Atdec 8060 User manual

AD-WT-8060 Page 1 of 4
Installation Guide
AD-WT-8060
Tilt Wall Mount 8060
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total
weight of all equipment being mounted.
! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid
electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.
M-C
M6x30
Screw
(x4)
M-B
M6x14
Screw
(x4)
M-D
M8x30
Screw
(x4)
M-A
M5x14
Screw
(x4)
M-F
Multi
Washer
(x4)
M-G
Short
Spacer
(x8)
M-E
M8x50
Screw
(x4)
B
Display Bracket (left)
C
Display Bracket (right)
A
Wall Plate
D
Security Bar
M-H
Long
Spacer
(x8)
E
Hex Key
REQUIRED TOOLS
• Phillips head screwdriver
• Power drill
• Suitable drill bit
• Driver bit for selected
wall fasteners
• Stud nder
• Spirit level
• Socket wrench set
COMPONENT CHECKLIST
0 - 80kg
(0 - 176lb)
WEIGHT RANGE
NOTE:
! Wall Plate Mounting Fasteners are NOT supplied with Wall Mounts.
Professional installer to ensure correct Mounting Fastener type, location &
quantity to suit structure where Wall Mount is installed.
! ALWAYS use a washer between the chosen fastener and the wall plate.
! Mounting fasteners to be used as per manufacturers instructions, including
minimum engagement to achieve necessary performance.

AD-WT-8060 Page 2 of 4
J
G
Slot Dimension
Ø8 x 40mm
12 3
3. Hook and Secure the Display onto the Wall Plate
Max. Ø11 mm
D
NOTE:
Ensure level adjustment
screws are retracted prior
to mounting the display.
3.1. Angle the display and hook the Display
Brackets over the top of the Wall Plate.
This should be completed by two people.
NOTE:
• Choice and supply of appropriate wall plate fasteners is the
responsibility of the installer.
• Consult a preferred fastener supplier or a structural engineer
to select fasteners which are most appropriate for the weight
of the display and wall construction method.
• Wall plate must be level. Verify using a quality spirit level tool.
• On a Stud Wall or Drywall use a good quality Stud Finder to
position mounting fasteners in the centre of studs.
• On a Masonry Wall avoid positioning Wall Plate mounting
fasteners in a mortar join.
M-C (M6x30) /
M-D (M8x30)
M-C (M6x30) /
M-D (M8x30)
M-F
M-G M-G
M-H
M-H
M-G
M-H
M-H M-G
M-H
M-C (M6x30) /
M-D (M8x30)
M-E (M8x50) M-E (M8x50) M-E (M8x50)
M-A (M5x14) /
M-B (M6x14)
M-F M-F M-F
M-F M-F M-F
B
C
M-H (OPTIONAL)
SPACER HEIGHT (mm)
M-G (OPTIONAL)
M-A
M-B
M-C
M-D
M-E
(M5x14)
(M6x14)
(M6x30)
(M8x30)
(M8x50)
M-F
403530
2520
15
10
5
2. Attach the Display Brackets to the Display
3.2. Slide Security Bar Dthrough the slots at the bottom of each
Display Bracket, ensuring the Security Bar sits to the rear of
the Wall Plate and the display cannot be lifted up and off the
Wall Plate.
3.3. (OPTIONAL) To prevent theft of the display, add a padlock to
the end of Security Bar D.
1. Mount the Wall Plate to the Wall
Slot Dimension
Ø9 x 55mm
*Fasteners shown are for example only
NOTE:
• Always use multi-washers M-F.
• Ensure the display brackets are
not loose and screws are not
forced too deep into the display.
• If spacers are needed, use the
shortest possible combination
between the display bracket and
the display.

AD-WT-8060 Page 3 of 4
E
+5° / -10°
Remove the black plastic caps
from Display Brackets Band C.
Tilt the display to the desired
viewing angle and tighten the
nuts using a suitable socket
wrench tool to lock the angle
in place.
NOTE:
Support display whilst adjusting tilt.
NOTE:
Support display whilst turning the level adjustment screws.
Level Adjustment Display Tilt
E
+5° / -10°
ADJUSTMENTS
If needed, carefully turn the
screws at the top of each
display bracket clockwise using
Hex Key Eto level the display.

AD-WT-8060 Page 4 of 4
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20220323