Atdec AWMS-2-BT75-FS User manual

AWMS-2-BT75-FS Page 1 of 4
Installation Guide
AWMS-2-BT75-FS
COMPONENT CHECKLIST
M6x6
Button Head Screw (x2)
M6 Washer (x2)
B
Bridge
(x1)
C
Leg
(x2)
A
Post
(x1)
D
Bracket
(x2)
K
M6x6
Button Head Screw
(x4)
L
M6 Washer
(x4)
F
6mm
Hex Key
(x1)
E
VESA Plate
(x2)
G
M8x30mm
Cap Screw
(x4)
J
M8x80
Cap Screw
(x2)
I
M8 Washer
(x2)
L
M4x10 Screw
(x8)
K
Post Cap
(x1)
M
M4x20 Screw
(x8)
N
10mm Spacer
(8x)
H
M8 Nut
(x4)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! EachBracketsupportsamaximumweightasperaboveweightrangespecication.
! ThisproductsupportsVESAmountingholecongurations:75x75mmand100x100mm.
! The manufacturer accepts no responsibility for incorrect installation.
! VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations exert additional leverage that can
exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would
like further information.
! WARNING Death or serious injury may occur if a child climbs on or tips product. Anchor product if applicable. Never place product in
an unstable location. Never place remote control or toys on top of monitors.
Freestanding HD Dual Vert
REQUIRED TOOLS
• Phillips Head Screwdriver
CAPACITY
Flat Monitor
0-25kg(0-55lb)
Curved Monitor
0-18kg(0-39lb)
Display Size
17” - 55”
300mm(12”)maxoverall
display depth

AWMS-2-BT75-FS Page 2 of 4
2. Attach Post to Base
2.1 Insert M8x80 Cap head
screw through M8 washer
and holes in Base and
fasten in Post. Repeat step
with other screw before
tightening both screws.
I
J
A
3. Slide Brackets onto Post and Set Height
3.1 Line up the inner guide
on rear of bracket with
rear channel on post. Slide
inner guide into channel,
then lower bracket.
3.2 Firmly tighten hand
knob at chosen height.
Never loosen knob while
display is on bracket.
1. Assemble Base
1.1 Align Bridge and Leg
holes. Use 6mm hex key.
HoldM8nutinhexagonal
recessuntilM8x30Cap
screw engages. Tighten
screw.
65%
A
B
G
H
1.2 Repeat on
opposite leg.
2.2 Remove clips and
covers from post by
sliding up and out or
by squeezing sides.
NOTE
Rest short end of Bridge on a
soft surface while fastening
C
B
G
H
F
65%
A
B
G
H
NOTE
Assemble with
Cable Covers facing
backwards (Towards
the small side of Base)
D
TIGHTEN
NOTE Never loosen
knob while display
is on �
3.3 Repeat Steps
3.1to3.2with
second Bracket.
Fit Post Cap.
K
≥ HEIGHT
OF
SCREEN
NOTE
Set spacing
between
bottom of
brackets to
be equal to
- or slightly
more than
- display
height
SQUEEZE
to release
I
J
A
D

AWMS-2-BT75-FSPage3of4
5. Mount Bottom Display
75mm
100mm
75mm
100mm
NOTE
For 75mm VESA
unscrew 5mm to
access top holes E
L
TOP
4.2 Attach VESA Plate
withM4x10screws.
ORForrecessedVESAuse10mm
SpacersandM4x20screws.
4.1 VESA mount compatibility
5.1 Set VESA plate to open
position.
Bottom Display must be
mountedonbracketrst.
Use two people for wide or
heavy display.
4. Attach VESA Plates to Displays
E
M
N
OPEN
5.2 Lift display until Vesa Plate
is above the Bracket.
5.3 Centre VESA close to post
and slowly lower until bar on
VESA Plate sits in saddle in
bracket.
WARNING
Do not loosen
hand knob once
display mounted.�
CLOSED
5.4 Set VESA Plate to closed
position by sliding clips on
both sides inwards
5.5 Adjust Display tilt angle by
gripping edges of screen and
rolling up or down to desired
position. .
5.6 Set Display angle by
tightening Tilt Knobs.
OPEN
TILT KNOBS

AWMS-2-BT75-FS Page 4 of 4
7. Fine Adjustment
6. Mount Top Display
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reservestherighttoalterspecicationswithoutnotice.©20220905
6.1 Check that distance
between Brackets is equal
to or greater than the
height of the Display.
Repeat Step 5 to secure
top Display and set tilt
angle.
Lower
Close
Adjust angle
Set angle
i
ii
iii
iv
Unstacked Stacked
Cables can
exit from the
side of the
cable cover
PUSH
PUSH
PUSH
8. Manage Cables
8.1a Load cables into
cable clip.
8.1b Insert one side of the
cable clip into a channel
on the post, then push in
the other side.
Load cables into
cable cover
8.2a Load
cables into
cable cover.
8.2b Clip the cable cover
back onto rear post
channels.
7.1 To correct horizontal angle
ofdisplay+/-3°:
Turnasingleneadjustment
knob to adjust angle of
screen.
Clockwise = Higher
Anti-clockwise = Lower
7.2 To close small gap between
displays+/-6mm(1/4”):
Turnbothneadjustment
knobs - alternating sides a few
rotations at a time.
Clockwise = Higher
Anti-clockwise = Lower
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
FINE HEIGHT ADJUST
FINE ADJUSTMENT
KNOBS
NOTE
Ensure clips are in
CLOSED position after
fine adjustment complete