Assa Abloy Aperio AH30 User manual

1
ASSA ABLOY, the global leader
in door opening solutions
Covers AAWL-260
3 May 2011
Aperio™ Hub
AH20/AH30
Installation Instructions

2
AH20/AH30 - FCC and Industry Canada Statements 3
AH20/AH30 - Placement of Communication Hub 4
AH20 (J100) - Connections 5-6
AH20 (J103) - Connections 7
AH20 - DIP Switch Configuration Table 8
AH30 (J100) - Connections 9
AH30 - DIP Switch Configuration Table 10
AH30 - RS485 Bus Connection 11
AH30 - RS485 Addressing 12-13
AH20/AH30 - Communication Hub LED Indication 14
AH20/AH30 - Technical Data 15
ETL marking
Recognized component
Conforms to ANSI/UL standard 294, ANSI/UL 60950-1
Certified to CAN/CSA standard C22.2 No. 60950-1
4002570
AH20/AH30 - Table of Contents

3
AH20/AH30 - FCC and Industry Canada Statements
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that
may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence.L’exploitation est autorisée aux deux
conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
The term “IC:” before the equipment certification number only signifies that the
Industry Canada technical specifications were met.
Le terme “IC” devant le numéro de certification signifie seulement que les
spécifications techniques Industrie Canada ont été respectées.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
IEEE 802.15.4 operation of this product in U.S.A. and Canada is limited to
channels 11-25 by Aperio Programming Application. Outside of U.S.A. and
Canada another version of the Aperio programming application allow use of
channels 11-26.

4
AH20/AH30 - Placement of Communication Hub
AH20 (Wiegand Hub) - Placement of the Hub, 1 door
Note: AH20 can be installed with an Aperio bottom cover or
Americas adaptor plate.
< 25 m / ~ 82 ft
AH30 (RS485 Hub) - Placement of the Hub, 1-8 doors
Note: Note: AH20/AH30 must be installed into a junction box ex
European 2-Gang, Aperio bottom cover or with Americas adaptor
plate to junction box. AH20/AH30 shall only be installed with
qualified and trained personal. Indoor installation only!
< 25 m / ~ 82 ft

5
AH20 (J100) - Connections
AH20 Connectors (J100)
Note: The installation shall comply with national wiring regulations.

6
Hub
ConneCtor DesCription
DATA 1 Wiegand Data 1 signal. Output from Communication Hub.
Used to transmit credentials.
DATA 0 Wiegand Data 0 signal. Output from Communication Hub.
Used to transmit credentials.
RED
Wiegand RED LED signal. Input to Communication Hub. Used
for access decision. Leave unconnected if DIP switch 1 is
selected “OFF”. Signal is active low.
GREEN
Wiegand Green LED signal. Input to communication Hub.
Used for access decision. Signal is active low.
See DIP 1 for alternate instructions.
GND GND = Signal ground. Should be connected to EAC system
GND and power supply GND.
8-24 VDC
Power supply input, 8-24 V DC. The power supply shall be
a Limited Power Source (LPS) according to EN 60950-1.
The power supply shall be 3A over current protected. Wire
requirements 16-22 AWG.
AH20 (J100) - Connections
Communication Hub hardware version AH20 has four
Wiegand signals plus power supply. The purpose and
connection of these signals are described in the table
below.
AH20 Connectors (J100)

7
AH20 (J103) - Connections
AH20 Connectors (J103)
Relay max voltage: 30 VDC
Relay max current: 1 A
resistive load
On the AH20 four form C
relays are available.The
purpose of the four relays
is to provide door status
information to the EAC
system.
relays DesCription
Relay 1 DPS
Relay 2 RX
Relay 3 Battery Alarm Output
Relay 4 Tamper Alarm Output/
Lock Jammed
relay ContaCts DesCription
NCL Normal Closed
COM Common
NOP Normal Open

8
Dip
switCH
number
label DesCription
1 A0
Controls use of LED Red signal for access decision.
ON => LED Red is used.
OFF => LED Red is ignored.
2 A1 Set to OFF by default. Reserved for future use.
3 A2
Controls addition of parity bits if required.
ON => Addition of parity bits is enabled.
OFF => Addition of parity is disabled.
Credentials are transmitted as received.
4 A3
Controls byte order of transmitted credentials.
ON => The byte order is reversed compared
to what is received as input to the Hub Wiegand EAC
interface component.
OFF => The byte order is left as is.
5 A4
Used in “Pairing Mode”.
ON => Starts in pairing mode.
OFF => Normal use.
6-8 Not applicable (only used for AH30).
9 Not used.
10 INT/
EXT Internal/External Antenna Use, ON = Internal
AH20 - DIP Switch Configuration Table

9
AH30 (J100) - Connections
AH30 (J100) Connectors
Hub
ConneCtor DesCription
ARS485 Data A.
BRS485 Data B.
GND GND = Signal ground. Should be connected to EAC system
GND and power supply GND.
8-24 VDC
Power supply input, 8-24 V DC. The power supply shall be
a Limited Power Source (LPS) according to EN 60950-1.
The power supply shall be 3A over current protected. Wire
requirements 16-22 AWG.
Note: The installation shall comply with national wiring regulations.

