Asus RS300-E10-PS4 User manual

1U Rackmount Server
RS300-E10-PS4
RS300-E10-RS4
User Guide

ii
Copyright © 2018 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no
event shall ASUS, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental,
or consequential damages (including damages for loss of prots, loss of business, loss of use or data,
interruption of business and the like), even if ASUS has been advised of the possibility of such damages
arising from any defect or error in this manual or product.
Specications and information contained in this manual are furnished for informational use only, and are
subject to change at any time without notice, and should not be construed as a commitment by ASUS.
ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,
including the products and software described in it.
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
E14054
First Edition
July 2018

iii
Contents
Safety information..................................................................................................... vii
About this guide....................................................................................................... viii
Chapter 1: Product Introduction
1.1 System package contents.........................................................................1-2
1.2 Serial number label....................................................................................1-3
1.3 System specifications ...............................................................................1-4
1.4 Front panel features...................................................................................1-6
1.5 Rear panel features....................................................................................1-6
1.6 Internal features .........................................................................................1-7
1.7 LED information .........................................................................................1-9
1.7.1 Front panel LEDs ........................................................................ 1-9
1.7.2 LAN (RJ-45) LEDs .................................................................... 1-10
1.7.3 HDD status LED........................................................................ 1-10
Chapter 2: Hardware Information
2.1 Chassis cover.............................................................................................2-2
2.2 Central Processing Unit (CPU) ................................................................. 2-3
2.2.1 Installing the CPU ....................................................................... 2-3
2.2.2 Installing the CPU heatsink and airduct ...................................... 2-6
2.3 System memory .........................................................................................2-8
2.3.1 Overview ..................................................................................... 2-8
2.3.2 Memory congurations................................................................ 2-8
2.3.3 Installing a DIMM on a single clip DIMM socket.......................... 2-9
2.4 Hard disk drives .......................................................................................2-10
2.5 Expansion slot..........................................................................................2-14
2.5.1 Installing an expansion card to the PCIE1 slot.......................... 2-14
2.5.2 Installing a standard GPU card to the PCIE1 slot ..................... 2-15
2.5.3 Installing a large GPU card to the PCIE1 slot ........................... 2-17
2.5.4 Conguring an expansion card ................................................. 2-18
2.5.5 Installing M.2 (NGFF) cards...................................................... 2-20
2.6 Cable connections ...................................................................................2-21
2.7 SATA/SAS backplane cabling.................................................................2-22
2.8 Removable/Optional components.......................................................... 2-23
2.8.1 System fans .............................................................................. 2-23
2.8.2 Installing ASUS PIKE II RAID card (optional) ........................... 2-24
2.8.3 Redundant power supply module.............................................. 2-26
2.8.4 Installing the Baseboard Management Card (optional)............. 2-27

iv
Contents
2.8.5 Installing the SSD cage............................................................. 2-28
2.8.6 Replacing optical drive (optional).............................................. 2-30
Chapter 3: Installation Options
3.1 Rail kit installation .....................................................................................3-2
3.1.1 Tool-less Friction Rail Kit ............................................................ 3-2
3.1.2 Installing the tool-less rack rail.................................................... 3-2
3.2 Rail kit dimensions ....................................................................................3-5
Chapter 4: Motherboard Information
4.1 Motherboard layout....................................................................................4-2
4.2 Jumpers ......................................................................................................4-4
4.3 Onboard LEDs............................................................................................4-9
4.4 Internal connectors.................................................................................. 4-12
Chapter 5: BIOS Setup
5.1 Managing and updating your BIOS .......................................................... 5-2
5.1.1 ASUS CrashFree BIOS 3 utility................................................... 5-2
5.1.2 ASUS EZ Flash Utility ................................................................. 5-3
5.1.3 BUPDATER utility ....................................................................... 5-4
5.2 BIOS setup program .................................................................................. 5-6
5.2.1 BIOS menu screen...................................................................... 5-7
5.2.2 Menu bar..................................................................................... 5-7
5.2.3 Menu items.................................................................................. 5-8
5.2.4 Submenu items ........................................................................... 5-8
5.2.5 Navigation keys........................................................................... 5-8
5.2.6 General help................................................................................ 5-8
5.2.7 Conguration elds ..................................................................... 5-8
5.2.8 Pop-up window............................................................................ 5-8
5.2.9 Scroll bar..................................................................................... 5-8
5.3 Main menu ..................................................................................................5-9
5.4 Advanced menu .......................................................................................5-10
5.4.1 CPU Conguration .................................................................... 5-11
5.4.2 Power & Performance............................................................... 5-13
5.4.3 Server ME Conguration........................................................... 5-14
5.4.4 Trusted Computing.................................................................... 5-15
5.4.5 APM Conguration.................................................................... 5-15
5.4.6 Runtime Error Logging Settings................................................ 5-15

