Assa Abloy Aperio AH20 User manual

1
Experience a safer
and more open world
Aperio®
AH20/AH30
Hub Installation Guide

2
AH20/AH30 - Table of Contents
Conforms to EN 62368-1 and UL/CSA 62368-1
AH20/AH30 - FCC and ISED Canada Statements............................................ 3
AH20/AH30 - Placement of Communication Hub......................................... 5
AH20/AH30 - Mounting, Americas Adapter Plate.......................................... 6
AH20/30 - Mounting, Bottom Cover .................................................................. 7
AH20 (J101) - Connections ................................................................................... 8
AH20 Advanced Wiegand (J100) - Connections..........................................10
AH20 - DIP Switch Configuration Table (S700).............................................11
AH30 (J101) - Connections ................................................................................12
AH30 - DIP Switch Configuration Table (S700).............................................13
AH30 - RS485 Bus Connection...........................................................................14
AH30 - RS485 Addressing ....................................................................................15
AH20/AH30 - Communication Hub LED Indication ....................................17
AH20/AH30 - Technical Data ..............................................................................18

3
AH20/AH30 - FCC and ISED Canada Statements
FCC Statements
Changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void the users authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.
ISED Canada Statements
This radio transmitter [IC:9504A-AH20R03] has been approved by Innovation,
Science and Economic Development Canada to operate with the antenna types
listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated
for any type listed are strictly prohibited for use with this device.
Antenna type Maximum antenna gain (dBi) Impedance (ohm)
Internal antenna 3.6 50
AH-ANTENNA-1 2.15 50

4
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le present émetteur radio [IC:9504A-AH20R03] a été approuvé par Innova-
tion, Sciences et Développement économique Canada pour fonctionner
avec les types d’antenne énumérés ci dessous et ayant un gain admissible
maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont
strictement interdits pour l’exploitation de l’émetteur.
Type d’antenne Gain d’antenne maxima (dBi) Impédance (ohm)
Antenne interne 3.6 50
AH-ANTENNA-1 2.15 50
L’émetteur/récepteur exempt de licence contenu dans le présent appareil
est conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :

5
AH20/AH30 - Placement of Communication Hub
AH20/30 - Placement of the Hub, 1 door
Note: AH20/AH30 can be installed with an Aperio bottom cover or
Americas adapter plate.
< 25 m / ~ 80 ft
AH30 (RS485 Hub) - Placement of the Hub, 1-16 doors
Note: AH20/AH30 must be installed into a junction box ex
European 2-Gang, Aperio bottom cover or with Americas adapter
plate to junction box. AH20/AH30 must be installed by qualified
and trained personal. Indoor installation only!
< 25 m / ~ 80 ft

6
1
3 4
5
2
AH40 - Mounting, Americas Adapter Plate
Americas
Adapter
Plate
Top Cover
External
Antenna
Option
Screw
(4 x 35 mm)
Screw
(3 x 10 mm)
AH20/30 - Mounting, Americas Adapter Plate
(US version)

7
1
3
2
AH40 - Mounting, Bottom Cover
Bottom Cover
Top Cover
External
Antenna
Option
Screw
(4 x 35 mm)
Screw
(3 x 10 mm)
AH20/30 - Mounting, Bottom Cover (EU version)

8
AH20 (J101) - Connections
AH20 Advanced Wiegand Connectors (J101)
AH20 Standard Wiegand Connectors (J101)
Note: The installation must comply with national wiring regulations.
NCL1
COM1
1234
NOP1
NCL2
COM2
NOP2
NCL3
COM3
NOP3
NCL4
COM4
NOP4
A
A0 A1 A2 A3 A4
EXT
INT
TERM
B
D1
D0
RED
GREEN
GND
8-24VDC
J101
J100
S700
S100
ON
OFF12345678
A
A0 A1 A2 A3 A4
EXT
INT
TERM
B
D1
D0
RED
GREEN
GND
8-24VDC
J101
S700
S100

