

standard test: FCC CFR 47 part 15, Subpart C. The complete declaration of

conformity is available at the address above. Name: TORRES. Fonction: Establish-

ment Development Director. Date: 19/08/2011. Signature:

FCC requirements: - FCC ID: O9BARVANEO

NOTE: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful inter-

ference in a residential installation. This

equipment generates uses and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in

a particular installation. If this equipment

does cause harmful interference to radio or

television reception which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct interference

by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet on

circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/

TV technician for help.

- Information to user: Changes or modiﬁ-

cations not expressly approved by the party

responsible for compliance could void the

user’s authority to operate the equipment.

> TECHNICAL DATA

• 100% digital

• 3 antennas

• User frendly

• Distance and direction

indicator

• Marking function for

multiple burialssituations

• Multiple victims icon

(1, 2 or 3 and more)

• Automatic switch back to

transmit mode with timer

• 60 m search band width

• Weight: 240 g

• Battery life: more than

250 Hours (Emitting)

• Requires 3 alkaline

batteries AAA/LR03

WARNING: THERE’S A RISK OF BURST IF THE BATTERY IS

THROWN IN FIRE OF IF IT IS EXCHANGED WITH AN INCORRECT

TYPE ONE. THROW AWAY USED BATTERIES IN ACCORDANCE

TO INSTRUCTIONS. IMPORTANT SWITZERLAND: THE 4.10

ANNEX OF THE SR 814.013 NORM IS RELEVANT TO BATTERIES.

Elimination of manufacturing wastes by the private users in the

eu. This symbol written in the product or in its packaging

indicates that this product must not be throw in the garbage

with your other waste. Its your responsability to rid of your

manufacturing wastes bringing it to a specialized sorting oﬀice

for the recycling of electrical and electronic instruments. Collection

and recycling separated of your wastes will contribute to preserve natural

resources and guarantee a recycling respectful of the environment and human

health. For further information concerning the recycling center near your

place of residence, contact your town hall, the elimination service of garbage

heap or the store where you bought the instrument.

Bandwidth Antennas Dual

frequency Multiple

burried

indication

Bandwidth

Antennas

Dual

frequency Multiple

burried

indication

Bandwidth Antennas Dual

frequency Multiple

burried

indication

Bandwidth Antennas Dual

frequency

Multiple

burried

indication

Erasing

function

Scrolling

& marking

function

Updatable

Marking

function Automatic

switch back

to transmit

Bandwidth

MENU CONFIGURATION

(Experienced users)

With the beacon switched off, go into the search

mode by sliding grey search button up, then while

holding the center button turn beacon on with

the toggle button. The only button used to manage

the menu is the central one .

short

push

Select with a long push, chose

option with shorts pushes

0 = No Auto-revert

2/4/8 = Select between

2/4/8 minutes

Auto-revert

(to trAnsmit)

LonG

push LonG

push

short

push

Select with a long push, chose

option with shorts pushes

3 = Marking below 3 m of the victim

5 = Marking below 5 m of the victim

3LonG

push LonG

push

mArKinG

Select with a long push, chose

option with shorts pushes

0 = Group Check OFF

1 = Group Check ON

LonG

push LonG

push

short

push

Group checK

END

LonG

push

enD

end

short push

CDF13NGB

> PRIMARY SEARCH

Walk through the avalanche, searching a signal,

following to one of the two drawings.

Optimize your ARVA range

Keep your beacon parallel

to the slope at all times.

The beacon can be rotated

on an axis to try to catch

any signal.

> SECONDARY SEARCH

Once a signal is received begin secondary search:

• Stay focused on the information displayed on

the screen (distance, direction).

• Point the device to the signal direction.

• Stay calm

• Slow down while you are getting

closer to the victim.

• If the distance decreases, you are

searching in the right direction. If

you are going in the wrong direction,

the U-turn alert will appear on your screen. Turn

around and check that the figures are now decreasing.

• Also look at the scene for any visible signs

(like a glove or pole out of the snow)

• If you have difficulties in a complex, multiple

victim situation, quickly walk back and approach

from another direction.

