Atid AT911 PLUS User manual

AT911 PLUS USER GUIDE

AT911 PLUS User Guide
2
User Manual Guide
Before You Begin ......................................................................................................................... 3
Chapter1. Caution when using ..................................................................................................... 4
1. How to use the battery correctly.............................................................................................. 4
2. Caution when using.................................................................................................................. 4
Chapter 2. Products compositions .............................................................................................. 5
1. Package components .............................................................................................................. 5
2. Name of each part ................................................................................................................... 6
Chapter3. Basic Functions .......................................................................................................... 8
1. Power and battery ................................................................................................................... 8
1.1 Detaching and Attaching Main Battery ......................................................................... 8
1.2 Charging.......................................................................................................................... 9
1.3 Low power mode (Sleep mode) ..................................................................................... 9
1.4 Batter replacement....................................................................................................... 10
2. System reset (Cold reset)..................................................................................................... 10
3. Use Micro SD, SIM, SAM Card ............................................................................................. 11
3.1 Micro SD Card Installation............................................................................................. 11
3.2 SIM Card Installation ..................................................................................................... 12
4. System settings ...................................................................................................................... 13
4.1 Set Screen Brightness.................................................................................................. 13
4.2 Set sound volume ......................................................................................................... 13
5. Use keypad............................................................................................................................. 14
5.1 Use keypad ................................................................................................................... 14
5.2 Keypad button execution ............................................................................................. 14
Chapter 4. Use Peripheral Device .............................................................................................. 15
1. Barcode scanner .................................................................................................................... 15
1.1 Read 1D or 2D barcode................................................................................................ 15
2. WLAN connection................................................................................................................... 16
2.1 Turn Wi-Fi on / Turn Wi-Fi off ..................................................................................... 16
3. Bluetooth ................................................................................................................................ 17
3.1 Turn on/off Bluetooth.................................................................................................... 17
4. Use Camera............................................................................................................................ 18
4.1 Use Camera................................................................................................................... 18
5. Use UHF ................................................................................................................................. 19
5.1 UHF RFID Program........................................................................................................ 19
Chapter 5. Appendix................................................................................................................... 20
Product Specifications ............................................................................................................... 20

AT911 PLUS User Guide
3
Before You Begin
This user manual is protected by copyright.
This manual is published by ATID Co., Ltd. and can only be copied, edited or distributed by
ATID.
Some contents in the manual may be slightly different from the actual device.
The contents in the manual is subject to change without notice.
This manual is written for the person who is responsible for installing, configuring, and
maintaining the AT911 PLUS. It provides you with information about the features of the AT911
PLUS, and how to install, configure, operate, and maintain it.
Safety information
Your safety is extremely important. Read and follow all warnings and cautions in this document
before you handle and operate ATID equipment. If you do not follow the safety warnings and
cautions, you might be seriously injured, and the equipment and data are also might be
damaged.
◼WARNING
A warning requires you must pay attention to the operating procedure, practice,
condition, and statement strictly, or might be injured seriously.
◆CAUTION
A caution alerts you that you must be observe strictly when you operating procedure,
practicing, configuring, for preventing from damage and destruction of equipment, and
loss of data.
⚫NOTICE
A notice provides you the information which you must needs while you are using AT911
PLUS.

AT911 PLUS User Guide
4
Chapter1. Caution when using
Before you handle and operate your device, please read through and familiar with the contents
of this manual.
1. How to use the battery correctly
⚫When you dropped the main body or battery in water, please do not put it on the stove or
heater for drying. Just keep it in natural temperature or contact with purchase place.
⚫Please do not take the metal object to approach to the terminal of battery.
⚫If you do not use the battery for a long time after charging, please keep it at room
temperature.
⚫According to the life of battery and processing time of its using, the buffering time can be
shortened. In this case, please contact your dealer
⚫You have to charge the device with the provided adaptor from factory.
2. Caution when using
⚫User careless or products repair might damage the stored data. Manufacture is not
responsible for this damage, so important data should be kept separately.
⚫If you have problem, do not try to repair or disassemble the product arbitrarily, please
contact customer service center.
⚫Do not use your where have electromagnetic wave or the risk may occur such as hospital,
plane so on.
⚫A high temperature or high humidity environment will cause trouble, please note that.
⚫Please do not using another sharp object to touch the screen, otherwise it might get
damaged or not working properly.
⚫If smell odors, occurs smoke or noise during use product, immediately disconnect the
charger and off the power, then Please contact with customer service center
⚫If you have any other questions during use, please contact the customer service center

