Atdec AWM-BT User manual

AWM-BT Page 1 of 2
Installation Guide
AWM-BT
COMPONENT CHECKLIST
B
Bracket
(x2)
A
VESA Plate
(x2)
C
M4x10
Screw
(x4)
D
M4x20
Screw
(x4)
E
10mm
Spacer
(4x)
F
4mm
Hex Key
(x1)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! EachBracketsupportsamaximumweightasperabovecapacityspecication.
! Thisproductisnotsuitableforoutdooruse.
! Donotusethisproductformobileapplications.
! VESAmountedaccessories(suchasminiPCbracketsandmounts),andoffsetVESAlocationsexertadditionalleveragethatcan
exceedthecapacityofthemounteventhoughthemonitorweightmaybewithinthestatedrange.PleasecontactAtdecifyou
wouldlikefurtherinformation.
AWMTiltBracket
REQUIRED TOOLS
•PhillipsHeadScrewdriver
CAPACITY
Flat Monitor
4.5-25kg(10-55lb)
Curved Monitor
4.5-18kg(10-39lb)
300mm(12”)maxoverall
displaydepth
Screen Size
24”-55”

AWM-BT Page 2 of 2
2. SlideBracketontoPost,SetHeightandMountDisplay
1.1 VESAmountcompatibility
1. AttachVESAPlatetoDisplay
75mm
100mm
75mm
100mm
NOTE:
For 75mm
VESA unscrew
5mm to access
top holes A
D
E
1.2 AttachVESAPlatewith
M4x10Screws.
A
C
TOP
WARNING:
Do not loosen
hand knob once
display mounted�
2.3 SetVESAPlateto
openposition.
2.4 LiftdisplayuntilVESA
Plateisabovetheheightof
theBracket.
2.5 WithPostcentered,
slowlylowerdisplayuntil
baronVESAPlatesitsin
saddleinBracket.
2.6SetVESAPlate
to closedposition
byslidingclipson
bothsidesinwards.
3. FineAdjustment
Noportionofthisdocumentoranyartworkcontainedhereinshouldbereproducedinanywaywithout
theexpresswrittenconsentofAtdecPtyLtd.Duetocontinuingproductdevelopment,themanufacturer
reservestherighttoalterspecicationswithoutnotice.©20221014
2.2Firmlytighten
handknobatchosen
height.
B
AWM POST
(not supplied)
Arrow side
towards user
TIGHTEN
OPEN
2.7Adjustdisplay
tiltanglebygripping
edgesofscreenand
rollingupordownto
desiredposition.
2.8Tightentiltknobs
tosetdisplayangle.
ORForrecessedVESAuse10mm
SpacersandM4x20Screws.
B
AWM POST
(not supplied)
Arrow side
towards user
OPEN
CLOSED
3.1Tocorrecthorizontalangleof
display+/-3°:
Turnasingleneadjustmentknob
toadjustangleofscreen.
3.2Toclosesmallgapbetweendisplays
+/-6mm(1/4”):
Turnbothneadjustmentknobs-
alternatingsidesafewrotationsatatime.
Clockwise=Higher
Anti-clockwise=Lower
FINE HEIGHT ADJUST
FINE ADJUSTMENT
KNOBS
NOTE:
Ensure slide clips in
CLOSED position after
fine adjustment complete
2.1Lineuptheinnerguide
onrearofBracketwith
rearchannelonPost.
Slideinnerguideinto
channeland
lowerBracket.
Clockwise = More friction
Anti-clockwise = Less friction
OPTIONAL ADJUSTMENT
- TILT FRICTION
4mm Hex Key can be used
to reduce tilt friction (for
light screen) or increase tilt
friction (for heavy screen).
F
TILT
KNOBS
CLOSED