Atlas Irene User manual

READ AND SAVE THESE INSTRUCTIONS
Irene
52” CEILING FAN
FAN RATING AC 120V. 60Hz

Tools and Materials Required.........................................................................................
Package Contents .........................................................................................................
Safety Rules...................................................................................................................
Mounting Options...........................................................................................................
Hanging the Fan ............................................................................................................
Attaching the Fan Blades...............................................................................................
Make the Electric Connections.......................................................................................
Finishing the Installation.................................................................................................
Operating the Remote Control.......................................................................................
Operating Your Fan .......................................................................................................
Care of Your Fan...........................................................................................................
Troubleshooting............................................................................................................
TABLE OF CONTENTS
1
1
2
3
4
5
6
6
7
8
9
9

1
2. PACKAGE CONTENTS
Unpack your fan and check the contents. You should
have the following items:
a-1. Blade set (3) (for Irene-3)
a-2. Blade set (5) (for Irene-5)
b. Hanger bracket assembly
c. Ball / down rod assembly
d. Coupling cover
e. Fan motor assembly
f. Transmitter+holder+2 mounting screws
g. 23A/12V battery
h. Package hardware
1) Mounting hardware:
wood screws (2), screws (2),
lock washers (2), washers (2),
star washers (2), wire nuts (3)
2) Blade attachment hardware:
screws (7), washers (7) (for Irene-3)
screws (11), washers (11) (for Irene-5)
Please do not use any electric or battery powered
tools in the assembly and installation of this or any
Matthews Fan Company product.
a-1
a-2
b
c
d
e
f
g
h
Philips screwdriver
Blade screwdriver
11 mm wrench
Step ladder
Wire cutters
1. TOOLS AND MATERIALS
REQUIRED

1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualified licensed electrician.
3. WARNING: To reduce the risk of electrical
shock and fire, do not use this fan with any
solid-state fan speed control device.
4. WARNING: To Reduce The Risk Of Fire,
Electric Shock, Or Personal Injury, Mount To
Outlet Box Marked Acceptable for Fan
Support of 15.9 kg (35 lbs) or less And Use
Mounting Screws Provided With The Outlet
Box. Most outlet boxes commonly used for
the support of lighting fixtures are not
acceptable for fan support and may need to
be replaced, consult a qualified electrician if
in doubt.
5. The fan must be mounted with a minimum of
7 feet clearance from the trailing edge of the
blades to the floor.
6. To operate the reverse function on this fan,
press the reverse button while the fan is
running.
7. Avoid placing objects in the path of the
blades.
8. To avoid personal injury or damage to the fan
and other items, be cautious when working
around or cleaning the fan.
9. Do not use water or detergents when cleaning
the fan or fan blades. A dry dust cloth or lightly
dampened cloth will be suitable for most
cleaning.
10. After marking electrical connections, spliced
conductors should be turned upward and
pushed carefully up into outlet box. The
wires should be spread apart with the
grounded conductor and the equipment
-grounding conductor on one side of the
outlet box.
11. Electrical diagrams are reference only. Light
kit that are not packed with the fan must be
UL Listed and marked suitable for use with
the model fan you are installing. Switches
must be UL General Use Switches. Refer to
the Instructions packaged with the light kits
and switches for proper assembly.
2
3. SAFETY RULES
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE
BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER
INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.

3
4. MOUNTING OPTIONS
If there isn't an existing UL listed mounting box,
then read the following instructions. Disconnect the
power by removing fuses or turning off circuit
breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the fan
15.9 kgs (35lbs) or less. Do not use plastic outlet
boxes.
Figures 1,2 and 3 are examples of different ways to
mount the outlet box.
Note: You may need a longer downrod to maintain
proper blade clearance when installing on a steep,
sloped ceiling. (Fig. 3)
To hang your fan where there is an existing fixture
but no ceiling joist, you may need an installation
hanger bar as shown in Figure 4.
Outlet box
Outlet box
Figure 1
Figure 3
Figure 4
Outlet box
Figure 2
Provide strong
support
Recessed
outlet box
Ceiling
mounting
bracket
Angled ceiling
maximum 25º