9
Communication Hub hardware version AH20 has four Wiegand
signals plus power supply. The purpose and connection of these
signals are described in the table below.
Hub
ConneCtor DesCription
D1 Wiegand Data 1 signal. Output from Communication Hub.
Used to transmit credentials.
D0 Wiegand Data 0 signal. Output from Communication Hub.
Used to transmit credentials.
RED
Wiegand Red LED signal. Input to Communication Hub. Used
for access decision. Leave unconnected if DIP switch 1 is
selected “OFF”. Signal is active low.
GREEN
Wiegand Green LED signal. Input to Communication Hub.
Used for access decision. Signal is active low.
See DIP 1 for alternate instructions.
GND GND = Signal ground. Should be connected to EAC system
GND and power supply GND.
8-24 VDC
Power supply input, 8-24 VDC, 2 W (AH20 Advanced)
alternatively 0.8 W (AH20 Standard and AH30). The power
supply shall be 3 A over current protected. Wire requirements
16-22 AWG.

10
AH20 Advanced Wiegand (J100) - Connections
AH20 Advanced Wiegand Connectors (J100)
relay ContaCts DesCription
NCL Normally Closed
COM Common
NOP Normally Open
NCL1
COM1
1234
NOP1
NCL2
COM2
NOP2
NCL3
COM3
NOP3
NCL4
COM4
NOP4
A
A0 A1 A2 A3 A4
EXT
INT
TERM
B
D1
D0
RED
GREEN
GND
8-24VDC
J101
J100
S700
S100
ON
OFF12345678
relays DesCription
Relay 1 DPS (Door Position)
Relay 2 RX (Request to exit)
Relay 3 Battery Alarm Output
Relay 4 Tamper Alarm Output/
Lock Jammed

11
Dip
switCH
number
label DesCription
1 A0
Controls use of Red LED signal for access decision.
ON => Red LED is used.
OFF => Red LED is ignored.
2 A1 Set to OFF by default. Reserved for future use.
3 A2
Controls addition of parity bits if required.
ON => Addition of parity bits is enabled.
OFF => Addition of parity bits is disabled.
Credentials are transmitted as received.
4 A3
Controls byte order of transmitted credentials.
ON => The byte order is reversed on the Wiegand
interface compared to what is received from the
Aperio®lock.
OFF => The byte order is left as is.
5 A4
Used in “Pairing Mode”.
ON => Starts in pairing mode.
OFF => Normal use.
Note: If the DIP switch is moved from ON to OFF within
10 seconds from boot up and the Hub LED is lit, all
paired devices will be unpaired.
6-7 Not applicable (only used for AH30).
8INT/
EXT Internal/External Antenna Use, ON = Internal
AH20 - DIP Switch Configuration Table (S700)

12
AH30 (J101) - Connections
AH30 (J101) Connectors
Hub
ConneCtor DesCription
ARS485 Data A.
BRS485 Data B.
GND GND = Signal ground. Should be connected to EAC system
GND and power supply GND.
8-24 VDC Power supply input, 8-24 VDC, 2 W (AH20 Advanced)
alternatively 0.8 W (AH20 Standard and AH30).
Note: The installation must comply with national wiring regulations.
A
A0 A1 A2 A3 A4
EXT
INT
TERM
B
D1
D0
RED
GREEN
GND
8-24VDC
J101
S700
S100
12345678
A0 A1 A2 A3 A4
EXT
INT
TERM
S700
ON
OFF12345678

13
Dip
switCH
number
label DesCription
1-5 A0-A4
Controls RS485 addressing BIT 0-BIT 4.
ON => Address bit set.
OFF => Address bit NOT set.
See AH30 - RS485 Addressing Reference on page 13.
6-7 TERM
Control use of termination resistor between RS485 A
and RS485 B.
For termination to be enabled, both switches must
be set to ON.
ON =>120 Ohm termination resistor connected/
enabled.
OFF => 120 Ohm termination resistor disconnected/
disabled.
8 INT/EXT
Controls use of external antenna if required.
ON =>Selects use of internal antenna.
OFF => Selects use of external antenna.
AH30 - DIP Switch Configuration Table (S700)