60m

30m

60m

www.arva-equipment.com

> FINAL SEARCH

When within three meters your beacon will not

display a direction arrow, to pinpoint signal use the

cross or orthogonal search to find the closest signal.

1. The transceiver

must be at the level of

the snow, parallel to it.

2. Move your Arva

only in straight line,

and change direction

only at 90°, to locate

the place where the

distance is the smaller.

Proceed to probing as soon as you find the likely

buried position at less than one meter.

First sampling

point where the

distance shown

is the lowest.

Pinpoint search

track example

> INITIAL START UP

FITTING BATTERIES AND ADVICE

The ARVA NEO only operates with 3 standard AAA/LR03

alkaline batteries. Open the battery compartment cover

with a screwdriver or coin. The 3 batteries must always

be of the same brand and replaced at the same time.

We advice to replace the batteries if the power level is

under 50%.

NEVER USE RECHARGEABLE OR LITHIUM BATTERIES.

These do not resist cold and/or discharge in one go

(unlike alkaline batteries, which discharge gradually).

Remove the batteries if the device is left unused for a

long time (especially in summer). If batteries leak, the

warranty does not apply.

STICKER FOR AFTER SALE PROCEDURE

A sticker with the unique ID and warranty date of your

device is located in the batteries compartment.

YOU MUST NOT REMOVE THIS STICKER WHICH IS

ESSENTIAL FOR AFTER SALE PROCEDURE.

> INITIAL START UP

1. To switch on your

device, plug in the T

rounded button and

turn 1/4 turn.

2. insert your device into the holster (screen facing

your body) and close the holster buckle.

3. Put the black strap

around your head and over

the left shoulder. Adjust

to the correct length.

4. Put the red straps

around your waist and

adjust it.

DEVICE CARRYING

The holster must always be worn against your inner

layer of clothing (underwear or next to skin). The ARVA

should preferably by covered by a garment to prevent

cold and impacts.

> SEARCH MODE

In avalanche situation, to switch in search mode,

open the holster and take off the device which will

stay attached by the elastic leash and the black strap.

To switch in search

mode, push the grey

side button up.

> PRIMARY SEARCH

Walk through the avalanche, searching a signal,

following to one of the two drawings.

Optimize your ARVA range

Keep your beacon parallel

to the slope at all times.

The beacon can be rotated

on an axis to try to catch

any signal.

> SECONDARY SEARCH

Once a signal is received begin secondary search:

• Stay focused on the information displayed on

the screen (distance, direction).

• Point the device to the signal direction.

• Stay calm

• Slow down while you are getting

closer to the victim.

• If the distance decreases, you are

searching in the right direction. If

you are going in the wrong direction,

the U-turn alert will appear on your screen. Turn

around and check that the figures are now decreasing.

• Also look at the scene for any visible signs

(like a glove or pole out of the snow)

• If you have difficulties in a complex, multiple

victim situation, quickly walk back and approach

from another direction.

60m

30m

60m

www.arva-equipment.com

> FINAL SEARCH

When within three meters your beacon will not

display a direction arrow, to pinpoint signal use the

cross or orthogonal search to find the closest signal.

1. The transceiver

must be at the level of

the snow, parallel to it.

2. Move your Arva

only in straight line,

and change direction

only at 90°, to locate

the place where the

distance is the smaller.

Proceed to probing as soon as you find the likely

buried position at less than one meter.

First sampling

point where the

distance shown

is the lowest.

Pinpoint search

track example

> INITIAL START UP

FITTING BATTERIES AND ADVICE

The ARVA NEO only operates with 3 standard AAA/LR03

alkaline batteries. Open the battery compartment cover

with a screwdriver or coin. The 3 batteries must always

be of the same brand and replaced at the same time.

We advice to replace the batteries if the power level is

under 50%.

NEVER USE RECHARGEABLE OR LITHIUM BATTERIES.

These do not resist cold and/or discharge in one go

(unlike alkaline batteries, which discharge gradually).

Remove the batteries if the device is left unused for a

long time (especially in summer). If batteries leak, the

warranty does not apply.

STICKER FOR AFTER SALE PROCEDURE

A sticker with the unique ID and warranty date of your

device is located in the batteries compartment.

