Asus TS700-E8-PS4 User manual

Server User Guide
TS700-E8-PS4
TS700-E8-RS8

ii
Copyright © 2014 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no
event shall ASUS, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental,
or consequential damages (including damages for loss of prots, loss of business, loss of use or data,
interruption of business and the like), even if ASUS has been advised of the possibility of such damages
arising from any defect or error in this manual or product.
Specications and information contained in this manual ae furnished for informational use only, and are
subject to change at any time without notice, and should not be construed as a commitment by ASUS.
ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,
including the products and software described in it.
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
E9851b
Second Edition
December 2014

iii
Contents
Notices ...................................................................................................................... vii
Safety information.................................................................................................... viii
About this guide.......................................................................................................... x
Chapter 1: Product Introduction
1.1 System package contents.........................................................................1-2
1.2 Serial number label....................................................................................1-3
1.3 System specifications ...............................................................................1-4
1.4 Front panel features...................................................................................1-6
1.5 Rear panel features....................................................................................1-7
1.6 Internal features .........................................................................................1-9
1.7 LED information .......................................................................................1-10
1.7.1 Front panel LEDs ...................................................................... 1-10
1.7.2 LAN (RJ-45) LEDs .................................................................... 1-11
Chapter 2: Hardware Information
2.1 Chassis cover.............................................................................................2-2
2.1.1 Removing the side cover............................................................. 2-2
2.1.2 Reinstalling the side cover .......................................................... 2-3
2.2 Central Processing Unit (CPU) ................................................................. 2-4
2.2.1 Installing the CPU ....................................................................... 2-4
2.2.2 Installing the CPU heatsink......................................................... 2-9
2.3 System memory .......................................................................................2-10
2.3.1 Overview ................................................................................... 2-10
2.3.2 Memory Congurations............................................................. 2-10
2.3.3 Installing a DIMM on a single clip DIMM socket........................ 2-12
2.3.4 Removing a DIMM from a single clip DIMM socket .................. 2-12
2.4 Front panel assembly ..............................................................................2-13
2.4.1 Removing the front panel assembly.......................................... 2-13
2.4.2 Reinstalling the front panel assembly ....................................... 2-13
2.5 SATA/SAS hard disk drives ....................................................................2-14
2.5.1 Removing the HDD module cage.............................................. 2-14
2.5.2 Installing the HDD module cage................................................ 2-15
2.5.3 Removing the backplane........................................................... 2-16
2.5.4 Installing a hot-swap SATA/SAS hard disk drive ...................... 2-16
2.5.5 Installing a 2.5-inch hard disk drive (TS700-E8-RS8 only) ....... 2-18
2.6 5.25-inch or 3.5-inch drives.....................................................................2-20
2.6.1 Installing a 5.25-inch drive ........................................................ 2-20
2.7 Expansion slots........................................................................................2-21
2.7.1 Installing an expansion card...................................................... 2-21
2.7.2 Conguring an expansion card ................................................. 2-23

iv
Contents
2.7.3 Installing an M.2 expansion card............................................... 2-25
2.8 Cable connections ...................................................................................2-26
2.8.1 Motherboard connections.......................................................... 2-26
2.8.2 SATA/SAS backplane cabling................................................... 2-27
2.9 Removable components..........................................................................2-29
2.9.1 System fans .............................................................................. 2-29
2.9.2 Redundant power supply module (TS700-E8-RS8 only) .......... 2-31
2.9.3 Chassis footpads....................................................................... 2-32
Chapter 3: Installation Options
3.1 Preparing the system for rack mounting.................................................3-2
3.2 Attaching the inner rail to the server ....................................................... 3-2
3.3 Attaching the rails to the rack ..................................................................3-3
3.4 Mounting the server to the rack ...............................................................3-4
Chapter 4: Motherboard Info
4.1 Motherboard layout....................................................................................4-2
4.2 Onboard LEDs............................................................................................4-4
4.3 Onboard buttons, switches and jumpers .............................................. 4-12
4.3.1 Onboard buttons and switches.................................................. 4-12
4.3.2 Jumpers .................................................................................... 4-14
4.4 Internal connectors..................................................................................4-18
Chapter 5: BIOS setup
5.1 Managing and updating your BIOS .......................................................... 5-2
5.1.1 ASUS CrashFree BIOS 3 utility................................................... 5-2
5.1.2 ASUS EZ Flash Utility ................................................................. 5-3
5.1.3 BUPDATER utility ....................................................................... 5-4
5.2 BIOS setup program ..................................................................................5-6
5.2.1 BIOS menu screen...................................................................... 5-7
5.2.2 Menu bar..................................................................................... 5-7
5.2.3 Menu items.................................................................................. 5-8
5.2.4 Submenu items ........................................................................... 5-8
5.2.5 Navigation keys........................................................................... 5-8
5.2.6 General help................................................................................ 5-8
5.2.7 Conguration elds ..................................................................... 5-8
5.2.8 Pop-up window............................................................................ 5-8
5.2.9 Scroll bar..................................................................................... 5-8
5.3 Main menu ..................................................................................................5-9
5.3.1 System Date [Day xx/xx/xxxx]..................................................... 5-9
5.3.2 System Time [xx:xx:xx] ............................................................... 5-9