v
Contents
5.4.7 Onboard LAN Conguration...................................................... 5-16
5.4.8 Serial Port Console Redirection................................................ 5-17
5.4.9 Intel TXT Information.................................................................5-19
5.4.10 PCI Subsystem Settings ........................................................... 5-20
5.4.11 USB Conguration .................................................................... 5-20
5.4.12 Network Stack Conguration..................................................... 5-22
5.4.13 CSM Conguration.................................................................... 5-23
5.4.14 NVMe Conguration.................................................................. 5-24
5.4.15 WHEA Conguration................................................................. 5-24
5.4.16 iSCSI Conguration .................................................................. 5-25
5.4.17 Tls Auth Conguration............................................................... 5-25
5.5 Chipset menu ...........................................................................................5-26
5.5.1 System Agent (SA) Conguration ............................................. 5-26
5.5.2 PCH-IO Conguration ............................................................... 5-30
5.6 Security menu ..........................................................................................5-32
5.7 Boot menu ................................................................................................5-35
5.8 Monitor menu ...........................................................................................5-37
5.9 Tool menu.................................................................................................5-38
5.10 Event Logs menu ..................................................................................... 5-38
5.10.1 Change Smbios Event Log Settings ......................................... 5-38
5.10.2 View Smbios Event Log ............................................................ 5-39
5.11 Server Mgmt menu................................................................................... 5-40
5.11.1 System Event Log..................................................................... 5-41
5.11.2 Bmc self test log........................................................................ 5-42
5.11.3 BMC network conguration....................................................... 5-43
5.11.4 View System Event Log ............................................................ 5-44
5.11.3 BMC User Settings.................................................................... 5-44
5.12 Save & Exit menu.....................................................................................5-45
Chapter 6: RAID Configuration
6.1 Setting up RAID.......................................................................................... 6-2
6.1.1 RAID denitions .......................................................................... 6-2
6.1.2 Installing hard disk drives............................................................ 6-3
6.1.3 Setting the RAID item in BIOS .................................................... 6-3

vi
Contents
6.2 Intel®Rapid Storage Technology enterprise
SATA Option ROM Utility........................................................................... 6-4
6.2.1 Creating a RAID set .................................................................... 6-5
6.2.2 Deleting a RAID set..................................................................... 6-7
6.2.3 Resetting disks to Non-RAID ...................................................... 6-8
6.2.4 Exiting the Intel®Rapid Storage Technology enterprise
SATA Option ROM utility............................................................. 6-9
6.2.5 Rebuilding the RAID.................................................................... 6-9
6.2.6 Setting the Boot array in the BIOS Setup Utility........................ 6-11
6.3 Intel®Rapid Storage Technology enterprise (Windows)...................... 6-12
6.3.1 Creating a RAID set .................................................................. 6-13
6.3.2 Changing a Volume Type.......................................................... 6-15
6.3.3 Deleting a volume ..................................................................... 6-16
6.3.4 Preferences............................................................................... 6-17
Chapter 7: Driver Installation
7.1 RAID driver installation .............................................................................7-2
7.1.1 Creating a USB ash drive with RAID drive................................ 7-2
7.1.2 Installing the RAID controller driver............................................. 7-2
7.2 Management applications and utilities installation ................................ 7-5
7.3 Running the Support DVD......................................................................... 7-5
7.4 Installing the system drivers.....................................................................7-6
Appendix
P11C-C/4L/SYS block diagram .............................................................................. A-2
Q-Code table............................................................................................................ A-3
Notices .................................................................................................................... A-6
REACH ....................................................................................................A-7
Australia statement notice............................................................................A-7
ASUS contact information...................................................................................... A-8