YOU MUST NOT REMOVE THIS STICKER WHICH IS

ESSENTIAL FOR AFTER SALE PROCEDURE.

> INITIAL START UP

1. To switch on your

device, plug in the T

rounded button and

turn 1/4 turn.

2. insert your device into the holster (screen facing

your body) and close the holster buckle.

3. Put the black strap

around your head and over

the left shoulder. Adjust

to the correct length.

4. Put the red straps

around your waist and

adjust it.

DEVICE CARRYING

The holster must always be worn against your inner

layer of clothing (underwear or next to skin). The ARVA

should preferably by covered by a garment to prevent

cold and impacts.

> SEARCH MODE

In avalanche situation, to switch in search mode,

open the holster and take off the device which will

stay attached by the elastic leash and the black strap.

To switch in search

mode, push the grey

side button up.

> PRIMARY SEARCH

Walk through the avalanche, searching a signal,

following to one of the two drawings.

Optimize your ARVA range

Keep your beacon parallel

to the slope at all times.

The beacon can be rotated

on an axis to try to catch

any signal.

> SECONDARY SEARCH

Once a signal is received begin secondary search:

• Stay focused on the information displayed on

the screen (distance, direction).

• Point the device to the signal direction.

• Stay calm

• Slow down while you are getting

closer to the victim.

• If the distance decreases, you are

searching in the right direction. If

you are going in the wrong direction,

the U-turn alert will appear on your screen. Turn

around and check that the figures are now decreasing.

• Also look at the scene for any visible signs

(like a glove or pole out of the snow)

• If you have difficulties in a complex, multiple

victim situation, quickly walk back and approach

from another direction.

60m

30m

60m

www.arva-equipment.com

> FINAL SEARCH

When within three meters your beacon will not

display a direction arrow, to pinpoint signal use the

cross or orthogonal search to find the closest signal.

1. The transceiver

must be at the level of

the snow, parallel to it.

2. Move your Arva

only in straight line,

and change direction

only at 90°, to locate

the place where the

distance is the smaller.

Proceed to probing as soon as you find the likely

buried position at less than one meter.

First sampling

point where the

distance shown

is the lowest.

Pinpoint search

track example

> INITIAL START UP

FITTING BATTERIES AND ADVICE

The ARVA NEO only operates with 3 standard AAA/LR03

alkaline batteries. Open the battery compartment cover

with a screwdriver or coin. The 3 batteries must always

be of the same brand and replaced at the same time.

We advice to replace the batteries if the power level is

under 50%.

NEVER USE RECHARGEABLE OR LITHIUM BATTERIES.

These do not resist cold and/or discharge in one go

(unlike alkaline batteries, which discharge gradually).

Remove the batteries if the device is left unused for a

long time (especially in summer). If batteries leak, the

warranty does not apply.

STICKER FOR AFTER SALE PROCEDURE

A sticker with the unique ID and warranty date of your

device is located in the batteries compartment.

YOU MUST NOT REMOVE THIS STICKER WHICH IS

ESSENTIAL FOR AFTER SALE PROCEDURE.

> INITIAL START UP

1. To switch on your

device, plug in the T

rounded button and

turn 1/4 turn.

2. insert your device into the holster (screen facing

your body) and close the holster buckle.

3. Put the black strap

around your head and over

the left shoulder. Adjust

to the correct length.

4. Put the red straps

around your waist and

adjust it.

DEVICE CARRYING

The holster must always be worn against your inner

layer of clothing (underwear or next to skin). The ARVA

should preferably by covered by a garment to prevent

cold and impacts.

> SEARCH MODE

In avalanche situation, to switch in search mode,

open the holster and take off the device which will

stay attached by the elastic leash and the black strap.

To switch in search

mode, push the grey

side button up.

> PRIMARY SEARCH

Walk through the avalanche, searching a signal,

following to one of the two drawings.

Optimize your ARVA range

Keep your beacon parallel

to the slope at all times.

The beacon can be rotated

on an axis to try to catch

any signal.

> SECONDARY SEARCH

Once a signal is received begin secondary search:

• Stay focused on the information displayed on

the screen (distance, direction).

• Point the device to the signal direction.

• Stay calm

• Slow down while you are getting

closer to the victim.