v
Contents
5.4 AiTweaker menu.......................................................................................5-10
5.5 Advanced menu .......................................................................................5-13
5.5.1 ACPI Settings............................................................................ 5-14
5.5.2 Smart Settings........................................................................... 5-14
5.5.3 NCT6779D Super IO Conguration .......................................... 5-15
5.5.4 Onboard LAN I210 Conguration ............................................. 5-16
5.5.5 Serial Port Console Redirection................................................ 5-17
5.5.6 APM .......................................................................................... 5-20
5.5.7 Advance Power Management Conguration............................. 5-21
5.5.8 PCI Subsystem Settings ........................................................... 5-22
5.5.9 Network Stack Conguration..................................................... 5-23
5.5.10 CSM Conguration.................................................................... 5-24
5.5.11 Trusted Computing.................................................................... 5-25
5.5.12 USB Conguration .................................................................... 5-26
5.5.13 iSCSI Conguration................................................................... 5-27
5.6 IntelRCSetup menu.................................................................................. 5-28
5.6.1 Processor Conguration............................................................ 5-29
5.6.2 Advanced Power Management Conguration........................... 5-31
5.6.3 Common RefCode Conguration.............................................. 5-32
5.6.4 QPI Conguration...................................................................... 5-33
5.6.5 Memory Conguration............................................................... 5-34
5.6.6 IIO Conguration....................................................................... 5-37
5.6.7 PCH Conguration .................................................................... 5-38
5.6.8 Miscellaneous Conguration..................................................... 5-42
5.6.9 Server ME Conguration........................................................... 5-43
5.6.10 Runtime Error Logging Support ................................................ 5-43
5.7 Server Mgmt menu...................................................................................5-44
5.8 Event Logs menu .....................................................................................5-48
5.8.1 Change Smbios Event Log Settings ......................................... 5-48
5.8.2 View Smbios Event Log ............................................................ 5-49
5.9 Monitor menu ...........................................................................................5-50
5.10 Security menu ..........................................................................................5-51
5.11 Boot menu ................................................................................................5-54
5.12 Tool menu.................................................................................................5-55
5.13 Exit menu..................................................................................................5-56
Chapter 6: RAID Configuration
6.1 Setting up RAID.......................................................................................... 6-2
6.1.1 RAID denitions .......................................................................... 6-2
6.1.2 Installing hard disk drives............................................................ 6-3

vi
Contents
6.1.3 Setting the RAID item in BIOS .................................................... 6-3
6.1.4 RAID conguration utilities.......................................................... 6-3
6.2 LSI Software RAID Configuration Utility .................................................6-4
6.2.1 Creating a RAID set .................................................................... 6-5
6.2.2 Adding or viewing a RAID conguration.................................... 6-11
6.2.3 Initializing the virtual drives ....................................................... 6-12
6.2.4 Rebuilding failed drives............................................................. 6-16
6.2.5 Checking the drives for data consistency.................................. 6-18
6.2.6 Deleting a RAID conguration................................................... 6-21
6.2.7 Selecting the boot drive from a RAID set.................................. 6-22
6.2.8 Enabling WriteCache ................................................................ 6-23
6.3 Intel®Rapid Storage Technology enterprise SATA/SSATA Option
ROM Utility................................................................................................6-24
6.3.1 Creating a RAID set .................................................................. 6-25
6.3.2 Deleting a RAID set................................................................... 6-27
6.3.3 Resetting disks to Non-RAID .................................................... 6-28
6.3.4 Exiting the Intel®Rapid Storage Technology enterprise
SATA/SSATA Option ROM utility.............................................. 6-29
6.3.5 Rebuilding the RAID.................................................................. 6-29
6.3.6 Setting the Boot array in the BIOS Setup Utility........................ 6-31
6.4 Intel®Rapid Storage Technology enterprise (Windows)...................... 6-32
6.4.1 Creating a RAID set .................................................................. 6-33
6.4.2 Changing a Volume Type.......................................................... 6-35
6.4.3 Deleting a volume ..................................................................... 6-36
6.4.4 Preferences............................................................................... 6-37
Chapter 7: Driver installation
7.1 RAID driver installation .............................................................................7-2
7.1.1 Creating a RAID driver disk......................................................... 7-2
7.1.2 Installing the RAID controller driver............................................. 7-3
7.2 Software drivers and utilities installation.............................................. 7-13
7.3 Running the Support DVD ......................................................................7-13
7.4 Installing the drivers and utilities ..........................................................7-16
7.4.1 Using the ASUS InstAll application ........................................... 7-16
7.4.2 Installing a driver or utility.......................................................... 7-18
7.5 Running the utilities.................................................................................7-20
7.5.1 USB Charger+........................................................................... 7-20
Appendix A: Reference Information
Z10PE-D16 WS block diagram ............................................................................... A-2
ASUS contact information...................................................................................... A-3

