Asus Ap2400r-e2 User manual

Dual IntelDual Intel

Dual Intel

®®

Xeon™ 2U Rackmount ServerXeon™ 2U Rackmount Server

Xeon™ 2U Rackmount Server

800 MHz Front Side Bus800 MHz Front Side Bus

800 MHz Front Side Bus

Service Guide

AP2400R-E2

iiii

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form

or by any means, except documentation kept by the purchaser for backup purposes, without the

express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS provides this manual “as is” without warranty of any kind, either express or implied,

including but not limited to the implied warranties or conditions of merchantability or fitness for

a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable

for any indirect, special, incidental, or consequential damages (including damages for loss of

profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS

has been advised of the possibility of such damages arising from any defect or error in this

manual or product.

Specifications and information contained in this manual ae furnished for informational use only,

and are subject to change at any time without notice, and should not be construed as a

commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies

that may appear in this manual, including the products and software described in it.

Product warranty or service will not be extended if: (1) the product is repaired, modified or

altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the

serial number of the product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identification or

explanation and to the owners’ benefit, without intent to infringe.

E1800E1800

E1800

First edition V1First edition V1

First edition V1

June 2005June 2005

June 2005

iiiiii

iii

Contents

Notices ................................................................................................ vi

Safety information ............................................................................. vii

About this guide ............................................................................... viii

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

1.1 System package contents .................................................... 1-2

1.2 System specifications .......................................................... 1-3

1.2 System specifications .......................................................... 1-4

1.3 Front panel features ............................................................. 1-5

1.4 Rear panel features .............................................................. 1-5

1.5 Internal features ................................................................... 1-6

1.6 LED information .................................................................... 1-7

1.6.1 Front panel LEDs .................................................... 1-7

1.6.2 Rear fan LEDs ......................................................... 1-8

1.6.3 System fan LED ...................................................... 1-8

1.6.4 Power supply LED ................................................... 1-9

1.6.5 LAN port LEDs ........................................................ 1-9

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

2.1 Chassis cover ....................................................................... 2-2

2.1.1 Removing the front bezel ....................................... 2-2

2.1.2 Removing the top cover ......................................... 2-3

2.1.3 Installing the top cover .......................................... 2-5

2.1.4 Removing the air duct ............................................ 2-6

2.1.5 Installing the air duct .............................................. 2-6

2.2 Central Processing Unit (CPU) .............................................. 2-8

2.2.1 Removing the CPU heatsink .................................... 2-8

2.2.2 Installing a CPU ....................................................... 2-9

2.2.3 Installing the CPU heatsink ................................... 2-12

2.3 System memory ................................................................. 2-13

2.3.1 Memory configurations ......................................... 2-13

2.3.2 Installing a DIMM ................................................... 2-14

2.3.3 Removing a DIMM ................................................. 2-14

2.4 Hard disk drives .................................................................. 2-15

2.5 Expansion cards .................................................................. 2-17

2.5.1 Installing a low-profile expansion card .................. 2-17

2.5.2 Installing a full-length expansion card .................. 2-18

2.5.3 ZCR socket ........................................................... 2-21

2.5.4 Configuring an expansion card.............................. 2-22

iviv

Contents

2.6 Cable connections .............................................................. 2-23

2.6.1 Motherboard ......................................................... 2-24

2.6.2 SCSI backplanes .................................................... 2-25

2.6.3 SCSI HDD configurations ....................................... 2-26

2.6.4 SCSI ID assignments ............................................. 2-29

2.6.5 SCSI jumper settings ............................................ 2-29

2.6.6 SMBus and backplane power cabling .................... 2-30

2.6.7 Fan boards ............................................................ 2-31

2.7 Removable components ..................................................... 2-33

2.7.1 Hot-swap mid-fans (80mm) ................................. 2-33

2.7.2 Rear fans (60mm) ................................................ 2-34

2.7.3 Power supply modules .......................................... 2-34

2.7.4 Slim optical and floppy drives ............................... 2-35

2.7.5 Front panel LED and switch board ........................ 2-36

2.7.6 SCSI backplanes .................................................... 2-36

Chapter 3:Chapter 3:

Chapter 3: Installation optionsInstallation options

Installation optionsInstallation options

Installation options

3.1 Rackmount rail kit items ....................................................... 3-2

3.2 Attaching the rails to the server .......................................... 3-3

3.3 Attaching the rack rails ........................................................ 3-4

3.4 Rackmounting the server ..................................................... 3-6

Chapter 4:Chapter 4:

Chapter 4: Motherboard infoMotherboard info

Motherboard infoMotherboard info

Motherboard info

4.1 Motherboard layout .............................................................. 4-2

4.2 Jumpers ................................................................................ 4-4

4.3 Connectors ........................................................................... 4-9

Chapter 5:Chapter 5:

Chapter 5: BIOS informationBIOS information

BIOS informationBIOS information

BIOS information

5.1 Managing and updating your BIOS ........................................ 5-2

5.1.1 Creating a bootable floppy disk .............................. 5-2

5.1.2 AFUDOS utility ........................................................ 5-3

5.1.3 ASUS CrashFree BIOS 2 utility ................................ 5-6

5.1.4 ASUS Update utility ................................................ 5-8

5.2 BIOS setup program ........................................................... 5-11

5.2.1 BIOS menu screen ................................................. 5-12

5.2.2 Menu bar ............................................................... 5-12

5.2.3 Navigation keys .................................................... 5-12

5.2.4 Menu items ........................................................... 5-13

5.2.5 Sub-menu items ................................................... 5-13

Contents

5.2.6 Configuration fields .............................................. 5-13

5.2.7 Pop-up window ..................................................... 5-13

5.2.8 Scroll bar .............................................................. 5-13

5.2.9 General help .......................................................... 5-13

5.3 Main menu .......................................................................... 5-14

5.3.1 System Time ......................................................... 5-14

5.3.2 System Date ......................................................... 5-14

5.3.3 Legacy Diskette A ................................................ 5-14

5.3.4 Primary/Secondary IDE Master/Slave,

Third and Fourth IDE/SATA .................................. 5-15

5.3.5 IDE Configuration .................................................. 5-17

5.3.6 System Information .............................................. 5-18

5.4 Advanced menu .................................................................. 5-19

5.4.1 USB Configuration ................................................. 5-19

5.4.2 MPS Configuration ................................................ 5-21

5.4.3 Remote Access Configuration .............................. 5-22

5.4.4 CPU Configuration ................................................. 5-24

5.4.5 Chipset ................................................................. 5-25

5.4.6 Onboard Devices Configuration ............................ 5-27

5.4.7 PCI PnP ................................................................. 5-28

5.5 Power menu ........................................................................ 5-30

5.5.1 ACPI APIC Support ................................................ 5-30

5.5.2 APM Configuration ................................................ 5-30

5.5.3 Hardware Monitor ................................................. 5-33

5.6 Boot menu .......................................................................... 5-35

5.6.1 Boot Device Priority .............................................. 5-35

5.6.2 Boot Settings Configuration ................................. 5-36

5.6.3 Security ................................................................ 5-37

5.7 Exit menu ........................................................................... 5-40

Appendix:Appendix:

Appendix: ReferencesReferences

ReferencesReferences

References

A.1 Power supply ........................................................................ A-2

A.1.1 General description ................................................. A-2

A.1.2 Specifications ......................................................... A-3

A.2 Qualified Vendors List (QVL) ............................................... A-4

A.3 Troubleshooting ................................................................... A-6

A.4 NCL-DS1R2 block diagram.................................................... A-8

vivi

Notices

Federal Communications Commission StatementFederal Communications Commission Statement

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

•

This device may not cause harmful interference, and

•

This device must accept any interference received including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

manufacturer’s instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications StatementCanadian Department of Communications Statement

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

This class B digital apparatus complies with Canadian ICES-003.This class B digital apparatus complies with Canadian ICES-003.

This class B digital apparatus complies with Canadian ICES-003.

WARNING!WARNING!

WARNING! The use of shielded cables for connection of the monitor to

the graphics card is required to assure compliance with FCC regulations.

Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user’s authority to

operate this equipment.

viivii

vii

Safety information

Electrical safetyElectrical safety

Electrical safety

• Before installing or removing signal cables, ensure that the power cables

for the system unit and all attached devices are unplugged.

• To prevent electrical shock hazard, disconnect the power cable from the

electrical outlet before relocating the system.

• When adding or removing any additional devices to or from the system,

ensure that the power cables for the devices are unplugged before the

signal cables are connected. If possible, disconnect all power cables from

the existing system before you add a device.

• If the power supply is broken, do not try to fix it by yourself. Contact a

qualified service technician or your dealer.

Operation safetyOperation safety

Operation safety

• Any mechanical operation on this server must be conducted by certified

or experienced engineers.

• Before operating the server, carefully read all the manuals included with

the server package.

• Before using the server, make sure all cables are correctly connected and

the power cables are not damaged. If any damage is detected, contact

your dealer as soon as possible.

• To avoid short circuits, keep paper clips, screws, and staples away from

connectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Place the server on a

stable surface.

Heavy SystemHeavy System

Heavy System

CAUTION!CAUTION!

CAUTION! This server system is heavy. Ask for assistance when

moving or carrying the system.

This product is equipped with a three-wire power cable and plug for the

user’s safety. Use the power cable with a properly grounded electrical

outlet to avoid electrical shock.

Lithium-Ion Battery WarningLithium-Ion Battery Warning

Lithium-Ion Battery Warning

CAUTION!CAUTION!

CAUTION! Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer. Dispose of used batteries according to the

manufacturer’s instructions.

CD-ROM Drive Safety WarningCD-ROM Drive Safety Warning

CD-ROM Drive Safety Warning

CLASS 1 LASER PRODUCTCLASS 1 LASER PRODUCT

CLASS 1 LASER PRODUCT

viiiviii

viii

About this guide

AudienceAudience

Audience

This user guide is intended for system integrators and experienced users

with at least basic knowledge of configuring a server.

ContentsContents

Contents

This guide contains the following parts:

1.1.

1. Chapter 1: Product IntroductionChapter 1: Product Introduction

Chapter 1: Product IntroductionChapter 1: Product Introduction

Chapter 1: Product Introduction

This chapter describes the general features of the barebone server,

including sections on the front panel and rear panel specifications.

2.2.

2. Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

This chapter lists the hardware setup procedures that you have to

perform when installing or removing system components.

3.3.

3. Chapter 3: Installation optionsChapter 3: Installation options

Chapter 3: Installation optionsChapter 3: Installation options

Chapter 3: Installation options

This chapter describes how to prepare the barebone server for rack

mounting.

4.4.

4. Chapter 4: Motherboard informationChapter 4: Motherboard information

Chapter 4: Motherboard informationChapter 4: Motherboard information

Chapter 4: Motherboard information

This chapter gives information about the motherboard that comes

with the server. This chapter includes the motherboard layout, jumper

settings, and connector locations.

5.5.

5. Chapter 5: BIOS informationChapter 5: BIOS information

Chapter 5: BIOS informationChapter 5: BIOS information

Chapter 5: BIOS information

This chapter tells how to change the system settings through the

BIOS Setup menus. Detailed descriptions of the BIOS parameters are

also provided.

7.7.

7. Appendix: ReferencesAppendix: References

Appendix: ReferencesAppendix: References

Appendix: References

This appendix includes additional information that you may refer to

when configuring your barebone server.

ixix

ReferenceReference

Reference

Visit the ASUS websites worldwide that provide updated information for all

ASUS hardware and software products. Refer to the ASUS contact

information for details.

WARNING:WARNING:

WARNING: Information to prevent injury to yourself when trying

to complete a task.

CAUTION:CAUTION:

CAUTION: Information to prevent damage to the components

when trying to complete a task.

IMPORTANT:IMPORTANT:

IMPORTANT: Instructions that you MUST follow to complete a

task.

NOTE:NOTE:

NOTE: Tips and information to aid in completing a task.

ConventionsConventions

Conventions

To make sure that you perform certain tasks properly, take note of the

following symbols used throughout this manual.