• If the distance decreases, you are

searching in the right direction. If

you are going in the wrong direction,

the U-turn alert will appear on your screen. Turn

around and check that the figures are now decreasing.

• Also look at the scene for any visible signs

(like a glove or pole out of the snow)

• If you have difficulties in a complex, multiple

victim situation, quickly walk back and approach

from another direction.

60m

30m

60m

www.arva-equipment.com

> FINAL SEARCH

When within three meters your beacon will not

display a direction arrow, to pinpoint signal use the

cross or orthogonal search to find the closest signal.

1. The transceiver

must be at the level of

the snow, parallel to it.

2. Move your Arva

only in straight line,

and change direction

only at 90°, to locate

the place where the

distance is the smaller.

Proceed to probing as soon as you find the likely

buried position at less than one meter.

First sampling

point where the

distance shown

is the lowest.

Pinpoint search

track example

> INITIAL START UP

FITTING BATTERIES AND ADVICE

The ARVA NEO only operates with 3 standard AAA/LR03

alkaline batteries. Open the battery compartment cover

with a screwdriver or coin. The 3 batteries must always

be of the same brand and replaced at the same time.

We advice to replace the batteries if the power level is

under 50%.

NEVER USE RECHARGEABLE OR LITHIUM BATTERIES.

These do not resist cold and/or discharge in one go

(unlike alkaline batteries, which discharge gradually).

Remove the batteries if the device is left unused for a

long time (especially in summer). If batteries leak, the

warranty does not apply.

STICKER FOR AFTER SALE PROCEDURE

A sticker with the unique ID and warranty date of your

device is located in the batteries compartment.

YOU MUST NOT REMOVE THIS STICKER WHICH IS

ESSENTIAL FOR AFTER SALE PROCEDURE.

> INITIAL START UP

1. To switch on your

device, plug in the T

rounded button and

turn 1/4 turn.

2. insert your device into the holster (screen facing

your body) and close the holster buckle.

3. Put the black strap

around your head and over

the left shoulder. Adjust

to the correct length.

4. Put the red straps

around your waist and

adjust it.

DEVICE CARRYING

The holster must always be worn against your inner

layer of clothing (underwear or next to skin). The ARVA

should preferably by covered by a garment to prevent

cold and impacts.

> SEARCH MODE

In avalanche situation, to switch in search mode,

open the holster and take off the device which will

stay attached by the elastic leash and the black strap.

To switch in search

mode, push the grey

side button up.

> PRIMARY SEARCH

Walk through the avalanche, searching a signal,

following to one of the two drawings.

Optimize your ARVA range

Keep your beacon parallel

to the slope at all times.

The beacon can be rotated

on an axis to try to catch

any signal.

> SECONDARY SEARCH

Once a signal is received begin secondary search:

• Stay focused on the information displayed on

the screen (distance, direction).

• Point the device to the signal direction.

• Stay calm

• Slow down while you are getting

closer to the victim.

• If the distance decreases, you are

searching in the right direction. If

you are going in the wrong direction,

the U-turn alert will appear on your screen. Turn

around and check that the figures are now decreasing.

• Also look at the scene for any visible signs

(like a glove or pole out of the snow)

• If you have difficulties in a complex, multiple

victim situation, quickly walk back and approach

from another direction.

60m

30m

60m

www.arva-equipment.com

> FINAL SEARCH

When within three meters your beacon will not

display a direction arrow, to pinpoint signal use the

cross or orthogonal search to find the closest signal.

1. The transceiver

must be at the level of

the snow, parallel to it.

2. Move your Arva

only in straight line,

and change direction

only at 90°, to locate

the place where the

distance is the smaller.

Proceed to probing as soon as you find the likely

buried position at less than one meter.

First sampling

point where the

distance shown

is the lowest.

Pinpoint search

track example

> INITIAL START UP

FITTING BATTERIES AND ADVICE

The ARVA NEO only operates with 3 standard AAA/LR03

alkaline batteries. Open the battery compartment cover

with a screwdriver or coin. The 3 batteries must always

be of the same brand and replaced at the same time.

We advice to replace the batteries if the power level is

under 50%.