14
Communication Hub Connections, examples
AH30 - RS485 Bus Connection
Here are examples of connection of multiple Communication Hubs to
a single RS485 bus of an EAC system. Termination should be enabled to
the last Hub on the bus.
EAC system
A
B
A
Termination
enabled
B
A
B
A
B
Hub 1
DIP 6 OFF
DIP 7 OFF
Hub 2
DIP 6 OFF
DIP 7 OFF
Hub N
End of Bus
DIP 6 ON
DIP 7 ON
EAC system
A
B
A
Termination
enabled
B
A
B
Hub 2
DIP 6 ON
DIP 7 ON
Hub 1
DIP 6 ON
DIP 7 ON
Note: The RS485 bus cable should be of type twisted pair. The
maximum cable length of 1000 meters should not be exceeded.

15
aDDress a0 a1 a2 a3 a4*
0 Pairing Active*
1 ON
2 ON
3 ON ON
4 ON
5 ON ON
6 ON ON
7 ON ON ON
8 ON
9 ON ON
10 ON ON
11 ON ON ON
12 ON ON
13 ON ON ON
14 ON ON ON
15 ON ON ON ON
Address examples
*) Note: If any of the A0-A4 DIP switches are moved from OFF to ON
within 10 seconds from boot up and the Hub LED is lit, all paired
devices will be unpaired.
AH30 - RS485 Addressing

16
aDDress a0 a1 a2 a3 a4*
16 ON
17 ON ON
18 ON ON
19 ON ON ON
20 ON ON
21 ON ON ON
22 ON ON ON
23 ON ON ON ON
24 ON ON
25 ON ON ON
26 ON ON ON
27 ON ON ON ON
28 ON ON ON
29 ON ON ON ON
30 ON ON ON ON
31 ON ON ON ON ON
Address examples
*) A4 is only supported on AH30 in 1 - 1 mode.

17
The Communication Hub has a single LED that supports an
optical scheme with red, green and yellow. The indication
scheme is described by the two figures below:
AH20/AH30 - Communication Hub LED Indication
GreenOnline
Green + One
Red Flash
Aperio® Lock
Offline
Green + Two
Red Flashes
EAC Offline
Green + Three
Red Flashes
Aperio® Lock and
EAC Offline
Yellow + Off,
Fast Flash
UHF
Communication
YellowPairing Active
Note: With the software tool Aperio®Programming Application
and a USB radio dongle, further system installation parameters
can be set.

18
Physical Dimensions 82 mm x 82 mm x 37 mm (H x W x T)
Power Supply 8-24 VDC
Power Rating
The power supply shall be able to deliver minimum
2 W (AH20 Advanced) alternatively 0.8 W (AH20
Standard and AH30) and be 3 A over current
protected. Wire requirements 16-22 AWG.
Radio Standard
IEEE 802.15.4 (2400 – 2483,5MHz)
16 channels (11-26)
AES 128 bit encryption
Receiver Sensitivity -100 dBm
Wireless Transmit
Power
10 dBm/MHz. Peak value from average detector
according to EN ETSI 300 328 Maximum spectral
density.
Wireless Operating
Range
Indoors up to 25 m depending upon installed
environment.
Internal Antenna Two cross polarized dipoles.
External Antenna
One reverse polarity SMA external antenna
connector. AH20/30 is certified to be used with
ASSA ABLOY external antenna AH-ANTENNA-1. If
other external antenna is used it must be of same
type (dipole) and not have larger antenna gain than
3.6 dBi.
Operating
Temperature 5 °C to 35 °C.
Humidity < 95 % non-condensing.
IP Classification IP20
Safety, Radio and
EMC
IEC 62368-1:2014
EN 62368-1:2014 + A11:2017
UL/CSA 62368-1:2014
EN 301 489-1 V2.1.1
EN 301 489-17 V3.2.0
EN 300 328 V2.2.2
EN 50130-4:2011 + A1:2014
EN 62311
FCC 47CFR Part 15 subpart B and subpart C
ISED RSS-247 and ICES-003
AS/NZS 4268
AH20/AH30 - Technical Data

19
NOTE

20
www.assaabloy.com/aperio
D001042371-1
Experience a safer
and more open world