Asus Eee PC 900 XP Operating manual

Quick Use Guide
Eee PC 900 Series
E3674
15G06Q013000

Quick Use Guide - 2
Powering on your Eee PC
These are only quick instructions for using your Eee PC. Read the full
manual for detailed information.
1. Install the battery pack 2. Connect the AC power
adapter
1
1
2
1
3
2
3. Turn ON the Eee PC
Remember to fully charge the battery before first use and
whenever it is depleted to prolong battery life.
Status Indicators
Status indicators represent various hardware/software conditions.
Power Indicator
Battery Charge Indicator
When you open the display panel, do not force it down to the
table or else the hinges may break! Never lift the Eee PC by the
display panel!
Solid State disk (SSD)
Indicator
Wireless Indicator
Damage may occur if you
use a different adapter
to power the Eee PC.You
may damage both your
battery pack(s) and the
Eee PC with a faulty AC-DC
adapter.

Quick Use Guide - 3
Powering off your Eee PC
Do the following instructions to turn down your Eee PC.
A.
1. Click the red power switch in the Notification area.
Or, click Instant Shutdown from the Settings tab and select
Shutdown.
2. Select Shut Down from the dialogue box.
3. Select OK to proceed.
1
2
3
1
B.
Or, press the power switch of the Eee PC directly, and follow the
previous instructions to shut down your Eee PC.

Quick Use Guide - 4
Launching First Run Wizard
For the first time you start your Eee PC, the First Run Wizard will
auto-launch and lead you through setting up your preferences and
some basic information. Follow the wizard instructions to finish the
initiation.
1. Toggle I agree with
this license and click
Next to continue.
ASUS Eee PC also supports Windows® XP operating system. Refer
to user guide for detailed instructions and notices on installing
the WinXP SP2 32 bit operating system.
3. Follow the on-screen instructions to complete the first run
wizard.
2. Select your keyboard
type and click Next
to continue.
3. Enter your User
Name. Click Next to
continue.

Quick Use Guide - 5
Conguring a network connection
Wireless network
connection
1. Press + (<Fn> +
<F2>) to activate the wireless
LAN function.
4. When connecting, you may
have to enter a password.
5. After a connection has been
established, the connection is
shown on the list.
3. Select the wireless access
point you want to connect
to from the list and click
Connect to build the
connection. Ensure that the
box before Enable wireless is
checked.
6. And you can see the wireless
signal strength bars in the
Notification area.
2. Click Wireless Networks
from Internet tab.

Quick Use Guide - 6
Using a dynamic IP:
1. From the Internet tab,
select Network to start the
configuration.
Local Area Network
3. Select the type of connection
you are using and click Next.
5. Toggle the first option
Dynamic IP address (DHCP)
and click Next.
2. Click Create to create a
network connection.
6. Enter a name for this connection and click Next.
7. Click Finish to apply the
settings or click Back to make
changes. Click the box before
Connect automatically at
system startup or before the
box Start this connection
when finished based on your
needs.
4. Select the hardware that you
want to use to make your
connection and click Next.

Quick Use Guide - 7
Point-to-Point Protocol over Ethernet (PPPoE)
1. Repeat the step 1–2 of Using a static IP to start the PPPoE
network configuraton.
3. Select the hardware that you
want to use to make your
connection and click Next.
5. Enter a name for this
connection and click Next.
6. Click Finish to apply the
settings or click Back to make
changes.
4. Enter your user and password
and click Next..
2. Select the type of connection
you are using and click Next.

Quick Use Guide - 8
Connecting removable devices
You can connect removable devices based on your needs.
1 2
Memory Card Slot
SD (Secure Digital)
MiniSD (with SD adapter)
MMC (Multimedia Card)
MMC Plus
RS-MMC (Reduced Size) (with MMC adapter)
2.0
USB Port (2.0/1.1)
1
2
USB Flash Memory Disk
USB External Hard Disk DriveUSB External Optical Disk Drive
microSD
SD Adapter

Quick Use Guide - 9
Accessing your les
With external connection of USB devices, you can easily move files
into and out of your Eee PC. Refer to the sub-sections below for more
information.
File Manager
1. Connect your USB flash memory disk or USB portable hard disk
drive to your Eee PC.
2. Highlight and select Open in File Manager at the prompt.
3. All the files and folders in your USB external storage device are
shown in the right pane. Locate the desired file and double-click
it to open.

Quick Use Guide - 10
Music Manager
1. Connect your USB flash memory disk or USB portable hard disk
drive to your Eee PC with your music.
2. Highlight and select Open
in Music Manager at the
prompt.
3. The Music Manager screen displays the album folders in your
USB flash/hard disk drive. Select a folder and drag tracks to the
right pane to create your own playlist.