4
Before touching a screw driver thoroughly
read these instructions.
Warning/Caution: Before installing fan, turn off
power at service panel and check all visible
screws and bolts for tightness.
1. Remove the decorative canopy bottom cover
from the canopy by turning the cover counter
clockwise. (Fig. 6)
2. Remove the hanger bracket from the canopy
by removing the 1 of 2 screws from the
bottom of the hanger bracket and loosening
the other one a half turn from the screw head.
Next, turn the canopy counter clockwise to
removing the hanger bracket from the
canopy. (Fig. 6)
3. Secure the hanger bracket to the ceiling outlet
box using screws and washers included with
your outlet box. (Fig. 7)
4. Remove hanger ball from down rod assembly
by loosening set screws, removing the cross
pin and sliding ball off rod. (Fig. 8)
Ceiling
hanger
bracket
Mounting screws
(supplied with
electrical box)
Hook
Electrical
box
Figure 7
Figure 8
120V Wires
Washers
Downrod
Cross pin
Hanger
ball
Set screw
6. HANGING THE FAN
Figure 6
Ceiling
hanger
bracket
Ceiling
canopy
Canopy
cover
Figure 5
5. ATTACHING THE FAN
BLADES
1. Fasten blade to motor using the screws supplied.
(Fig. 5)
2. Repeat process with other blades. Tighten each
screw and make sure the blade is straight.
NOTE: This fan includes is supplied with two types
of blades installation. Follow the step below to
installing your fan blade properly.
The inner holes are for 3 blades. (for Irene-3)
The outer holes are for 5 blades. (for Irene-5)
Blade
Screw

5
Figure 10
Registration
slot
Screw
Safety cable
Figure 9
5. Loosen the two set screws from the central
shaft/top coupling of the motor assembly.
Doing so will allow the down rod to enter the
central shaft. (Fig. 9)
6. Carefully feed the fan wires through the down
rod and pull them taut. Thread the down rod
into the central shaft and tighten well.
Re-tighten the set screws against the
downrod.
7. Slide the coupling cover (with wide end
oriented to floor) down the down rod.
Tighten the set screws of the coupling cover
so that it is secure in its new position.
8. Slide canopy ring (with decorative side
oriented to floor) and canopy (with wide end
oriented to ceiling) onto down rod. Carefully
reinstall hanger ball onto rod. Be sure that
cross pin is in correct position, the set screw
on hanger ball is tight and that the wires are
not twisted.
9. Now lift the motor assembly (fan with blades)
into position and place the hanger ball into
the hanger bracket. Rotate down rod until
the "Check Tab" has dropped into the
"Registration Slot" and the down rod and ball
assembly seat firmly. The down rod and ball
assembly should not rotate if this is done
correctly. (Fig. 10)
10. An additional safety support is provided to
prevent the fan from falling. Secure the
safety cable to the ceiling joist with screw
and washer. (Fig. 10)
Supply wires
Downrod
Coupling cover
Canopy
Canopy ring
Set screws
Hitch pin Lock pin

7. MAKE THE ELECTRIC
CONNECTIONS
Remember to disconnect the power. Follow the
steps below to connect the fan to your
household wiring. Use the wire connecting nuts
supplied with your fan. Secure the connectors
with electrical tape. Make sure there are no
loose strands or connections.
1. Connect the fan supply (black) wire to the
black household supply wire as shown in Figure
10.
2. Connect the neutral fan (white) wire to the
white neutral household wire. (Fig. 11)
3. Connect the fan ground wire (green) to the
household ground wire.
4. After all splices are made, check to make
sure there are no loose strands. As an
additional precaution we suggest to secure the
plastic wire connectors to the wires with
electrical tape.
8. FINISHING THE
INSTALLATION
1. Tuck connections neatly into ceiling outlet
box.
2. Slide the canopy up to hanger bracket and
place the key hole on the canopy over the screw
on the hanger bracket, turn canopy until it locks
in place at the narrow section of the key holes.
(Fig. 12)
3. Align the circular hole on canopy with the
remaining hole on the hanger bracket, secure by
tightening the two set screws. Note: Adjust the
canopy screws as necessary until the canopy
and canopy cover are snug.
Warning: Make sure tab at bottom of hanger
bracket is properly seated in groove of hanger
ball before attaching canopy to bracket. Failure
to properly seat tab in groove could cause
damage to electrical wiring.
Figure 11
White (neutral)
Green or bare
copper (ground)
White ("AC IN N")
Ground (green)
(Connect to ground wire
on hanger bracket if no
house ground wire exists.)
Outlet box
Black ("AC IN L")
Black (motor)
Figure 12
Outlet box
Hanger
bracket
Canopy
Canopy cover
Screws
6

