ASI FS-0300 User manual

FOR MODEL № FS-0300
HAND SANITIZER DISPENSER STAND ASSEMBLY INSTRUCTIONS
AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, Yonkers, NY 10701 [phone] • [phone] www.americanspecialties.com
043020103520 04APR20
A
1. ASSEMBLY:
1.1 Lock post to base with one (1) split helical lock washer (supplied) and 5/16" -18 x 1" hex bolt (supplied)
using a 1/2" [13] wrench (by others), as shown on detail A
2.2 Unit should be placed in location to maximize access by pedestrian traffic and to not interfere with any ac-
cessible route clearances.
2. STEPS TO INSTALL 20364 AND 20365
2.1 Secure dispenser (supplied separately) to the stand mounting plate (factory installed) with four (4) screw-posts
(supplied) through concealed mounting holes in the dispenser back (see Detail B and Detail C)
2.2 Use two (2) #2 Philips bit screw drivers (by others) into binding barrels (supplied) inserted from behind the
mounting plate (see detail C).
2.3 Follow detailed Set-up instructions & provided in dispenser Owner Manual (OM) provided with dispenser.
2.4 When assembly is completed no fasteners are visible on exposed dispenser surfaces.
BASE
POST
HEX BOLT (SUPPLIED)
SPLIT LOCK WASHER
(SUPPLIED)
1/2" [13] WRENCH
(BY OTHERS)
DETAIL A
BINDING BARREL AND
SCREW SUPPLIED
LOOSE IN KIT
QTY = 4
PHILIPS SCREW
DRIVER (BY OTHERS)
PHILIPS SCREW
DRIVER (BY OTHERS)
BINDING BARREL
AND SCREW
(SUPPLIED)
TYPICAL OF FOUR (4)
PHILIPS SCREW DRIVER
(BY OTHERS)
SCREW (SUPPLIED)
TYPICAL OF FOUR (4)
BINDING BARREL (SUPPLIED)
TYPICAL OF FOUR (4)
PHILIPS SCREW DRIVER
(BY OTHERS)
BDISPENSER SUPPLIED SEPARATELY.
MODEL N° 20364 DISPENSER SHOWN FOR REF ONLY.
MODEL N° 20365 SIMILAR
DETAIL B
C
DETAIL C
DISPENSER SUPPLIED SEPARATELY.
MODEL N° 20364 DISPENSER SHOWN FOR REF ONLY.
MODEL N° 20365 SIMILAR

FOR MODEL № FS-0300
HAND SANITIZER DISPENSER STAND ASSEMBLY INSTRUCTIONS
AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, Yonkers, NY 10701 [phone] • [phone] www.americanspecialties.com
043020103520 04APR20
0361-SUGESTED LOCATION FOR TAPE INSTALLATION
2. STEPS TO INSTALL 0361
2.1 Clean dispenser back with Isopropyl Alcohol. Allow to dry completely.
2.2 Cut the 16" double sided tape (supplied) into two (2) lengths of 7-7/8" [200] as shown on diagram.
2.3 Adhere tape strips per diagram with no wrinkles or air bubbles, with liners in place, press to ensure even attachment.
2.4 Clean HSDS mounting plate with Isopropyl Alcohol. Allow to dry completely.
2.5 Mark alignment guidelines on HSDS mounting plate (or use blue painters tape, by others) for dispenser outline.
2.6 Remove liner strips from tapes.
2.7 While aligning dispenser straight with marked lines press evenly and maintain pressure for 1 hour before using.
ALIGN W/ SLOT OPENING
DOUBLE SIDED TAPE
ALIGN W/ BOTTOM
D
E
DETAIL D
1" [25,4] REF
3/64" [1,2]
8"
[203]
1-3/32" [27,7]
46-3/8"
[1178]
RECOMMENDED
HEIGHT INSTALLATION
DETAIL E
DISPENSER SUPPLIED SEPARATELY.
MODEL N° 0361 DISPENSER SHOWN FOR REF ONLY.

FOR MODEL № FS-0300
HAND SANITIZER DISPENSER STAND ASSEMBLY INSTRUCTIONS
AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, Yonkers, NY 10701 [phone] • [phone] www.americanspecialties.com
0362-SUGESTED LOCATION FOR TAPE INSTALLATION
043020103520 04APR20
2. STEPS TO INSTALL 0362
2.1 Clean dispenser back with Isopropyl Alcohol. Allow to dry completely.
2.2 Cut the 16" double sided tape (supplied) into two (2) lengths of 8" [203] as shown on diagram.
2.3 Adhere tape strips per diagram with no wrinkles or air bubbles, with liners in place, press to ensure even attachment.
2.4 Clean HSDS mounting plate with Isopropyl Alcohol. Allow to dry completely.
2.5 Mark alignment guidelines on HSDS mounting plate (or use blue painters tape, by others) for dispenser outline.
2.6 Remove liner strips from tapes.
2.7 While aligning dispenser straight with marked lines press evenly and maintain pressure for 1 hour before using.
DETAIL F
ALIGN W/ SLOT OPENING
DOUBLE SIDED TAPE
F
1" [25,4] REF
8"
[203]
1/2"
[12,7]
46-1/4"
[1175]
RECOMMENDED
HEIGHT INSTALLATION
DISPENSER SUPPLIED SEPARATELY.
MODEL N° 0362 DISPENSER SHOWN FOR REF ONLY.

FOR MODEL № FS-0300
HAND SANITIZER DISPENSER STAND ASSEMBLY INSTRUCTIONS
AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, Yonkers, NY 10701 [phone] • [phone] www.americanspecialties.com
0501-1-SUGESTED LOCATION FOR TAPE INSTALLATION
043020103520 04APR20
2. STEPS TO INSTALL 0501-1
2.1 Clean dispenser back with Isopropyl Alcohol. Allow to dry completely.
2.2 Cut the 16" double sided tape (supplied) into two (2) lengths of 7-7/8" [200] as shown on diagram.
2.3 Adhere tape strips per diagram with no wrinkles or air bubbles, with liners in place, press to ensure even attachment.
2.4 Clean HSDS mounting plate with Isopropyl Alcohol. Allow to dry completely.
2.5 Remove liner strips from tapes.
2.6 Aligning dispenser straight, press evenly and maintain pressure for 1 hour before using.
47-51/64"
[951]
DISPENSER SUPPLIED SEPARATELY.
MODEL N° 0501-1 DISPENSER SHOWN FOR REF ONLY.
5/8''
[16]
3/4" [19]
7-7/8''
[200]
1''
[25,4]
REF
1''
[25]
1/8 [3,2]
3'' [76]