AT&T 1145 User manual

Quick Start Guide
2.4 GHz Cordless
Telephone [phone]
with Caller ID & Call Waiting
ATT-1445QSG-d02jan12ok.qxd 2/13/1950 7:21 PM Page 1

Installation and setup
Connect the base and install batteries as shown below. After installation, place the
handset in the base and allow the battery to charge for 12 hours before use. You can
keep the battery charged by returning the handset to the base after each use.
Plug power cord
transformer into
electrical outlet.
Plug long line
cord into tele-
phone jack.
NOTE:Use only the
power cord supplied with this
product.If you need a replace-
ment, call 1 800 222–3111.
NOTE: For wall mount-
ing, please see page 8 in your
User Manual.
Rotate antenna to
fully upright
position.
Place handset in base to CHARGE
FOR 12 HOURS before first use.
Plug in battery here.
Press coin into slot on
base of handset to
release latch, then
remove cover.
To replace cover:
1Insert tabs at top of
cover into slots on
base.
2Align tab at bottom
of cover with slot in
base, then press to
click in place.
Charging light
will be illuminat-
ed while battery
is charging.
ATT-1445QSG-d02jan12ok.qxd 2/13/1950 7:21 PM Page 2

Quick reference guide
Select
Press to store a programming
option, or to store a directory
entry in memory.
Off
During a call, press to hang up.
During programming, press to stop
without making changes.
Hold
Press to place a call on hold. Press
again to resume your call.
^V Volume/Function
During a call, press ^V to adjust
listening volume.
While programming, press to change
menu item or value.
Press DIR when phone is not in use to
display phone book entries. While
entering or modifying names, press to
advance cursor.
Press CID when phone is not in use to
display Caller ID information. While
entering numbers or letters, press to
delete last character entered.
Phone/Flash
Press to begin a call, then dial a number.
During a call, press to receive an incom-
ing call, if Call Waiting is activated.
Chan/Delete
If call is noisy or unclear, press
to switch to a clearer channel.
Press and hold to delete all
Caller ID entries.
Prog
Press to customize the telephone’s
operation.
Redial/Pause
Press to redial last number
called.
While dialing or entering num-
bers into your phone directory,
press to insert a 4-second
dialing pause.
Press once to enter “A”
Press twice to enter “B”
Press 3 times to enter “C”
Press 4 times to enter “2”
2
NEW 00 OLD 27
0 8/12 10:06
AM
Date and timeLow battery
Incoming calls
Handset
Using the dial pad to enter letters
ATT-1445QSG-d02jan12ok.qxd 2/13/1950 7:21 PM Page 3

Quick reference guide
Copyright © 2003 Advanced American Telephones. All Rights Reserved.
AT&T and the Globe Design are trademarks of AT&T Corp.,
licensed to Advanced American Telephones.
Telephone Base
ANTENNA
Swivel fully upright
for best results.
PAGE/
HANDSET
LOCATOR
Press to locate hand-
set if lost.
IN USE/CHARGING
Steady: Handset battery is charging.
Flashing: Phone is in use, or call is on
hold.
MESSAGE
Flashes when you have new voice
mail (requires voice mail service from
your local telephone company).
NEW CALL
If you have Caller ID service:
On when new calls have been
received; off when all new Caller ID
records have been reviewed.
ATT-1445QSG-d02jan12ok.qxd 2/13/1950 7:21 PM Page 4