vii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
This Class A digital apparatus complies with Canadian ICES-003.
WARNING! The use of shielded cables for connection of the monitor to the graphics card
is required to assure compliance with FCC regulations. Changes or modications to this
unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of
Chemicals) regulatory framework, we publish the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.

viii
Safety information
Electrical Safety
• Before installing or removing signal cables, ensure that the power cables for the system
unit and all attached devices are unplugged.
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
• When adding or removing any additional devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are connected. If
possible, disconnect all power cables from the existing system before you add a device.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your dealer.
Operation Safety
• Any mechanical operation on this server must be conducted by certied or experienced
engineers.
• Before operating the server, carefully read all the manuals included with the server
package.
• Before using the server, ensure all cables are correctly connected and the power cables
are not damaged. If any damage is detected, contact your dealer as soon as possible.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving or carrying
the system.
This product is equipped with a three-wire power cable and plug for the user’s safety. Use
the power cable with a properly grounded electrical outlet to avoid electrical shock.

ix
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
Australia statement notice
From 1 January 2012 updated warranties apply to all ASUS products, consistent with
the Australian Consumer Law. For the latest product warranty details please visit http://
support.asus.com. Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at
http://support.asus.com

x
About this guide
Audience
This user guide is intended for system integrators, and experienced users with at least basic
knowledge of conguring a server.
Contents
This guide contains the following parts:
1. Chapter 1: Product introduction
This chapter describes the general features of the server, including sections on front
panel and rear panel specications.
2. Chapter 2: Hardware setup
This chapter lists the hardware setup procedures that you have to perform when
installing or removing system components.
3. Chapter 3: Installation options
This chapter describes how to install optional components into the barebone server.
4. Chapter 4: Motherboard information
This chapter gives information about the motherboard that comes with the server. This
chapter includes the motherboard layout, jumper settings, and connector locations.
5. Chapter 5: BIOS information
This chapter tells how to change system settings through the BIOS Setup menus and
describes the BIOS parameters.
6. Chapter 6: RAID configuration
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
7 Chapter 7: Driver installation
This chapter provides instructions for installing the necessary drivers for different
system components.

xi
References
Refer to the following sources for additional information, and for product and software
updates.
1. ASUS Server Web-based Management (ASWM) user guide
This manual tells how to set up and use the proprietary ASUS server management
utility.
2. ASUS websites
The ASUS websites worldwide provide updated information for all ASUS hardware and
software products. Refer to the ASUS contact information.
Conventions
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
Typography
Bold text Indicates a menu or an item to select.
Italics Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than
sign means that you must press the enclosed key.
Example: <Enter> means that you must press
the Enter or Return key.
<Key1>+<Key2+<Key3> If you must press two or more keys simultaneously,
the key names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<Del>
Command Means that you must type the command
exactly as shown, then supply the required
item or value enclosed in brackets.
Example: At the DOS prompt, type the
command line: format A:/S
DANGER/WARNING: Information to prevent injury to yourself when
trying to complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
NOTE: Tips and additional information to help you complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.

xii

1
Product introduction
This chapter describes the motherboard features and the new
technologies it supports.
Chapter 1: Product Introduction