1-1

ASUS AP2400R-E2ASUS AP2400R-E2

ASUS AP2400R-E2

This chapter describes the general

features of the barebone server,

including sections on the front

panel and rear panel specifications.

Chapter 1

Product introduction

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

1-21-2

1-2

1.1 System package contents

Check your system package for the following items.

ChassisChassis

Chassis ASUS AR21 2U rackmount chassis

MotherboardMotherboard

Motherboard ASUS NCL-DS1R2 motherboard

ComponentsComponents

Components 700W redundant power supply, 115V~230V

Slim optical drive|

Slim floppy disk drive

Chassis fan

HDD fan

Hot-swap SCSI HDD trays

SCSI backplanes

Front bezel

CPU heatsink (2 pcs.)

CablesCables

Cables RJ-45 extension connector

AC power cable

System cables

AccessoriesAccessories

Accessories Rackmount rail kit

AP2400R-E2 user guide

AP2400R-E2 support CD (includes ASWM*)

CA eTrust Anti-virus CD

AR21 chassis ears (left, right)

Thermal grease strip

Bag of screws

*ASUS System Web-based Management

If any of the above items is damaged or missing, contact your retailer.

ASUS AP2400R-E2ASUS AP2400R-E2

ASUS AP2400R-E2 1-31-3

1-31-3

1-3

1.2 System specifications

The ASUS AP2400R-E2 is a 2U barebone server system featuring the ASUS

NCL-DS1R2 motherboard. The server supports dual Intel® Xeon™

processors with EM64T technology, plus other latest technologies through

the chipsets onboard.

ChassisChassis

Chassis

MotherboardMotherboard

Motherboard

ChipsetChipset

Chipset

CPUCPU

CPU

MemoryMemory

Memory

LANLAN

LAN

VGAVGA

VGA

SCSISCSI

SCSI

ExpansionExpansion

Expansion

slotsslots

slots

StorageStorage

Storage

Front panelFront panel

Front panel

Rear panelRear panel

Rear panel

Rackmount 2U (AR21)

ASUS NCL-DS1R2

North Bridge: Intel

E7520 MCH

South Bridge: Intel

82801ER

I/O Bridge: Intel

6700PXH Bridge

Supports dual Intel

Xeon™ 3.6 GHz processors with L2

1 MB and 2 MB caches via two 604-pin sockets

8 x 184-pin DDR sockets for up to 16 GB system memory

Supports PC2700 registered ECC DDR DIMMs

2 x Broadcom® BCM5721 PCI Express Gigabit LAN

controllers

ATI RAGE-XL PCI-based VGA controller

Supports 8MB display memory

Adaptec

AIC-7902W Ultra320 Dual-channel SCSI controller

3 x full-length 64-bit/66MHz 3V PCI-X slots (on a riser card)

1 x low-profile 64-bit/133MHz 3V PCI-X slot

8 x 3.5-inch hot-swappable HDD bays

1 x slim optical drive

1 x slim 1.44MB floppy drive

2 x USB 2.0 ports

Power switch

Reset switch

Location switch

Power, HDD access, location, message, LAN

HDD LEDs: Status, activity

1 x PS/2 keyboard port

1 x PS/2 mouse port

1 x Serial port

1 x VGA port

2 x USB 2.0 ports

2 x RJ-45 ports (with LEDs)

1 x external SCSI port (alternative)

(continued on the next page)

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

1-41-4

1-4

1.2 System specifications

ManagementManagement

Management

HardwareHardware

Hardware

monitorsmonitors

monitors

Power supplyPower supply

Power supply

DimensionsDimensions

Dimensions

ASUS Server Web-based Management (ASWM)

Voltage, temperature, and fan speed monitoring

Automatic System Restart (ASR) feature

700W redundant power supply, 115V~230V, 50Hz~60Hz

732.5mm (l) x 448mm (w) x 87.7mm (h)

Refer to “Chapter 4 Motherboard information” for details on the internal

connectors.

ASUS AP2400R-E2ASUS AP2400R-E2

ASUS AP2400R-E2 1-51-5

1-51-5

1-5

1.3 Front panel features

The barebone server displays a simple yet stylish front panel with easily

accessible features. The power and reset buttons, LED indicators, location

switch, slim optical and floppy drives, and two USB ports are located on the

front panel.

