Atlona Opus Series User manual

Installation Guide
1
AT-OPUS-810M
Opus 4K HDR HDMI to HDBaseT 8x10 Matrix Switcher
AT-OPUS-810M
AT-OPUS-810M
1 x AT-OPUS-810M
1 x Captive screw connector, 5-pin
9 x Captive screw connector, 4-pin
12 x Captive screw connector, 3-pin
1 x Pair rack mount ears
4 x Feet w/screws
1 x IEC power cord
1 x IR remote control
1 x Installation Guide
Package Contents
The Atlona AT-OPUS-810M is part of the Opus™ Series of HDMI® to HDBaseT™ matrix switch-
ers for high dynamic range (HDR) formats. The 8x10 matrix switcher is HDCP 2.2 compliant and
support 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling, as well as HDMI data rates up to 18
Gbps. The Opus Series enables exible routing to HDBaseT outputs plus two additional HDMI
outputs, and is compatible with the Atlona AT-OPUS-RX receiver or AT-JUNO-451-HDBT switch-
er for transmission of HDMI, Ethernet pass-through, and bidirectional IR and RS-232 control
signals up to 330 feet (100 meters) over CAT6a/7 cable. Visually lossless VESA Display Stream
Compression (DSC) enables HDR and 4K/60 4:4:4 signal extension over HDBaseT with little to
no latency. Opus matrix switchers are equipped with a comprehensive host of audio and control
system integration features, making them ideal for a wide range of residential and commercial
applications requiring multi-zone AV distribution.
IMPORTANT: Visit https://atlona.com/product/AT-OPUS-810M for the latest rmware
updates and User Manual.

Installation Guide
2
AT-OPUS-810M
1 2 345678 1 2 3 4 567 8 9 10
AUDIO IN
1 2 1 2 3 4 5 6 7 8 9 10
LAN DEBUG IR INRS-232
RX STX RL R
L
AUDIO OUT
RL RL RL RL R
LR
LRL RL R
LR
L
1 2
TOSLINK IN
3 4 1 2 3 4 56 7 8 910
TOSLINK OUT IR IN IR OUT
SS S S S S S S S S S S S S S SS S
ON
1 2 3 45 6 7 8 1 2 3 4 5 6
PoE
LINK
HDBaseT OUT
7
8
HDMI OUT
910
CHASSIS
GROUND
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
AT-OPUS-810M
HDMI IN
AT-OPUS-810M
CANCEL INFOEDIDFNC
1 2 3 4
POWER ENTER 6 7 8 9
5
10
OPUSTM
PWR: 100-240VAC 50/60HzOFF
1 Function Buttons
Power - Sets the unit in and out of
standby.
Enter - Used for making selections.
FNC - Use to switch number buttons to
their secondary function.
CANCEL - Navigates back one step in the
OSD.
2 Number Buttons
Use for selection of inputs and outputs.
1- Press FNC + 1 to route selected input
to all outputs.
2- Press FNC + 2 to turn the front IR
receiver on and o.
3- Press FNC + 6 to open the EDID menu.
4- Press FNC + 7 to display the device
rmware. Press 7 again to view more info.
3 HDMI IN
Connect HDMI cables to these ports from
HDMI sources.
4 HDBaseT OUT
Connect a CAT5e/6/6a/7 cable from this
port to an HDBaseT receiver.
5 HDMI OUT
Connect HDMI cables from these ports to
local HDMI displays.
6 TOSLINK IN
Connect digital audio sources to these
ports.
7 LAN
Connect an Ethernet cable from this port
to a Local Area Network (LAN).
8 DEBUG
Connect a mini USB cable from this port
to a PC to troubleshoot the unit.
9 Control Port
Connect a third party controller or PC
to control the matrix through either IR or
RS-232
10 TOSLINK OUT
These ports provide digital audio output to
audio DSPs, ampliers, or player devices.
11 AUDIO IN
Connect unbalanced 2CH audio sources
to these ports.
12 IR IN
Connect a control system to these ports
to route IR signals to the corresponding
HDBaseT outputs.
13 AUDIO OUT
This port provides source audio 2CH de-
embedding and direct audio loop through
for the audio inputs.
14 IR OUT
These ports provide an output for IR
signals to each source and the two local
HDMI outputs.
15 Power Switch
Toggle this switch to power the unit on
or o.
16 100-240VAC 50/60Hz Power Port
Connect the included IEC cord from this
port to the wall for power.
Panel Descriptions
35
6 7 8 9 11 1310 12 14 15 16
4
12