Chapter 1: Product introduction
1-2
* Six hot-swap 3.5-inch HDDs are supported by default. Upgrade the optional PIKE card before using eight hot-swap
3.5-inch HDDs.
** ASUS System Web-based Management
If any of the above items is damaged or missing, contact your retailer.
1.1 System package contents
Check your system package for the following items.
Model Name TS700-E8-PS4, TS700-E8-RS8
Chassis ASUS T50A Pedestal / 5U Rackmount Chassis
Motherboard ASUS Z10PE-D16 WS Server Board
Component
1 x 1200W 80PLUS Platinum Single Power Supply Module (TS700-E8-PS4)
1 x 800W 80PLUS Gold Redundant Power Supply Module (TS700-E8-RS8)
4 x Hot-swap 3.5-inch HDD Trays (Front panel, TS700-E8-PS4)
8 x Hot-swap 3.5-inch HDD Trays (Front panel, TS700-E8-RS8)*
2 x Hot-swap 2.5-inch SSD Trays (Rear panel, TS700-E8-RS8 only)
1 x SAS/SATA backplane (TS700-E8-PS4)
2 x SAS/SATA backplanes (TS700-E8-RS8)
1 x Front I/O Board
3 x System Fans (Front: 2 x 80mm x 38mm; Rear: 1 x 120mm x 38mm)
Accessories
1 x Support DVD (including the User Guide)
1 x ASWM** Enterprise DVD
1 x ASMB8 DVD
1 x Bag of Screws
1 x AC Power Cable (TS700-E8-PS4)
2 x AC Power Cables (TS700-E8-RS8)
2 x CPU Heatsinks
Optional
Items
1 x Second 800W 80PLUS Gold Redundant Power Supply Module (TS700-
E8-RS8)
1 x DVD-ROM / DVD-RW
1 x ASUS TS700-E8-PS4, TS700-E8-RS8 Rackmount Rail Kit
1 x ASUS PIKE RAID Card

ASUS TS700-E8-PS4, TS700-E8-RS8 1-3
1.2 Serial number label
Before requesting support from the ASUS Technical Support team, you must take note of
the product’s serial number containing 14 characters such as xxS0xxxxxxxxxx shown as the
gure below. With the correct serial number of the product, ASUS Technical Support team
members can then offer a quicker and satisfying solution to your problems.
xxS0xxxxxxxxxx
TS700-E8-PS4
xxS0xxxxxxxxxx
TS700-E8-RS8

Chapter 1: Product introduction
1-4
1.3 Systemspecications
The ASUS TS700-E8-PS4, TS700-E8-RS8 is a Pedestal / 5U Rackmount barebone server
system featuring the ASUS Z10PE-D16 WS Server Board. The server supports Intel®
LGA2011-3 Intel®Xeon®E5-2600 Processor v3 plus other latest technologies through the
chipsets onboard.
(continued on the next page)
Model Name TS700-E8-PS4 TS700-E8-RS8
Processor Support / System
Bus
2 x Socket R3 LGA 2011-3 Intel®Xeon®Processor E5-2600 v3
Family
QPI 6.4 / 8.0 / 9.6GT/s
Core Logic Intel®C612 PCH Chipset
Memory
Total Slots 16 (4 Channels per CPU, 8 DIMMs per CPU)
Capacity Maximum up to 1024 GB
Memory Type DDR4 2133 / 1866 / 1600 / 1333 RDIMM / LR-DIMM/ NVDIMM
Refer to www.asus.com for the latest memory AVL update.
Memory Size
32GB, 16GB, 8GB and 4GB (RDIMM)
64GB, 32GB (LRDIMM)
Refer to www.asus.com for the latest memory AVL update.
Expansion
Slots (follow
SSI Location #)
Total PCI/PCI-E
Slots 6
Slot Type
4 x PCI-E x16 (Gen3 x16 link, Full-height/FL)
1 x PCI-E x16 (Gen3 x8 link, Full-height/FL)
1 x PCI-E x16 (Gen3 x8 link, Full-height/HL)
Storage
SATA Controller
Intel®C612
10 x SATA 6 Gbps ports or
9 x SATA 6 Gbps ports + 1 x discrete M.2 socket
Intel®RSTe (for Windows only; supports software RAID 0, 1, 10
and 5)
LSI®MegaRAID driver supports RAID 0, 1 and 10) (for Linux
and Windows)
SAS Controller RAID card (optional):
ASUS PIKE II 3008 8-port SAS HBA card
HDD Bays
I = internal
A or S = hot-
swappable
4 x Hot-swap 3.5-inch HDD
Bays
8 x Hot-swap 3.5-inch HDD
Bays
* Six hot-swap 3.5-inch HDDs are
supported by default. Upgrade the
optional PIKE card before using
eight hot-swap 3.5-inch HDDs.
2 x Hot-swap 2.5-inch SSD
Bays
Networking LAN 2 x Intel®I210T
1 x Management LAN
Graphic VGA Aspeed AST2400 32MB