vii
Safety information
Electrical Safety
• Before installing or removing signal cables, ensure that the power cables for the system
unit and all attached devices are unplugged.
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
• When adding or removing any additional devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are connected. If
possible, disconnect all power cables from the existing system before you add a device.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your dealer.
Operation Safety
• Any mechanical operation on this server must be conducted by certied or experienced
engineers.
• Before operating the server, carefully read all the manuals included with the server
package.
• Before using the server, ensure all cables are correctly connected and the power cables
are not damaged. If any damage is detected, contact your dealer as soon as possible.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving or carrying
the system.
This product is equipped with a three-wire power cable and plug for the user’s safety. Use
the power cable with a properly grounded electrical outlet to avoid electrical shock.
CLASS 1 LASER PRODUCT

viii
About this guide
Audience
This user guide is intended for system integrators, and experienced users with at least basic
knowledge of conguring a server.
Contents
This guide contains the following parts:
1. Chapter 1: Product Introduction
This chapter describes the general features of the server, including sections on front
panel and rear panel specications.
2. Chapter 2: Hardware Setup
This chapter lists the hardware setup procedures that you have to perform when
installing or removing system components.
3. Chapter 3: Installation Options
This chapter describes how to install optional components into the barebone server.
4. Chapter 4: Motherboard Information
This chapter gives information about the motherboard that comes with the server. This
chapter includes the motherboard layout, jumper settings, and connector locations.
5. Chapter 5: BIOS Setup
This chapter tells how to change system settings through the BIOS Setup menus and
describes the BIOS parameters.
6. Chapter 6: RAID Configuration
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
7 Chapter 7: Driver Installation
This chapter provides instructions for installing the necessary drivers for different
system components.

ix
Conventions
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
Typography
Bold text Indicates a menu or an item to select.
Italics Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than
sign means that you must press the enclosed key.
Example: <Enter> means that you must press
the Enter or Return key.
<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously,
the key names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<Del>
Command Means that you must type the command
exactly as shown, then supply the required
item or value enclosed in brackets.
Example: At the DOS prompt, type the
command line: format A:/S
DANGER/WARNING: Information to prevent injury to yourself when
trying to complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
NOTE: Tips and additional information to help you complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
References
Refer to the following sources for additional information, and for product and software
updates.
1. ASUS Control Center (ACC) user guide
This manual tells how to set up and use the proprietary ASUS server management
utility.
2. ASUS websites
The ASUS websites worldwide provide updated information for all ASUS hardware and
software products. Refer to the ASUS contact information.

x

This chapter describes the general features of the chassis kit. It
includes sections on front panel and rear panel specications.
1
Product Introduction
Chapter 1: Product Introduction

Chapter 1: Product Introduction
1-2
If any of the above items is damaged or missing, contact your retailer.
1.1 System package contents
Check your system package for the following items.
Model Name RS300-E10-PS4, RS300-E10-RS4
Chassis ASUS R10E 1U Rackmount Chassis
Motherboard ASUS P11C-C/4L/SYS Server Board
Component
1 x 400W Single Power Supply (RS300-E10-PS4)
1+1 450W Redundant Power Supply (RS300-E10-RS4)
4 x Hot-swap 3.5” HDD trays
1 x miniSAS HD to miniSAS HD cable
1 x SAS/SATA Backplane
1 x PCI Express Riser Card
1 x Front I/O Board
4 x System Fans (40 mm x 28 mm)
Accessories
1 x RS300-E10 Series Support DVD (with User’s Guide)
1 x Bag of Screws
1 x AC Power Cable (RS300-E10-PS4)
2 x AC Power Cable (RS300-E10-RS4)
1 x CPU Heatsink
Optional Items
ASUS PIKE II 3008 card
ASUS PIKE II 3108 card
ASUS ASMB9-iKVM Remote management card
Slim-type DVD-ROM/DVD-RW
Second 450W Redundant Power Supply Module (RS300-E10-RS4)
Friction Rail Kit
Single power supply module
GPU Card

ASUS RS300-E10 Series 1-3
4 3 2 1
1.2 Serial number label
Before requesting support from the ASUS Technical Support team, you must take note of the
product’s serial number containing 12 characters such as xxS0xxxxxxxx shown as the gure
below. With the correct serial number of the product, ASUS Technical Support team members
can then offer a quicker and satisfying solution to your problems.
xxS0xxxxxxxx
RS300-E10-RS4
4 3 2 1
xxS0xxxxxxxx
RS300-E10-PS4

