4
ASO GmbH Antriebs- und Steuerungstechnik Hansastraße 52 59557 Lippstadt GERMANY
T
el.: +49 294
1 9
793-0
Fax: +49 294
1 9
793 299
www.asosafety.de
E-Mail:
[email protected]ELMON wicom 81-463
Quick Guide
20.11.2020
DOC0000115 Rev: 01
Pairing
LED
Receiver
1. Press and release
the teach-in button
shortly
Receiver
2. Blue LED „IND“
starts fl ashing slowly
(1/s) for 25s
Transmitter
3. Press and release
the teach-in button
shortly
further Transmitter
4. optional:
Press and release the
teach-in button shortly
Transmitter
LED
5. Blue LED „IND“
fl ashes quickly
(4/s) for 2s
Transmitter /
Receiver
6. Connection(s)
successful
Receiver
7. Press the teach-in
button shortly to exit
the learning mode
Receiver
LED
8. Blue LED „IND“
fl ashes quickly
(4/s) for 2s
LED
Transmitter
1. Press teach-in
button for at least 2s
Transmitter /
Receiver
2. Blue LED „IND“
fl ashes quickly
(8/s) for 2s
Transmitter /
Receiver
3. The transmitter /
receiver is reseted
Factory setting
LED Guide Transmitter
LED Colour Condition Description
IND Blue
Blinking (1/s) for 25 s – Pushing teach-in button once after a factory reset confi rmed Teach-in sequence initiated
Permanently on for 2 s – Pushing teach-in button once Transmitter is connected or waiting for a connection
Blinking (2/s) – while holding the teach-in button more than 2 s Initiating Factory reset
Blinking (8/s) for 2 s – after pressing and holding the teach-in button Factory reset confi rmed
LED Guide Receiver
LED Colour Condition Description
POWER Green On Receiver is powered on
Off Receiver is powered off
SL, SE2 Orange Permanently On Obstacle detected / Hardware test is failed / safe state
Blinking No obstacle / Hardware test is active
ACT Green Permanently On System is active
Blinking System is in standby mode
CON Orange
Permanently On Receiver and transmitter are connected
Blinking slow (1/s) One or more transmitter are missing or out of range
One or more transmitter report(s) low battery state
Blinking fast (4/s) Radio interferences are too high (e.g. Wi-Fi or Bluetooth)
IND Blue
Blinking fast – while not pushing the teach-in button Delay on radio connection (timeout) / One or more transmitter are missing,
out of range, blocked, interfered etc.
Blinking (1/s) for 25 s – Pushing teach-in button once after a factory reset confi rmed Teach-in sequence initiated
Permanently on for 2 s – Pushing teach-in button once Receiver is connected or waiting for a connection
Blinking (2/s) – while holding the teach-in button more than 2 s Initiating Factory reset
Blinking (8/s) for 2 s – after pressing and holding the teach-in button Factory reset confi rmed
Technical Data
Inputs 8k2
Outputs 8k2, NCC
Range 20m*
Operating voltage 10-30V DC
Reaction time 40ms
Frequency 2,4GHz
Power consumption Receiver Typ.: 18mA (24V DC)
Max. voltage (all outputs) 30V
Max. current load (all outputs) 1A
Safety properties Cat. 2 / PL „c“
(intrinsically safe)
Operation temperature -20°C to 55°C
Housing material PC
Protection type IP65
Battery life time approx. 2 years
Dimensions 130x94x60mm
* under optimal conditions
Declaration of conformity
We herby declare that the following product of the model range:
ELMON wicom 81-463
that as a result of the manner in which the product was designed, the type of construction and the pro-
duct which, as a result have been brought on the general market comply to the relevant basic health and
safety regulations of the following EC Council Directive:
prEN 12978: 2017
EN 13849-1:2016
Attention!
This document does not replace the operating instructions. For detailed
information, the operating instructions must be downloaded from our
website and used. This company is not responsible for damage or problems
resulting from misuse, incorrect installation or violation of the instructions
mentioned in the manual. https://www.asosafety.
co.uk/downloads
Receiver
1. Press teach-in
button for at least 2s