7
Figure 13
Figure 14
9. OPERATING THE
REMOTE CONTROL
Your DC brushless motor is equipped with a
automatically learned type remote control. Restore
power to ceiling fan and test the transmitter as below
for proper operation:
Install one 23A/12V battery (included). To prevent
damage to transmitter, remove the battery if not used
for long periods of time (Fig. 13)
Restore power to ceiling fan and test for proper
operation.
A. I, II, III, IV, V and VI button:
These six buttons are used to set the fan speed as
follows:
I = minimum speed
II = low speed
III = medium low speed
IV = medium speed
V = medium high speed
VI = high speed
B. Button:
This button turns the fan off.
C. Reverse button:
This button is to control fan direction.
D. SET code setting button:
Follow the below steps to use the SET button:
a) With the fan’s power off, arrange code switches to
desired code setting.
b) After installing the unit and restoring power to the
fan, press and hold the “SET” button 1 - 5 seconds. You
must press the “SET” button within 60 seconds of
restoring power to the fan.
c) The fan will start to run and begin the control setting
process. The fan will run in both directions for a total of
approximately 5 minutes.
d) When the fan stops after approximately 5 minutes,
the control and speed setting process is complete and
the fan is ready for use.
The receiver provides the following protective function:
1. Lock position: The DC motor has a built-in safety
against obstruction during operation. If there is an
obstruction, the motor will stop and then the power will
automatically go off in 30 seconds. Remove the
obstruction and reset.
2. Over 80W protection: When the receiver detects
motor power consumption which is greater than 80W,
the receiver power will be stopped and operation will
immediately discontinue. Wait for 5 seconds and then
turn the receiver power back on.
ON ECE
1234
ON
D

8
Figure 15
Figure 16
10. OPERATING YOUR
FAN
Speed settings for warm or cool weather depend on
factors such as the room size. Ceiling height,
number of fans and so on.
NOTE: To operate the reverse function on this fan,
press the reverse button while the fan is running.
Warm weather - (Forward) A downward airflow
creates a cooling effect as shown in Fig. 15. This
allows you to set your air conditioner on a warmer
setting without affecting your comfort.
Cool weather - (Reverse) An upward airflow moves
warm air off the ceiling area as shown in Fig. 16.
This allows you to set your heating unit on a cooler
setting without affecting your comfort.

9
12. TROUBLESHOOTING
Problem
Fan will not start.
Fan sounds noisy.
Remote control
malfunction.
Fan wobble.
Solution
1. Check circuit fuses or breakers.
2. Check line wire connections to the fan and switch wire connections in the switch
housing. CAUTION: Make sure main power is off.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.
3. Make sure wire nut connections are not rubbing against each other or the interior wall
of the switch housing. CAUTION: Make sure main power is off.
4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear
during this time.
5. If using an optional light kit, make sure the screws securing the glassware are tight.
Check that the light bulb is also secure.
6. Some fan motors are sensitive to signals from solid-state variable speed controls. If
you have installed this type of control, choose and install another type of control.
7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the
ceiling.
1. Do not connect the fan with a wall mounted variable speed control(s).
2. Make sure the dip switches are set correctly.
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this
level by selecting a point on the ceiling above the tip of one of the blades. Measure this
distance.Rotate the fan until the next blade is positioned for measurement. Repeat for
each blade. The distance deviation should be equal within 1/8".
3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades
can redistribute the weight and possibly result in smoother operation.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE
FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
11. CARE OF YOUR FAN
Here are some suggestions to help you maintain your fan
1. Because of the fan's natural movement, some connections may become loose. Check the support
connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not
necessary to remove fan from ceiling.)
2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or
lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration
or tarnishing. Do not use water when cleaning. This could damage the motor, or the wood, or possibly
cause an electrical shock.
3. You can apply a light coat of furniture polish to the wood blades for additional protection and enhanced
beauty. Cover small scratches with a light application of shoe polish.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.
IMPORTANT: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU
ATTEMPT ANY REPAIRS. REFER TO THE SECTION "MAKING ELECTRICAL CONNECTIONS".