1.4 Rear panel features

The rear panel includes the expansion slots, LAN, VGA, and I/O ports, fans,

and the system power sockets.

When disconnecting LAN cables, you need to remove the rear fan cage.

Refer to section “2.7 Removable components” for instructions on

removing the fan cage.

PS/2 keyboard portPS/2 keyboard port

PS/2 keyboard port

PS/2 mouse portPS/2 mouse port

PS/2 mouse port

VGA portVGA port

VGA port

Gigabit LAN2 portGigabit LAN2 port

Gigabit LAN2 port

Serial portSerial port

Serial port

AC power socketsAC power sockets

AC power sockets

Location switchLocation switch

Location switch

Location LEDLocation LED

Location LED

Expansion slotsExpansion slots

Expansion slots

USB 2.0 portsUSB 2.0 ports

USB 2.0 ports

External SCSIExternal SCSI

External SCSI

port (alternative)port (alternative)

port (alternative)

Rear fansRear fans

Rear fans

Redundant powerRedundant power

Redundant power

supply modulessupply modules

supply modules

Hot-swappable HDD baysHot-swappable HDD bays

Hot-swappable HDD bays

Slim optical driveSlim optical drive

Slim optical drive

Reset buttonReset button

Reset button

USB 2.0 portsUSB 2.0 ports

USB 2.0 ports

Power buttonPower button

Power button

Location switchLocation switch

Location switch

Slim floppy driveSlim floppy drive

Slim floppy drive

Front panel LEDsFront panel LEDs

Front panel LEDs

Rear fansRear fans

Rear fans

status LEDsstatus LEDs

status LEDs

Gigabit LAN1 portGigabit LAN1 port

Gigabit LAN1 port

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

1-61-6

1-6

1.5 Internal features

The barebone system includes the basic components as shown.

1. 2 x rear fans

2. 64-bit PCI-X slots

(underneath the PCI-X card

cage)

3. Low profile PCI-X slot

4. 8 x DDR DIMM sockets

5. Power supply cage

6. CPU2 socket with heatsink

7. CPU1 socket with heatsink

8. 7 x system fans

9. SCSI backplane 1

10. SCSI backplane 2

11. SCSI backplane 3

12. 3 x HDD bays

13. Top: Slim optical drive

Mid: Slim floppy drive

Bottom: 2 x HDD bays

14. 3 x HDD bays

The air duct lies on top of the motherboard components. Remove the air

duct to access the components. Refer to section “2.1.4 Removing and

installing the air duct” for instructions.

233

344

677

91010

1010

122

211

133

1111

144

PCI-X card cagePCI-X card cage

PCI-X card cage

ASUS AP2400R-E2ASUS AP2400R-E2

ASUS AP2400R-E2 1-71-7

1-71-7

1-7

1.6 LED information

1.6.11.6.1

1.6.1 Front panel LEDsFront panel LEDs

Front panel LEDsFront panel LEDs

Front panel LEDs

The location switch and LED are for service purposes. When the system

fails or is shut down, the server administrator can press either the front

or the rear location switch to identify the location of the specific 2U

system in a rack cabinet.

LEDLED

LED IconIcon

IconIcon

Icon Display statusDisplay status

Display statusDisplay status

Display status DescriptionDescription

DescriptionDescription

Description

Power LED ON System power ON

Storage Access LED OFF No activity

Blinking Read/write data into the HDD

Message LED OFF System is normal; no incoming event

Blinking ASWM indicates a HW monitor event

Location LED OFF Normal status

ON Location switch is pressed

(Press the location switch again to turn off)