NEVER USE RECHARGEABLE OR LITHIUM BATTERIES.

These do not resist cold and/or discharge in one go

(unlike alkaline batteries, which discharge gradually).

Remove the batteries if the device is left unused for a

long time (especially in summer). If batteries leak, the

warranty does not apply.

STICKER FOR AFTER SALE PROCEDURE

A sticker with the unique ID and warranty date of your

device is located in the batteries compartment.

YOU MUST NOT REMOVE THIS STICKER WHICH IS

ESSENTIAL FOR AFTER SALE PROCEDURE.

> INITIAL START UP

1. To switch on your

device, plug in the T

rounded button and

turn 1/4 turn.

2. insert your device into the holster (screen facing

your body) and close the holster buckle.

3. Put the black strap

around your head and over

the left shoulder. Adjust

to the correct length.

4. Put the red straps

around your waist and

adjust it.

DEVICE CARRYING

The holster must always be worn against your inner

layer of clothing (underwear or next to skin). The ARVA

should preferably by covered by a garment to prevent

cold and impacts.

> SEARCH MODE

In avalanche situation, to switch in search mode,

open the holster and take off the device which will

stay attached by the elastic leash and the black strap.

To switch in search

mode, push the grey

side button up.

> PRIMARY SEARCH

Walk through the avalanche, searching a signal,

following to one of the two drawings.

Optimize your ARVA range

Keep your beacon parallel

to the slope at all times.

The beacon can be rotated

on an axis to try to catch

any signal.

> SECONDARY SEARCH

Once a signal is received begin secondary search:

• Stay focused on the information displayed on

the screen (distance, direction).

• Point the device to the signal direction.

• Stay calm

• Slow down while you are getting

closer to the victim.

• If the distance decreases, you are

searching in the right direction. If

you are going in the wrong direction,

the U-turn alert will appear on your screen. Turn

around and check that the figures are now decreasing.

• Also look at the scene for any visible signs

(like a glove or pole out of the snow)

• If you have difficulties in a complex, multiple

victim situation, quickly walk back and approach

from another direction.

60m

30m

60m

www.arva-equipment.com

> FINAL SEARCH

When within three meters your beacon will not

display a direction arrow, to pinpoint signal use the

cross or orthogonal search to find the closest signal.

1. The transceiver

must be at the level of

the snow, parallel to it.

2. Move your Arva

only in straight line,

and change direction

only at 90°, to locate

the place where the

distance is the smaller.

Proceed to probing as soon as you find the likely

buried position at less than one meter.

First sampling

point where the

distance shown

is the lowest.

Pinpoint search

track example

> INITIAL START UP

FITTING BATTERIES AND ADVICE

The ARVA NEO only operates with 3 standard AAA/LR03

alkaline batteries. Open the battery compartment cover

with a screwdriver or coin. The 3 batteries must always

be of the same brand and replaced at the same time.

We advice to replace the batteries if the power level is

under 50%.

NEVER USE RECHARGEABLE OR LITHIUM BATTERIES.

These do not resist cold and/or discharge in one go

(unlike alkaline batteries, which discharge gradually).

Remove the batteries if the device is left unused for a

long time (especially in summer). If batteries leak, the

warranty does not apply.

STICKER FOR AFTER SALE PROCEDURE

A sticker with the unique ID and warranty date of your

device is located in the batteries compartment.

YOU MUST NOT REMOVE THIS STICKER WHICH IS

ESSENTIAL FOR AFTER SALE PROCEDURE.

> INITIAL START UP

1. To switch on your

device, plug in the T

rounded button and

turn 1/4 turn.

2. insert your device into the holster (screen facing

your body) and close the holster buckle.

3. Put the black strap

around your head and over

the left shoulder. Adjust

to the correct length.

4. Put the red straps

around your waist and

adjust it.

DEVICE CARRYING

The holster must always be worn against your inner

layer of clothing (underwear or next to skin). The ARVA

should preferably by covered by a garment to prevent

cold and impacts.

> SEARCH MODE

In avalanche situation, to switch in search mode,

open the holster and take off the device which will

stay attached by the elastic leash and the black strap.

To switch in search

mode, push the grey

side button up.