AT911 PLUS User Guide
5
Chapter 2. Products compositions
AT911 PLUS, Android OS based device, can support barcode scanner, RFID tag reader,
wireless communication modem, camera etc. and can be widely used in a variety of work
environments.
1. Package components
After opening the product packaging box, check the
items listed as below:
1) PDA
2) Standard battery pack for the body
3) Adaptor
4) Sync Cable
If there is missing or defective products as below, please contact the customer support center
of your place of purchase
1. 2. 3.
4.
< In the Packing box >

AT911 PLUS User Guide
6
2. Name of each part
<Top Side View>
<Left, Right Side View>
Charge, Wireless Statues LED
Receiver
LCD Touch Screen
KEY PAD (Menu, Home, Scan, Back, Search)
Ear Phone
Jack
Power Key
Side Key
KEY PAD

AT911 PLUS User Guide
7
<Front View>
<Back Side View>
Camera
Barcode Scanner
UHF RFID Antenna
USB Synchronization / DC Power Port

AT911 PLUS User Guide
8
Chapter3. Basic Functions
1. Power and battery
PDA is composed of main battery. The Main battery supplies the power to the system and RAM
which can save and conserve the data.
Main Battery: 3.7V 2,200mA Lithium-ion
Attach the main battery to the back side battery compartment of the PDA.
Push the batter lever inside so that the battery is firmly attached to the PDA.
“Refer to 1.1 Battery attaching and detaching”
Connecting adaptor to the PDA adaptor connecting jack, and check if the “Power LED”is Red,
and then charging the power completely until it turns into Green.
⚫Note:
When the desktop screen shows after starting the system, press the <power> button for a couple of
seconds can reduce the recharging time.
1.1 Detaching and Attaching Main Battery
➢Detaching Battery
These images as below, shows the back bottom of the PDA.
Slide the battery latch to the right (UNLOCK side), and then lift the main battery out of the
compartment along both sides of groove.
7
Battery Locking Lever

AT911 PLUS User Guide
9
➢Attaching Battery
Put the top part of battery into the upward groove, and then press down the bottom of battery
into the battery compartment, slide battery latch to the left (LOCK side) to attach battery firmly.
1.2 Charging
You have to charge the battery via dedicated adapter, which provided from the factory.
“Power LED” is Red while charging or is Green when charged completely. When fully charged,
the LED light will be turned off.
➢Connecting Adapter
1. Plug in the adapter into the 220V socket.
2. Connect the Mini USB jack to the PDA’s
“USB connecting jack”.
3. When “Power LED”shows red light,
it means that the device is being charged.
1.3 Low power mode (Sleep mode)
When the system is started and shows the main desktop screen or other programs are running,
you can enter into the low power mode (sleep mode) by using the power button. If you want
to use the device again, press the power button again and turn on the system
➢Use low power mode (sleep mode) with Power button
Enter low power mode (sleep mode):
1. If the power button is pressed when the device is
on, the screen will be turned off and the device will
enter the low power mode (sleep mode).
Cancel low power mode (sleep mode)
1. If the power button is pressed when the device is
off, the screen will be turned on and the device will
be turned on.
◆Caution:
You must charge the device using dedicated adapter that is provided from the manufacturer,
or your device might get damaged.

AT911 PLUS User Guide
10
➢Use Automatic low power mode (sleep mode)
If the user does not use the device for a while, system is entered into the low power mode (sleep
mode) automatically. You can change the setting time in control panel and power management
as shown below. Using proper time-out setting prevents the system is on a long time without
the user and extends hours of battery use.
[Menu] -> [Settings] -> [Display] -> [Sleep]
1.4 Batter replacement
If the batteries are damaged or out of its life, buy new batteries to use.
◼Warning!
Discard the dead batteries to the designated place
2. System reset (Cold reset)
If the system is not responding or application program does not work, restart the system by
using reset function.
System reset is used to reboot and initialize the hardware completely. The installed programs
copied files, and registry values will be preserved even after the system reset
[Cold Reset Steps]
Push power button until system is reboot.
[Result]
⚫The system will restart.
⚫The operating system will be loaded again when restarting.