Chapter 1: Product Introduction
1-4
1.3 System specifications
The ASUS RS300-E10 Series is a 1U barebone server system featuring the ASUS P11C-
C/4L/SYS Server Board. The server supports Intel®LGA1151 Intel®Xeon®E-21XXX
Processor plus other latest technologies through the chipsets onboard.
(continued on the next page)
Model Name RS300-E10-RS4 RS300-E10-PS4
Processor / System Bus
1 x Socket LGA1151
Intel®Xeon®processor E-21xxx product family
Intel®Core™ i3 processors
Intel®Pentium™ processors
Intel®Celeron™ processors
Core Logic Intel®C242 Chipset
Memory
Total Slots 4 (2 Channels)
Capacity Maximum up to 64GB (UDIMM)
Memory Type DDR4 2666 / 2400 ECC / non-ECC UDIMM
* Refer to ASUS server AVL for the latest update
Memory Size 16GB, 8GB, 4GB (UDIMM)
* Refer to ASUS server AVL for the latest update
Expansion
Slots
Total PCI/PCI-X /
PCI-E Slots 2
Slot Type 1 x PCI-E x16 (x8 Gen3 Link)
1 x PCI-E x8 (x8 Gen3 Link)
Disk
Controller
SATA Controller
Intel®C242
6 x SATA 6Gb/s ports (4 by miniSAS HD) with 2 x M.2 (NGFF
22110/2280/2260/2242, PCI-E NGFF1 x2 link, NGFF2 x1 link
or SATA signal, gray SATA port will disabled when M.2 is SATA
signal)
Intel®RSTe (Windows & Linux)
(Supports software RAID 0, 1, 10, & 5)
SAS Controller
Optional:
ASUS PIKE II 3008-8i 8-port SAS 12G RAID card
ASUS PIKE II 3108-8i 16-port SAS 12G HW RAID card
ASUS PIKE II 3108-8i 16-port 2G SAS 12G HW RAID card
Storage
Bays
I = internal
A or S will be hot-
swappable
4 x 3.5” Hot-Swap HDD Bays
2 x 2.5” Internal SSD Bays
2 x M.2 (NGFF 22110/2280/2260/2242)
Networking LAN 4 x Intel®I210AT + 1 x Mgmt LAN
Graphic VGA Aspeed AST2500 32MB
Auxiliary Storage Device Bay
(Floppy / Optical Drive)
1 x Slim-type Optical Drive Bay
Options: No Device / DVD-RW / DVD ROM
Front I/O Ports 2 x USB 3.0 ports
1 x VGA port

ASUS RS300-E10 Series 1-5
*Specifications are subject to change without notice.
Model Name RS300-E10-RS4 RS300-E10-PS4
Rear I/O Ports
2 x USB 3.1 ports
2 x USB 3.0 ports
1 x VGA port
1 x External Serial Port
4 x RJ-45 ports
1 x RJ-45 port (One for ASMB9-iKVM) (Optional)
Switch/LED
Rear Switch/LED:
1 x Q-Code/Port 80 LED
1 x Power switch
Front Switch/LED:
1 x Power switch/LED
1 x Location switch/LED
1 x Reset switch
1 x HDD Access LED
1 x Message LED
LAN 1-4 LED
OS Support
Windows®Server 2016
RedHat®Enterprise Linux
SuSE®Linux Enterprise Server
CentOS
VMware
Citrix XenServer
* Refer to http://www.asus.com/ for the latest OS support.
Management
Solution
Software ASUS Control Center
Out of Band
Remote
Management
Optional ASMB9-iKVM for KVM-over-IP
Regulatory Compliance BSMI, CE, C-TICK, FCC, CCC (Class A)
Dimension (HH x WW x DD) 615mm x 444mm x 44mm (1U)
(24.21” x 17.48” x 1.73”)
Net Weight Kg (CPU, DRAM &
HDD not included) 18.99 Kg 17.16 Kg
Power Supply
(following different
configuration by region)
1+1 Redundant 450W 80 PLUS
Gold Power Supply
Rating: 100-127/200-240Vac,
5.5A/3A (for each inlet), 50-60Hz,
Class 1
Single 400W 80 PLUS Gold
Power Supply
Rating: 100-240Vac, 6A-3A 50-
60Hz, Class 1
Environment
Operating temperature: 10°C ~ 35°C
Non operating temperature: -40°C ~ 70°C
Non operating humidity: 20% ~ 90% ( Non condensing)