LAN1 LED OFF No 64-bit Gbit LAN connection

Blinking LAN is transmitting or receiving data

ON LAN connection is present

LAN2 LED OFF No 64-bit Gbit LAN connection

Blinking LAN is transmitting or receiving data

ON LAN connection is present

Power LEDPower LED

Power LED

Location LEDLocation LED

Location LED

Message LEDMessage LED

Message LED

Storage Access LEDStorage Access LED

Storage Access LED

LAN1 LEDLAN1 LED

LAN1 LED

LAN2 LEDLAN2 LED

LAN2 LED

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

1-81-8

1-8

1.6.21.6.2

1.6.2 Rear fan LEDsRear fan LEDs

Rear fan LEDsRear fan LEDs

Rear fan LEDs

LEDLED

LED ColorColor

ColorColor

Color DescriptionDescription

DescriptionDescription

Description

LED1 Green Rear Fan 1 is in normal operation

Orange Rear Fan 1 is faulty

LED2 Green Rear Fan 2 is in normal operation

Orange Rear Fan 2 is faulty

1.6.31.6.3

1.6.3 System fan LEDSystem fan LED

System fan LEDSystem fan LED

System fan LED

Each system fan has an LED to indicate the fan status.

LEDLED

LED ColorColor

ColorColor

Color DescriptionDescription

DescriptionDescription

Description

LED Green Fan is in normal operation

Orange Fan is faulty

LEDLED

LED

LED1 forLED1 for

LED1 for

Rear Fan 1Rear Fan 1

Rear Fan 1

LED2 forLED2 for

LED2 for

Rear Fan 2Rear Fan 2

Rear Fan 2

ASUS AP2400R-E2ASUS AP2400R-E2

ASUS AP2400R-E2 1-91-9

1-91-9

1-9

1.6.41.6.4

1.6.4 Power supply LEDPower supply LED

Power supply LEDPower supply LED

Power supply LED

Each system fan has an LED to indicate the fan status.

LEDLED

LED ColorColor

ColorColor

Color Display statusDisplay status

Display statusDisplay status

Display status DescriptionDescription

DescriptionDescription

Description

LED Green Blinking Power off and in standby mode

Green On The power supply module is in normal operation

Orange On One of the two power modules is disconnected

from the power outlet or is defective

Off Off Both power supply modules are disconnected

from the power outlet or are defective

LEDLED

LED

1.6.51.6.5

1.6.5 LAN port LEDsLAN port LEDs

LAN port LEDsLAN port LEDs

LAN port LEDs

ACT/LINK LEDACT/LINK LED

ACT/LINK LED SPEED LEDSPEED LED

SPEED LEDSPEED LED

SPEED LED

StatusStatus

Status DescriptionDescription

DescriptionDescription

Description StatusStatus

StatusStatus

Status DescriptionDescription

DescriptionDescription

Description

OFF No link OFF 10 Mbps connection

GREEN Linked ORANGE 100 Mbps connection

BLINKING Data activity GREEN 1 Gbps connection

SPEED LEDSPEED LED

SPEED LED

ACT/LINK LEDACT/LINK LED

ACT/LINK LED

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

1-101-10

1-10

Table of contents

Other Asus Server manuals

Popular Server manuals by other brands

Supermicro

Supermicro SuperServer E300-9A-8CN10P user manual

Silex technology

Silex technology Silex SX-5000U2 Technical specifications

Fujitsu

Fujitsu PRIMERGY H200 manual

Lucent

Lucent Stinger FS Administration guide

NEC

NEC NEC Express5800 Series installation guide

HP ProLiant DL60 Gen9 Maintenance and service guide

DEC

DEC Digital AlphaServer 400 series User information

Tightrope Media Systems

Tightrope Media Systems Cablecast Setup guide

Gateway

Gateway 8300 user guide

Fujitsu

Fujitsu PRIMERGY BX620 S4 user guide

Sun Microsystems

Sun Microsystems Technical Compute Farm Read me first

Lenovo

Lenovo ThinkServer RD210 Informacije o garanciji in podpori

Supero

Supero SC503-200B user manual

Fujitsu

Fujitsu PRIMERGY TX100 S2 operating manual

Dell EMC

Dell EMC PowerEdge R6525 Installation and service manual

Supero

Supero SC836TQ-R800V(B) user manual

Inspur

Inspur NF3120M5 installation guide

PRG

PRG MBOX EXTREME user manual

Asus AP2400R-E2 User manual

Popular Server manuals by other brands