ASROCK Rack E3C232D2I User manual

E3C236D2I / E3C232D2I
Quick Installation Guide
www.asrockrack.com
No. Description No. Description
1 USB 2.0 Ports (USB_1_2) 5 USB 3.0 Ports (USB3_1_2)
2 LAN RJ-45 Port (IPMI_LAN) 6 LAN RJ-45 Port (LAN1)
3VGA Port (VGA1) 7 USB 3.0 Ports (USB3_3_4)
4 Serial Port (COM1) 8 LAN RJ-45 Port (LAN2)
4
2
P/N: 15G065079100AK V1.0
Install the Server Board
Motherboard Layout
Jumper Cap On/O
The server board User's Manual is available for download from the ASRock Rack's ofcial website
at http://www.asrockrack.com.
Take note of the following precautions before you install server board components or change any
server board settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the server board’s components due to static electricity, NEVER place your
server board directly on the carpet or the like. Also remember to use a grounded wrist strap or
touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in the bag
that comes with the component.
5. When placing screws into the screw holes to secure the server board to the chassis, please do
not over-tighten the screws! Doing so may damage the server board.
1
1Insert the server board into the chassis.
2Af fi x the screws clockw ise into the
mounting holes in all of the corners of
the server board.
Do not over-tighten the screws
When the jumper cap is placed on the pins, the
jumper is “Short”. If no jumper cap is placed on the
pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when a jumper cap is placed on
these 2 pins.
I/O Panel
DDR4_B1 (64 bit, 288-pin module)
DDR4_A1 (64 bit, 288-pin module)
Intel
C236
PCIE7
BIOS
ROM
17.0cm (6.7 in)
17.0cm (6.7 in)
ATXPWR1
ATX12V1
CMOS
Battery
FRNT_FAN1
COM1
VGA1
56
7
8
12
13
18
19
17
15
16
21 20
22
23
24
25
RoHS
26
BMC
CPU_FAN1
LAN1
Top:
IPMI
LAN
USB 3.0
T: USB_1
B: USB_2
USB 2.0
T: USB_1
B: USB_2
NMI_BTN1
IPMB1
1
1
SPEAKER1
USB3_7
USB3_5_6
1
TPM1
REAR_FAN1
SATA_0 SATA_1 SATA_2
14
27
SATA_SGPIO2
1
E3C236D2I
LAN2
USB 3.0
T: USB_3
B: USB_4
PECI1
1
1
1
1
1
1
M2_1
NUT1
PANEL1
1
AUX_PANEL1
HDLED RESET
PLED PWRBTN
1
1
PSU_SMB1
BMC_SMB1
1
1
SATA_SGPIO1
ME_RECOVERY1
SATA_3
SATA_4
SATA_5
1
PMBUS_SEL_DAT1
PMBUS_SEL_ALT1
PMBUS_SEL_CLK1
1234
10
11
29
30
31
32
CLRMOS1
9
T 1
R
28
1
No. Description
1 CPU PECI Mode Jumper (PECI1)
2PMBUS Mode Jumper (PMBUS_SEL_ALT1)
3PMBUS Mode Jumper (PMBUS_SEL_DAT1)
4 ermal Sensor Header (TR1)
5 ATX Power Connector (ATXPWR1)
6 CPU Fan Connector (CPU_FAN1)
7 Front Fan Connector (FRNT_FAN1)
82 x 288-pin DDR4 DIMM Slots
(DDR4_A1, DDR4_B1, Blue)
9 Clear CMOS Pad (CLRMOS1)
10 SATA SGPIO Connector (SATA_SGPIO1)
11 SATA SGPIO Connector (SATA_SGPIO2)
12
E3C236D2I: Vertical Type A USB 3.0 (USB3_7)
E3C232D2I: Vertical Type A USB 2.0 (USB3_7)
13 SATA3 Connector (SATA_0)
14 SATA3 Connector (SATA_1)
15 SATA3 Connector (SATA_3)
16 SATA3 Connector (SATA_2)
17 SATA3 Connector (SATA_4)
18 SATA3 Connector (SATA_5)
19 Speaker Header (SPEAKER1)
20 M.2 Slot (M2_1)* (supports M.2 module type 2230)
21 System Panel Header (PANEL1)
22 USB 3.0 Header (USB3_5_6)
23 ATX 12V Power Connector (ATX12V1)
24 PSU SMBus (PSU_SMB1)
25 Auxiliary Panel Header (AUX_PANEL1)
26 TPM Header (TPM1)
27 Intelligent Platform Management Bus header
(IPMB1)
28 ME Recovery Jumper (ME_RECOVERY1)
29 Non Maskable Interrupt Button (NMI_BTN1)
30 BMC SMBus Header (BMC_SMB1)
31 Rear Fan Connector (REAR_FAN1)
32 PMBUS Mode Jumper (PMBUS_SEL_CLK1)
6
4
3
2
15
8
7
Note:
E3C23 6D2 I:
Intel C236
E3C232D2I:
Intel C232
(See Note)
*15G065079100AK*
3

E3C236D2I / E3C232D2I
Quick Installation Guide
www.asrockrack.com
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10M bps connection or no
link
Blinking Yellow Data Activity Yel low 100M bps connection
On Link Green 1Gbps connection
8LAN Port LED Indications
5
7
6
123
Open the socket levers and the
CPU socket cover. Remove the
CPU protection cap.
Install the processor and close
the socket cover.
Close the socket levers.
Install the CPU Fan and Heatsink
CPU_FAN
12
Apply the thermal grease. Install the
CPU fan and heatsink and secure
the screws.
Connect the CPU fan to the CPU
FAN connector.
Install the Power Cables
System Panel Auxiliary Panel
Install the Processor
10 Install the Memory
11 Headers
9Install the PCIE Card
We recommend using the CPU Installation tool to avoid CPU pin-bent problem.
A
B
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection or
no link
Blinking Yellow Data Activity Yel low 100Mbps connection
On Link Green 1Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
IPMI LAN Port
LAN Port
ACT/LINK LED
SPEED LED
LAN Port
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
GND
SMB_CLK
SMB_Alert
CASEOPEN
1
SMB_DATA
+3VSB
LAN1_LINK
LED_PWR
LAN2_LINK
LED_PWR
+5VSB
GND
GND
LOCATORLED1+
LOCATORLED1-
LOCATORBTN#
System Fault LED-
AB
CD
System Fault LED+
E
1
3V 3V
GND GND
5V 5V
GND
PWROK_PS
5VSB
12V 12V
3V
3V -12V GND PSON# GND GND GND 5V 5V 5V GND N/A
12
24 13
1
2
3
4
GND
12V
123
Unlock a DIMM slot by
pressing the module clips
outward.
Insert the memory module. Lock the clips.
M.2_SSD (NGFF) Module Installation
12
1
2
3
Prepare a M.2_SSD (NGFF) module and the screw.
Peel o the yellow protective lm on the nut to
be used. Hand tighten the stando into the nut
location on the motherboard.
Align and gently insert the M.2 (NGFF) SSD
module into the M.2 slot. Please be aware that
the M.2 (NGFF) SSD module only ts in one
orientation.
Tighten the screw with a screwdriver to secure the
module into place. Please do not overtighten the
screw as this might damage the module.
4
NUT1NUT2
NUT1
NUT1
* e M.2 socket supports M.2 module type 2230 (PCB length: 3 cm).