Atlona AT-PRO3HD66M User manual

User Manual
Atlona HDMI to HDBaseT
6 by 6 Matrix Switcher
AT-PRO3HD66M
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515

2
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
1. Introduction .................................................................................3
2. Package Contents .................................................................................3
3. Features .................................................................................3
4. Before You Start .................................................................................3
5. Panel Descriptions
• Front Panel .................................................................................4
• IR .................................................................................4
• Back Panel .................................................................................5
6. Connection and Installation
• 3rd Party Control .................................................................................6
• IR Remote Control .................................................................................7
• Matrix I/O Control .................................................................................8
• I/O Route Memory .................................................................................9
• EDID .................................................................................9-11
• Matrix Status .................................................................................12
7. RS-232
• Connection .................................................................................13
• Set Up .................................................................................13
8. TCP/IP .................................................................................14-21
9. TCP/IP and RS-232 Control
• Control Commands ..................................................................................22
• TCP/IP Commands ..................................................................................22-23
• Baud Rate ..................................................................................23-24
10. Remote Control ..................................................................................24
11. Resetting and Updating ..................................................................................25
12. Specifications ..................................................................................26
13. Safety Information ..................................................................................27
14. Warranty ..................................................................................28-29
15. Atlona Product Registration ..................................................................................29
Firmware 2.0.06 (8/14/13):
DHCP auto on Page 14-21 (TCP/IP instruction has changed)
Table of Contents

3
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
Introduction
With the latest and more affordable HDBaseT®technology extend HDMI®sources up to 230ft over
category cable. The Atlona HDMI 6 by 6 Matrix Switcher allows for effortless control of up to 12
devices through IR, RS-232, TCP/IP and the front panel. With built in S/PDIF ports send audio to an
AVR or distribution amp. To ensure all audio passes through, the 6 by 6 Matrix Switcher supports
all Lossy and Lossless formats of Dolby®and DTS™ over HDMI.
Package Contents
Features
• 1 x AT-PRO3HD66M
• 1 x 24V/6.25A DC adaptor
• 1 x Power cord
• 1 x IR Extender
• 7 x IR Emitter
• 1 x Remote control
• 1 x Pair of dual purpose wall/rack mounts
• 1 x User Manual
• HDBaseT allows IR, RS-232, audio and visual signals to pass over a single category cable.
• Latest feature of Power over Category cable (PoCc™) enables the matrix to power all compatible
receivers.
• IR ports for zone dedicated control through IR remote control and 3rd party control boxes.
• Programmable I/O memories, save I/O routes for faster switching to the most commonly used
configurations.
• EDID™ learning function for up to 6 video display EDIDs.
• Built in internal EDID mode provides 12 individual EDIDs to ensure compatibility when using DVI
projectors or trying to route digital multi-channel audio through an S/PDIF port
• Multiple control options such as RS-232, IR, TCP/IP, and the front panel.
• Dolby®TrueHD and DTS-HD Master Audio™ pass through HDMI output interface.
• Compatible with DVI/D (with DVI/D to HDMI adapter such as AT14050), allowing DVI/D to be
passed to displays.
• Mirrored HDMI outputs on zones 5 and 6 for in room displays or AVRs
• Built in S/PDIF audio de-embedding for AVR or audio distribution amplifiers.
Compatible with PCM 2Channel, Dolby 2.0, Dolby Digital 5.1, and DTS 5.1.
• Optional redundant power supply (AT-PW24V6.25A) in case the main power supply fails.
• HDCP compliant
Before You Start
• Make sure when connecting a category cable a 568B termination method is used.
• Make sure the matrix is connected to a component surge suppressor with line conditioning.
Note: Atlona’s warranty does not cover damage due to electrical disturbances. A component surge
suppressor with line conditioning is highly suggested, especially in areas with electrical
storms.
• Be sure you’re using a mono to mono (2 conductor) 3.5mm IR cable when using IR output
control from 3rd party control boxes, stereo (3 conductor) 3.5mm cables are not compatible.