Chapter 1: Product Introduction
1-6
1.4 Front panel features
The barebone server displays a simple yet stylish front panel with easily accessible features.
The power and reset buttons, LED indicators, slim type optical drive, and two USB ports are
located on the front panel.
Refer to the Front panel LEDs section for the LED descriptions.
1.5 Rear panel features
The rear panel includes the expansion slots, system power socket, and rear fans. The middle
part includes the I/O shield with openings for the rear panel connectors on the motherboard.
4 3 2 1
Optical drive (optional) Asset tag
Rack screw Rack screw
USB 3.0 ports
VGA port
LAN 2 LED
LAN 1 LED
LAN 4 LED
LAN 3 LED
Message LED
Power button
Location switch
Reset button
HDD LED
HDD 1 HDD 2 HDD 3 HDD 4
*This port is for ASUS ASMB9-iKVM controller card only.
RS300-E10-RS4
RS300-E10-PS4
VGA port
VGA port
USB 3.0 ports
USB 3.0 ports
USB 3.1 ports
USB 3.1 ports
LAN port for iKVM*
LAN port for iKVM*
Gigabit LAN port 3
Gigabit LAN port 3
Gigabit LAN port 4
Gigabit LAN port 4
Gigabit LAN port 1
Gigabit LAN port 1
Gigabit LAN port 2
Gigabit LAN port 2
Message LED
Message LED
Power button
Power button
Q-Code LED
Q-Code LED
Power cord connector and
Redundant power supply
Power cord connector
and power supply

ASUS RS300-E10 Series 1-7
RS300-E10-RS4
1.6 Internal features
The barebone server includes the basic components as shown.
The barebone server does not include a oppy disk drive. Connect a USB oppy disk drive
to any of the USB ports on the front or rear panel if you need to use a oppy disk.
WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
1. 1+1 Redundant 450W 80
PLUS Gold Power Supply
2. PCI Express slot Riser
Card
3. ASUS P11C-C/4L/SYS
Server Board
4. System fans
5. SAS / SATA backplane
(hidden)
6. HDD tray 1-4
7. Front I/O boards (hidden)
8. Slim-type optical drive
9. SSD Cage
10. Asset Tag
Turn off the system power and detach the power supply before removing or replacing any
system component.

Chapter 1: Product Introduction
1-8
The barebone server does not include a oppy disk drive. Connect a USB oppy disk drive
to any of the USB ports on the front or rear panel if you need to use a oppy disk.
WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
1. Single 400W 80 PLUS
Gold Power Supply
2. PCI Express slot Riser
Card
3. ASUS P11C-C/4L/SYS
Server Board
4. System fans
5. SAS / SATA backplane
(hidden)
6. HDD tray 1-4
7. Front I/O boards (hidden)
8. Slim-type optical drive
9. SSD Cage
10. Asset Tag
Turn off the system power and detach the power supply before removing or replacing any
system component.
RS300-E10-PS4

ASUS RS300-E10 Series 1-9
1.7 LED information
1.7.1 Front panel LEDs
LED Icon Display status Description
Power LED ON System power ON
HDD Access LED OFF
Blinking
No activity
Read/write data into the HDD
Message LED OFF
ON
System is normal; no incoming event
A hardware monitor event is indicated
Location LED
OFF
ON
Normal status
Location switch is pressed
(Press the location switch again to turn off)
LAN LEDs
OFF
Blinking
ON
No LAN connection
LAN is transmitting or receiving data
LAN connection is present
4 3 2 1
LAN 2 LED
LAN 1 LED
LAN 4 LED
LAN 3 LED
HDD LED
Power button
Location switch
Message LED

Chapter 1: Product Introduction
1-10
1.7.3 HDD status LED
4 3 2 1
HDD status LED
SATA/SAS HDD LED Description
HDD Status
LED
GREEN ON SATA/SAS HDD power ON
RED ON HDD has failed and should be swapped
immediately
GREEN/
RED Blinking RAID rebuilding
GREEN/
RED OFF HDD not found
HDD Activity
LED GREEN Blinking Read/write data from/into the SATA/SAS HDD
HDD Activity LED
1.7.2 LAN (RJ-45) LEDs
LAN port LED indications
LAN port
SPEED
LED
ACT/LINK
LED
Activity/Link LED Speed LED
Status Description Status Description
OFF No link OFF 10 Mbps connection
GREEN Linked YELLOW 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
Dedicated Management LAN port (DM_LAN1) LED indications
DM LAN port
Activity/Link LED Speed LED
Status Description Status Description
OFF No link OFF 10 Mbps connection
YELLOW Linked ORANGE 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
SPEED
LED
ACT/LINK
LED