ASUS TS700-E8-PS4, TS700-E8-RS8 1-5
*Specifications are subject to change without notice.
Model Name TS700-E8-PS4 TS700-E8-RS8
Auxiliary Storage Device Bay
(Floppy / Optical Drive)
3 x 5.25" media bays
(Options: No Device / DVD-RW)
Onboard I/O Connectors / LED
indicators
1 x PS/2 keyboard/mouse combo port
1 x Q-Code Logger button with LED
1 x BIOS Flashback button with LED
1 x S/PDIF Out port
1 x RJ-45 management port
2 x RJ-45 GbE port
8-channel Audio I/O
4 x USB 3.0 ports
2 x USB 2.0 ports
1 x VGA port
OS Support
Windows®Server 2012 R2
Windows®Server 2012
Windows®Server 2008 R2
RedHat®Enterprise Linux
SuSE®Liunx Enterprise Server
CentOS
Unbuntu
VMWare
Citrix XenServer
* Support versions are subject to change without notice. Refer to
www.asus.com for updates.
Management
Solution
Software ASWM Enterprise
Out of Band
Remote
Management
ASMB8-iKVM for KVM-over-Internet
Dimensions (HH x WW x DD) 455 mm x 217.50 mm x 545.00 mm
Net Weight Kg
(CPU, DRAM & HDD not
included)
20 Kg
Power Supply 1200W 80PLUS Platinum Single
Power Supply Module
800W 80PLUS Gold Redundant
Power Supply Module
Power Rating 100-240Vac, 12-8A, 50-60Hz,
Class I
100-127 / 200-240Vac,
9.9A/4.79A, 47-63Hz, Class I
Environment
Operating temperature: 10°C – 35°C
Non operation temperature: -40°C – 70°C
Non operation humidity: 20% – 90% (Non condensing)

Chapter 1: Product introduction
1-6
1.4 Front panel features
• Refer to the 1.7.1 Front panel LEDs section for the LED descriptions.
• * Only the rst set of 4-bay HDD module is provided on TS700-E8-PS4.
• ** For TS700-E8-RS8, six hot-swap 3.5-inch HDDs are supported by default. Upgrade
the optional PIKE card before using eight hot-swap 3.5-inch HDDs.
LAN port 3 LAN port 1
Q-Code Logger Management
USB BIOS Flashback
SPDIF OUT
USB3.0
USB3.0
side
MIC IN LINEOUT LINE IN
KY
rear c/sub
12
Optical drive (optional)
2 x Empty 5.25-inch
bays
Power button
Reset button
Message LED
HDD access LED
Power LED
2 x USB 2.0 ports
4-bay HDD module
(First set*)
LAN1 LED
LAN2 LED
Location LED
(Reserved)
Security lock
2 x USB 3.0 ports
Headphone jack
Microphone jack
4-bay HDD module
(Second set,
TS700-E8-RS8 only**)

ASUS TS700-E8-PS4, TS700-E8-RS8 1-7
1.5 Rear panel features
* This port is for ASUS ASMB8-iKVM controller and for techincians only.
TS700-E8-PS4
LAN port 3 LAN port 1
Q-Code Logger Management
USB BIOS Flashback
SPDIF OUT
USB3.0
USB3.0
side
MIC IN LINE OUT LINE IN
KY
rear c/sub
12
Power connector
Expansion slots
120mm x 38mm
system fan
PS/2 keyboard/
mouse combo port
4 x USB 3.0 ports
2 x USB 2.0 ports Q-Code Logger
button with LED
BIOS Flashback
button with LED
Management LAN port*
VGA port
SPDIF Out port
2 x USB 2.0 ports
Audio I/O ports
LAN (RJ-45) port 2
LAN (RJ-45) port 1

Chapter 1: Product introduction
1-8
TS700-E8-RS8
LAN port 3 LAN port 1
Q-Code Logger Management
USB BIOS Flashback
SPDIF OUT
USB3.0
USB3.0
side
MIC IN LINE OUT LINE IN
KY
rear c/sub
12
Power connectors
Expansion slots
120mm x 38mm
system fan
PS/2 keyboard/
mouse combo port
4 x USB 3.0 ports
2 x USB 2.0 ports Q-Code Logger
button with LED
BIOS Flashback
button with LED
Management LAN port*
VGA port
SPDIF Out port
2 x USB 2.0 ports
Audio I/O ports
LAN (RJ-45) port 2
LAN (RJ-45) port 1
2 x 2.5-inch SSD bays
* This port is for ASUS ASMB8-iKVM controller and for techincians only.