4
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
DC 24V
BACKUP
MAIN
ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6
MATRIX OUT
RS-232
FW
LAN HDMI IN
HDMI OUTHDMI OUT
MATRIX IN
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
1 2 3 4 5 6
AT-PRO3HD66M
AT-PRO3HD66M
123
456
EDID IR INFO
DEFAULT ALL MEMORY
FCN CANCEL
POWER ENTER
B
M
Panel Description
Front Panel
1. Power Button - Cycles the power between On (blue backlight) or Standby (red backlight) mode.
2. Enter Button - Use to view current status for inputs and outputs or to confirm a command.
3. IR Receiver Window - Receives the signal from the included IR Remote Control or a 3rd party
control box.
4. Function Button - Select for command options. (blue backlight when selected)
a. Default: Mirrors all inputs to corresponding outputs. (i.e. 1 to 1, 2 to 2, 3 to 3, etc.)
b. All: Save a single input to all the outputs with this function
c. Memory: Save/load the current input and output route to memory
d. EDID: Save/Load EDIDs to individual inputs
e. IR: Turn IR receiving on/off (see below)
f. INFO: Displays the firmware version on the front display
5. Cancel Button - Within the functions menu use to go back one screen or to the home screen.
Note: You cannot power off or change functions unless you return to the home screen.
6. Number buttons - Use these buttons to select input and output paths or use with the function
button to change matrix settings.
34
2 a b c
def
1
5
6
The IR receiver window can sometimes pick up stray reflected IR commands causing loss of
functionality. To disable the front panel, see directions below:
IR
---> ---> --->
AT-PRO3HD66M
Select Input Number
home screen
Select Function Option
--------------------
---> Select IR 1:On 2: Off
Current: On/Off
Select IR 1: On 2: Off
Current On
Select IR 1: On 2: Off
Current off
--->
--->
---> --->
--->
--->
Feedback=
”IR On Selected”
Feedback=
”IR Off Selected”

5
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
DC 24V
BACKUP
MAIN
ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6
MATRIX OUT
RS-232
FW
LAN HDMI IN
HDMI OUTHDMI OUT
MATRIX IN
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
1 2 3 4 5 6
AT-PRO3HD66M
AT-PRO3HD66M
123
456
EDID IR INFO
DEFAULT ALL MEMORY
FCN CANCEL
POWER ENTER
B
M
Back Panel
1. Firmware Update - Type B USB Port used for updating matrix firmware
2. RS-232 - Connect to this port for control from a computer or 3rd party control box.
3. Matrix IR In - Used to control matrix I/O switching from a 3rd party IR control box.
4. Matrix IR Out - Global output, combines IR for all incoming zones.
5. Zone dedicated ports
a. IR 3.5mm mono In ports: Used in conjunction with 3rd party IR control box to extend IR
control commands to video displays over category cable.
Note: Be sure you’re using a mono to mono 3.5mm IR cable for 3rd party control boxes,
3.5mm stereo cables are not compatible.
b. IR Out ports: Sends IR signal to sources through a 3.5mm IR emitter
c. Coax Out (S/PDIF): Audio de-embedding for distribution amplifiers and AVRs.
Compatible with PCM 2Channel, Dolby 2.0, Dolby Digital 5.1, and DTS 5.1.
d. CAT5e/6/7 Out (RJ45): Extends video and bidirectional RS-232, IR, and audio signals
through a single category cable.
e. HDMI Out: Mirrored HDMI output
6. Main Power Port - Use included locking DC adaptor to power the matrix switcher
7. LAN Port - For TCP/IP matrix control
8. HDMI Input Ports - Connect HDMI sources into these ports, such as DVD players, Blu-ray players,
computers, etc.
9. Back Up Power Port - Redundant power supply (AT-PW24V6.25A available at atlona.com)
1 2 34
7 8 a b c ed 9
6
5

