Atdec AWM-LR User manual

AWM-LR Page 1 of 4
Installation Guide
AWM-LR
Dual Crossbar
COMPONENT CHECKLIST
REQUIRED TOOLS
• Phillips Head Screwdriver
A
Crossbar
Assembly
(x1)
B
VESA Plate
(x2)
C
Handle
(x1)
D
Screw
M4x10mm
(x8)
E
Screw
M4x12mm
(x8)
F
Screw
M4x16mm
(x8)
I
Plastic
Washer
(x2)
H
Hole
Cap
(x2)
J
Screw
M6x12mm
(x2)
G
Security
Screw
(x2)
K
4mm
Allen Key
(x1)
L
3mm
Allen Key
(x1)
2 - 7kg
(4.5 - 15lbs)
per monitor
WEIGHT RANGE
Monitor weight should be
within the weight range of
all modular elements that
make up the complete
monitor mounting solution.
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed
the capacity of the mount even though the monitor weight may be within the stated range.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is compatible with AWM Series monitor arm products.

AWM-LR Page 2 of 4
3. Attach VESA plates to monitors
3.2 Ensure suitable screw length is used. 3.3 VESA mounting compatibility
Note: For other sizes, use
a suitable adaptor plate
3.1 Screw VESA plates onto the monitors.
100mm
75mm
100mm 75mm
1. Mount crossbar onto arm
2. Attach handle (Optional)
1.1 Push crossbar onto shaft at end of arm.
2.1 Use the 4mm allen key to loosely fasten
the handle onto the crossbar.
2.2 Adjust handle to a height that suits the
monitors, then tighten the two screws.
2.3 If not using handle t hole caps.
1.3 Tighten joint
screw to secure
rail to arm.
Too short Too long
OK
Note: Check the crossbar rotation
is smooth after tightening.
1.2 Ensure crossbar is fully pushed
onto shaft.
M6x12
Screw
Plastic
Washer

AWM-LR Page 3 of 4
5. Adjust the ball joint tension
6. Install Cables
5.1 If the monitors are not
holding position or are sti
to move, adjust the tension
plate by tightening or
loosening the three screws.
Note: Adjust 3
screws evenly in
small increments
Note: Support the monitor
while making adjustments.
4. Mount monitors onto crossbar
4.1 Hook the top of the VESA plate onto
the ball joint mount.
4.2 Gently push the bottom of the monitor
until the VESA plate locks into place.
4.3 OPTIONAL security screw
Tilt the monitor upwards to install the
security screw.
Repeat steps 4.1 to 4.3
for second monitor
Tilt Up
Push
Click
Hook
+-
3mm
Allen Key
Important!
Ensure enough cable slack is given to
allow for movement of the monitors.

AWM-LR Page 4 of 4
Push
Loosen
Tighten
8. Adjust level of crossbar
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20190208
8.1 Rotate the crossbar so that it sits
parallel to the worksurface.
+/- 5°
OPTIONAL If the crossbar rotation is too loose or
sti, adjust the tension screw under the centre of
the crossbar.
ANGLEDFLAT
7. Adjust horizontal position of monitors
9. Adjust monitor angle
7.1 Slide the monitors along the crossbar until they are
positioned centrally in the desired position.
7.2 Monitors can also be rotated to portrait position.