10
Dip
switCH
number
label DesCription
1-5
A0-A4
Controls RS485 addressing BIT 0-BIT 4.
ON => Address bit set.
OFF => Address bit NOT set.
See AH30 - RS485 Addressing Reference on page 13.
6 DOWN
Controls use of RS485 pull down resistor.
ON => 620 Ohm pull down connected/enabled.
OFF => 620 Ohm pull down disconnected/disabled.
7 UP
Controls use of RS485 and pull up resistor.
ON =>620 Ohm pull up connected/enabled.
OFF => 620 Ohm pull up disconnected/disabled.
8 TERM
Controls use of termination resistor between RS485
A and RS485 B.
ON =>100 Ohm termination resistor connected/
enabled.
OFF => 100 Ohm termination resistor disconnected/
disabled.
9 Not used.
10 INT/EXT
Controls use of external antenna if required.
ON =>Selects use of internal antenna.
OFF => Selects use of external antenna.
AH30 - DIP Switch Configuration Table

11
Communication Hub Connections, examples
AH30 - RS485 Bus Connection
Examples of connection of multiple Communication Hubs
to a single RS-485 bus of an EAC system:
EAC system
A
B
A
Termination
enabled
B
A
B
A
B
Hub 1
DIP 6 OFF
DIP 7 OFF
DIP 7 OFF
Hub 2
DIP 6 OFF
DIP 7 OFF
DIP 7 OFF
Hub N
End of Bus
DIP 6 ON
DIP 7 ON
DIP 7 ON
EAC system
A
B
A
Termination
enabled
B
A
B
Hub 2
DIP 6 OFF
DIP 7 OFF
DIP 7 ON
Hub 1
DIP 6 ON
DIP 7 ON
DIP 7 ON
Note: The RS485 bus cable should be of type twisted pair. The
maximum cable length of 1000 meters should not be exceeded.

12
aDDress
a0 a1 a2 a3 a4*
0 Pairing Active
1 ON
2 ON
3 ON ON
4 ON
5 ON ON
6 ON ON
7 ON ON ON
8 ON
9 ON ON
10 ON ON
11 ON ON ON
12 ON ON
13 ON ON ON
14 ON ON ON
15 ON ON ON ON
Address examples
AH30 - RS485 Addressing

13
AH30 - RS485 Addressing
aDDress
a0 a1 a2 a3 a4*
16 ON
17 ON ON
18 ON ON
19 ON ON ON
20 ON ON
21 ON ON ON
22 ON ON ON
23 ON ON ON ON
24 ON ON
25 ON ON ON
26 ON ON ON
27 ON ON ON ON
28 ON ON ON
29 ON ON ON ON
30 ON ON ON ON
31 ON ON ON ON ON
Address examples
* = A4 is only supported on AH30 in 1 - 1 mode.

14
The Communication Hub has a single LED that supports an
optical scheme with red, green and yellow. The indication
scheme is described by the two figures below:
AH20/AH30 - Communication Hub LED Indication
GreenOnline
Green + One
Red Flash
Aperio Lock
Offline
Green + Two
Red Flashes
EAC Offline
Green + Three
Red Flashes
Aperio Lock and
EAC Offline
Yellow + Off,
Fast Flash
UHF
Communication
YellowPairing Active
Note: With the software tool AperioTM Programming Application
and an USB radio dongle, further system installation parameters
can be set.

15
Physical Dimensions 82 mm x 82 mm x 37 mm (H x W x T)
Power Supply 8-24 VDC
Current 250 mA. Minimum 80 mA at 12 VDC.
Radio Standard
IEEE 802.15.4 (2400 – 2483,5MHz)
16 channels (11-26)
15 channels in USA and Canada (11-25)
AES 128 bit encryption
Receiver Sensitivity -100 dBm 20%PER
Wireless Transmit
Power
10 dBm/MHz. Peak value from average detector
according to EN ETSI 300 328 Maximum spectral
density.
Wireless Operating
Range
Indoors 15-25 meters depending
upon installed environment.
Internal Antenna Two cross polarized dipoles.
External Antenna
One reverse polarity SMA external antenna
connector. AH20/30 is certified to be used with
Assa Abloy external antenna AH-ANTENNA-1. If
other external antenna is used it must be of same
type (dipole) and not have larger antenna gain than
3,9dBi.
Operating
Temperature 5°C to 35°C.
Humidity < 95% non-condensing.
IP Classification IP20
Safety and
Emissions
FCC 47CFR Part 15 subpart B and subpart C
IC RSS-210
EN ETSI 301 489-17 v2.1.1
EN ETSI 300 328 v1.7.1
EN 60950-1 ed.2 2007
UL 294-2010
C22.2
AH20/AH30 - Technical Data

16
www.assaabloy.com/aperio
ASSA ABLOY, the global leader
in door opening solutions
M2665.1302 ST-001810-A-EN