6
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
Zone IR Control
NO
NC
COM
NO
NC
COM
NO
NC
COM
NO
NC
COM
GND
SIG
+12V
GND
SIG
+12V
GND
SIG
+12V
GND
SIG
+12V
1 2 3 4
RELAYS
WIFI 2
ZIGBEE 12V DC
IR OUT
IDFACTORY
RESTORE
SERIAL 1
SERIAL 2
HDMI COMPONENT
VIDEO OUT
ETHERNET
CONTACTS
AUDIO OUT
AUDIO IN
WIFI 1 eSATA USB
DIGITAL
COAX OUT
1
2
3
4
5
6
L
R
DC 24V
BACKUP
MAIN
ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6
MATRIX OUT
RS-232
FW
LAN HDMI IN
HDMI OUTHDMI OUT
MATRIX IN
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
1 2 3 4 5 6
AT-PRO3HD66M
AT-PRO3HD66M
123
456
EDID IR INFO
DEFAULT ALL MEMORY
FCN CANCEL
POWER ENTER
B
M
RS232 OUT IR OUT
HDMI OUT
CAT5/6
IN
LINK
IR IN
Connection and Installation
3rd Party Controller
Video Display
3rd Party Control box Set Up
IR Emitter
Front Panel
IR Receiver
IR Emitter
AT-PRO3HDREC
Matrix IR Control
With the feature of the IR input zone ports the AT-PRO3HD66M has the ability to receive IR
commands from a 3rd party controller and send it out through the CAT5e/6/7 port to control the
displays in any zone.
Blu-ray Player
FCN CANCEL
POWER ENTER
B
Video
HDBaseT
Audio
Control

7
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
RS232 OUT IR OUT
HDMI OUT
CAT5/6
IN
LINK
IR IN
Note: IR signal is routed through the HDBaseT zone. Only the IR out of the corresponding zone will pass control signal
when using a 3rd party IR controller
IR Remote Control Set Up
DC 24V
BACKUP
MAIN
ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6
MATRIX OUT
RS-232
FW
LAN HDMI IN
HDMI OUTHDMI OUT
MATRIX IN
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
1 2 3 4 5 6
AT-PRO3HD66M
AT-PRO3HD66M
123
456
EDID IR INFO
DEFAULT ALL MEMORY
FCN CANCEL
POWER ENTER
B
M
Video Display
IR
Remote
IR Receiver
Module
Blu-ray Player
IR Emier
AT-PRO3HDREC
Video
HDBaseT
Audio
Control

8
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
I/O Control
The AT-PRO3HD66M’s front panel has 3 functions: I/O control, EDID, and matrix settings. The
following sections go over step by step setup & control.
(I.E. Input 1 to output 2)
(I.E. Input 1 to output 1, input 2 to output 2, etc.)
(I.E. Input 1 to output 1, 2, 3, 4, 5 and 6)
To set an input to an output
To mirror all inputs and outputs
To route one input to all outputs
Feedback =”Input # saved to
Output #”
Feedback =”Mirroring In and Out”
Feedback =
”Input # saved to all”
Matrix Front Panel Functions
--->
--->
--->
--->
--->
--->
--->
---> --->
--->
--->
--->
--->
--->
--->
--->
--->
--->
---> --->
AT-PRO3HD66M
Select Input Number
AT-PRO3HD66M
Select Input Number
AT-PRO3HD66M
Select Input Number
Select Function Option
Select Function Option Select input number
to save to all outputs
Input # to all outputs
Press enter to confirm
Mirror In to Out
Press enter to confirm
Select output number
Press enter to confirm
home screen input selection
input selection
output selection
home screen
home screen
through
through
through