Installation Guide
3
AT-OPUS-810M
IR
4-pin captive screw connectors have been
included for IR routing. Each 4-pin connect
will provide connection for 2 IR ports. All IR
ports will use a Ground ( ) and signal (S)
wire.
Pin out will be determined by the
RS-232 cable and connect as
RX (receive), TX (transmit) and
(Ground).
A 5-pin captive screw connector for control has been included. The rst three terminals are RS-
232 control, the last two terminals are for IR.
IR IN is connected by a ground and
signal wire. Use with 3rd party control
systems. For easy termination, Atlona
recommends using the 2 meter IR
cable AT-LC-CS-IR-2M.
Control
RS-232 IR
GND S
GND RX TX
GNDRX TX
Mounting Instructions
The AT-OPUS-810M can be mounted in a standard 19-inch rack or placed freestanding on top of
a desk or table.
Rack installation
1. Remove the front two case screws from the sides of the case.
2. Attach the included rack ears to each side of the AT-OPUS-810M using the case screws.
Audio
L R
Connect to an audio DSP, amplier, or other
audio distribution or player devices. Only
unbalanced 2CH connections are compatible
with the 3-pin captive screw audio ports.
+Positive L
Ground
Unbalanced
+Positive R
S S
1 2

Installation Guide
4
AT-OPUS-810M
1 2 345678 1 2 3 4 567 8 9 10
AUDIOIN
1 2 1 2 3 4 5 6 7 8 9 10
LAN DEBUG IRINRS-232
RX STX RL R
L
AUDIOOUT
RL RL R
LRL R
LR
LRL R
LR
LR
L
1 2
TOSLINKIN
3 4 1 2 3 4 56 7 8 9 10
TOSLINKOUT IRIN IROUT
SS S S S S S S S S S S S S S S
SS
ON
1 2 3 4 5 6 7 8 1 2 3 4 5 6
PoE
LINK
HDBaseTOUT
7
8
HDMIOUT
9 10
CHASSIS
GROUND
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
AT-OPUS-810M
HDMIIN
AT-OPUS-810M
CANCEL INFOEDIDFNC
1 2 3 4
POWER ENTER 6 7 8 9
5
10
OPUS
TM
NOTE: Increase the air ow as needed to
maintain the recommended temperature inside
the rack.
NOTE: Do not exceed the maximum weight
loads for the rack. Install heaver equipment in
the lower part of the rack for stability.
3. Install the Opus matrix into a rack, using four rack screws.
1 2 345678 1 2 3 4 567 8 9 10
AUDIOIN
1 2 1 2 3 4 5 6 7 8 9 10
LAN DEBUG IRINRS-232
RX STX RL R
L
AUDIOOUT
RL RL R
LRL R
LR
LRL R
LR
LR
L
1 2
TOSLINKIN
3 4 1 2 3 4 56 7 8 9 10
TOSLINKOUT IRIN IROUT
SS S S S S S S S S S S S S S S
SS
ON
1 2 3 4 5 6 7 8 1 2 3 4 5 6
PoE
LINK
HDBaseTOUT
7
8
HDMIOUT
9 10
CHASSIS
GROUND
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
AT-OPUS-810M
HDMIIN
AT-OPUS-810M
CANCEL INFOEDIDFNC
1 2 3 4
POWER ENTER 6 7 8 9
5
10
OPUS
TM
OPUS
TM
Surface mounting
The AT-OPUS-810M can be placed freestanding on top of a desk, a table, or in a cabinet. To
prevent damage to the surfaces or unnecessary movement of the matrix, four feet have been
included.
1. Turn the unit upside down.
2. Install each foot using the included feet screws, the rubber grips of the feet should be facing
up during installation.
3. Turn the unit right-side up and place it in the desired location.

Installation Guide
5
AT-OPUS-810M
1. Connect up to 8 HDMI sources to the HDMI IN ports.
2. Connect up to 8 HDBaseT receivers (AT-OPUS-RX or AT-JUNO-451-HDBT) to the HDBaseT
OUT ports.
3. Connect up to 2 local HDMI displays to the HDMI OUT ports.
4. Connect up to 4 digital audio sources to the TOSLINK IN ports.
5. Connect up to 2 unbalanced analog audio inputs to the AUDIO IN ports.
6. Connect the TOSLINK OUT ports to an audio distribution device.
7. Connect the 2CH analog AUDIO OUT ports to a DSP, or audio amplier.
8. *Optional* For control, connect to the captive screw port for IR and RS-232.
9. *Optional* For IP control and/or Ethernet routing, connect a network switch to the LAN port.
10. *Optional* For IR routing to and from sources and zones, connect a control system, IR
receivers, or IR emitters to the IR IN and IR OUT ports.
11. Connect the included IEC power cord to the 100-240VAC 50/60Hz power port.
12. Connect the power cord to an AC outlet.
Installation
AT-OPUS-810M
CANCEL INFOEDIDFNC
1 2 3 4
POWER ENTER 6 7 8 9
5
10
OPUS
TM
1 2 345678 1 2 3 4 567 8 9 10
AUDIOIN
1 2 1 2 3 4 5 6 7 8 9 10
LAN DEBUG IRINRS-232
RX STX RL R
L
AUDIOOUT
RL RL R
LRL R
LR
LRL R
LR
LR
L
1 2
TOSLINKIN
3 4 1 2 3 4 56 7 8 9 10
TOSLINKOUT IRIN IROUT
SS S S S S S S S S S S S S S S
SS
ON
1 2 3 4 5 6 7 8 1 2 3 4 5 6
PoE
LINK
HDBaseTOUT
7
8
HDMIOUT
9 10
CHASSIS
GROUND
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
AT-OPUS-810M
HDMIIN
AT-HDR-H2H-44M