9
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
To save an I/O route to memory
To load a saved I/O route
Feedback =
”Memory # saved”
Feedback =
”Memory # loaded”
--->
--->
--->
--->
--->
--->
--->
--->
--->
--->
--->
--->
--->
--->
--->
---> --->
--->
AT-PRO3HD66M
Select Input Number
AT-PRO3HD66M
Select Input Number
Select Function Option
Select Function Option
1 Save in/out route
2 Select memory route
1 Save in/out route
2 Select memory route
Save to memory (1-6) #
Press enter
Select Memory route 1-6
Press enter to load
home screen
home screen
memory selection
memory selection
Once inputs and outputs have been set they can be saved to memory and recalled later. Up to 6
individual input/output routes can be saved. The route will remain in memory until a new route has
been saved to that memory number or the matrix has been factory reset.
Once an input/output route has been saved, it can be loaded at any time.
I/O Route Memory
O: 1 2 3 4 5 6
I : 4 6 1 3 2 6
example route
When the matrix is completely connected and turned on it will load the default EDID, which is the
highest common native resolution of the devices. (i.e. In the diagram below the default would be
720p with 2ch audio. Multi-channel audio and 3D are not enabled on internal mode, unless
all devices have these features.)
EDID Set Up
Output 2
Output 3
Input 2
1080p-Dolby TrueHD (3D)
Input 1
Output 1
720p-2ch
720p-2ch
1080p (3D)-2ch
1080p-Dolby TrueHD (3D)
DC 24V
BACKUP
MAIN
ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6
MATRIX OUT
RS-232
FW
LAN HDMI IN
HDMI OUTHDMI OUT
MATRIX IN
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
COAX OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
IR IN
IR OUT
CAT5e/6/7
1 2 3 4 5 6
AT-PRO3HD66M
AT-PRO3HD66M
123
456
EDID IR INFO
DEFAULT ALL MEMORY
FCN CANCEL
POWER ENTER
B
M
On default, all devices in the diagram will work at 720p. If a device is not syncing or a different
resolution is required, internal EDID or EDID copy and load should resolve these issues. The
PRO3HD66M can copy up to 6 EDIDs to memory.
through
through

10
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
Step 1: copy an EDID
---> ---> ---> --->
AT-PRO3HD66M
Select Input Number
Select Function Option
home screen
1 To copy up to 6 EDIDs
2 To choose input EDID --->
---> Copy from output #
Save to Memory (1-6) #
Copy from output #
Save to Memory (1-6) #
Feedback=
”Saved port # EDID to
Memory # [Failed/Passed]”
--->
--->
--->
--->
--->
Before an EDID can be loaded to an input, it must first be copied to the matrix’s memory. Each
display’s EDID can be saved individually to one of the matrix’s six preset EDID memories.
memory selection
output selection
Step 2: load a copied EDID onto an input
---> ---> ---> --->
AT-PRO3HD66M
Select Input Number
Select Function Option
home screen
1 To copy up to 6 EDIDs
2 To choose input EDID
Input #
Select an input port
Input # Press Enter
Current: Default
Input: # Mode:
1.Default 2.Saved 3.Int
Input: # Select saved
EDID memory 1-6 (#)
Use EDID memory # + enter
_ _ _
--->
--->
Feedback = ”Save memory # EDID
to input #”
--->
--->
--->
--->--->
--->
---> --->
--->
--->
Atlona EDID - ATL
Pioneer EDID - PIO
Toshiba EDID - TSB
EX.
Once EDIDs have been copied to memory they can be loaded to a specific input.
Note: (refer to the diagram on page 9) Using the EDID of output 3 with input 1 will enable 1080p,
3D, and Dolby TrueHD to pass. Output 2 will receive no audio or video and output 1 will receive no
audio with these settings.
memory selection
input selection
throughthrough
through
through
through