Installation Guide
6
AT-OPUS-810M
AMS 2.0
For full conguration of the OPUS, AMS 2.0 is available from https://atlona.com/AMS for free.
Two options can be used for installation: The free Linux based software download or the easy to
install server hardware (AT-AMS-HW).
Once AMS has been set up:
1. Open a browser on the same network as AMS 2.0 and go to the IP of AMS 2.0.
a. View the AMS 2.0 installation instructions on how to nd the IP of the software.
2. Enter the login information on the AMS 2.0 page, then click the Login button.
3. View the OPUS manual for routing and conguration.
WebGUI
The OPUS matrix includes a built-in webGUI, which allows easy management and control of all
features. Follow the instructions below to access the webGUI.
1. View the IP address of the unit using the front panel OSD.
• Press the FNC button.
• Press button 7 (INFO). The rmware version will display on the front panel screen.
• Press button 7 again to bring up the IP address.
2. Launch a web browser and enter the IP address of the unit.
3. The OPUS Login page will be displayed.
4. Enter the following information on the Login page.
Login: admin
Password: Atlona
5. Click the Login button.
NOTE: If the unit is not receiving an IP address from a DHCP server, the unit will default
to 192.168.0.150 255.255.255.0. To set the unit to a set static IP, press the FNC button
followed by 4. Select the Static IP option and press enter. The default static IP address
and netmask is 192.168.1.254 255.255.0.0.

Installation Guide
7
AT-OPUS-810M
Troubleshooting
Problem Solution
I am not receiving
multichannel audio or 3D
video.
• By default, multichannel audio and 3D will not pass
unless all devices support those features. Set each port’s
EDID through the front panel, webGUI, or RS-232.
What rmware am I on? • To view the device rmware version, press the FNC
button, followed by button 7 (INFO). The rmware will
appear on the front panel OSD.
What’s my baud rate? • To view the baud rate of the RS-232 port, press the FNC
button, followed by button 7, then press button 2. The
baud rate will appear on the front panel OSD.
What’s my IP? • To view the IP address of the unit, press the FNC button,
followed by the 7 button twice.
• If the unit is connected to a non-DHCP network, press
FNC, followed by the 4 button. Select the Static IP
option and press Enter. The default static IP address and
netmask is 192.168.1.254 255.255.0.0.
Connection Diagram
4
media4
SET-TOPBOX
OK
224
1 2 345678 1 2 3 4 567 8 9 10
AUDIOIN
1 2 1 2 3 4 5 6 7 8 9 10
LAN DEBUG IRINRS-232
RX STX RL R
L
AUDIOOUT
RL RL R
LRL R
LR
LRL R
LR
LR
L
1 2
TOSLINKIN
3 4 1 2 3 4 56 7 8 9 10
TOSLINKOUT IRIN IROUT
SS S S S S S S S S S S S S S S
SS
ON
1 2 3 4 5 6 7 8 1 2 3 4 5 6
PoE
LINK
HDBaseTOUT
7
8
HDMIOUT
9 10
CHASSIS
GROUND
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
PoE
LINK
AT-OPUS-810M
HDMIIN
AT-OPUS-810M
CANCEL INFOEDIDFNC
1 2 3 4
POWER ENTER 6 7 8 9
5
10
OPUS
TM
SP S
PoE
RX TX
HDMIOUTIR IN IR OUT RS-232AUDIOIN ETHERNET LINK PoE DEBUGHDBaseTIN
AT-OPUS-RX
PWR
LINK
RECEIVER
OPUS
TM
USB
USB
USB
GATEWAY
USB USB-C AUDIOOUT
TM
V
ELOCITY
AV LAN
POWER CH5 CH6 CH7 CH8
I
0
4-Channel
ProfessionalAmplifer
AT-JUNO-451-HDBT
AT-OPUS-810M
AT-VGW-250
AT-OPUS-RX
DISPLAY
Audio Distribution
Game Console Game Console
BluRay Player
Media Player
Control System
Cable Box
DISPLAY
HDBaseT
HDBaseT
Ethernet
Audio
Audio / Video
Audio / Video
Audio / Video
Audio / Video
Audio
Ethernet
Ethernet
POWER INPUT FW
1 2 3 4
INPUT
AT-JUNO-451-HDBT
JUNOXTM
Game Console
GameConsole

Installation Guide
8
AT-OPUS-810M
© 2017 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Version 1
atlona.com •408.962.0515 •877.536.3976