11
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
Step 3: Load an internal EDID on an input
---> ---> ---> --->
AT-PRO3HD66M
Select Input Number
Select Function Option
home screen
Internal EDID options Front panel display readout
1 To copy up to 6 EDIDs
2 To choose input EDID
Input #
Select an input port
Input # Press Enter
Current: Default
Input: # Mode:
1.Default 2.Saved 3.Int
EDID Internal # + enter
ATL _____ ____
--->
--->
Feedback = ”Saved Internal #
To input #”
1- Cycles through
EDIDs in ascending
order
2- Cycles through
EDIDs in descending
order
--->
--->
--->
--->--->
---> --->
--->
--->
If the first two steps don’t produce the correct resolution or audio configuration, the twelve
internal EDIDs should resolve the issue.
*Recommended EDID for use of an AVR
** Recommended EDID for use of the S/PDIF audio de-embedding
*** Recommended EDID for use of DVI projectors
EDID 1: 1080P 2CH audio ATL 1080P 2CH
EDID 2: 1080P HD multi-channel audio 7.1*ATL 1080P Multi CH
EDID 3: 1080P Dolby Digital/DTS 5.1** ATL 1080P DD
EDID 4: 1080P 3D 2CH audio ATL 1080P 3D 2CH
EDID 5: 1080P 3D HD multi-channel audio 7.1*ATL 1080P 3D Multi CH
EDID 6: 1080P 3D Dolby Digital/DTS 5.1** ATL 1080P 3D DD
EDID 7: 720P 2CH audio ATL 720P 2CH
EDID 8: 720P Dolby Digital/DTS 5.1** ATL 720P DD
EDID 9: 1280x800 RGB 2CH audio ATL 1280x800 RGB 2CH
EDID 10: 1366x768 RGB 2CH audio ATL 1366x768 RGB 2CH
EDID 11: 1080P DVI*** ATL 1080P DVI
EDID 12: 1280x800 DVI*** ATL 1280x800 RGB DVI
Internal EDID selection
input selection
RS-232 commands:
To access the different EDIDs through RS-232 the following commands must be used.
Command Feedback Description
EDIDMSetX default EDIDMSetX default Sets the EDID of an input to the default EDID
Ex. EDIDMset2 default - sets input 2 to default
EDIDMSetX saveY EDIDMSetX saveY Sets the EDID of an input to the previously saved EDID memory
Ex. EDIDMset1 save3 - sets input 1 to the EDID memory 3
EDIDMSetX intZ EDIDMSetX intZ Sets the EDID of an input to one of the internal EDIDs
Ex. EDIDMset3 int6 - sets input 3 to the internal EDID - 1080p 3D Dolby
Digital 5.1
through

12
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
Matrix Status
When installing or troubleshooting it’s important to verify settings, or be able to come back to a
project and see how it was set up. The AT-PRO3HD66M matrix settings are viewable through the
front panel display. View current I/O settings, firmware version, FPGA version, IP, and the baud
rates of not just the matrix but extenders as well.
---> ---> --->
--->
--->
AT-PRO3HD66M
Select Input Number
AT-PRO3HD66M
FW Ver: 0.X.XX
AT-PRO3HD66M
Select Input Number
O 1 2 3 4 5 6
I x x x x x x
Select Function Option
home screen
home screen
View Firmware/Baud Rate/FPGA settings
View current I/O settings
AT-PRO3HD66M
Console: X X X X
AT-PRO3HD66M
IP Addr: XXX.XXX.XXX.XXX
AT-PRO3HD66M
Port 1: X X X X
AT-PRO3HD66M
FPGA 1 Ver: 0.0.XX
---> --->
--->
--->
--->
--->
--->
Matrix Baud Rate
IP Address
Output Baud Rate
FPGA Version
--->
--->
--->
--->
-----------------------------------------------------------
115200 8 None 1
OR
9600 8 ODD 0
Press 4 to cycle through
the baud rates of each
output port.
Press 2 to cycle through
IP, Netmask, Gateway,
IP port, and MAC
address
EX.

13
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
RS-232
Connection
RS-232 is connected through a 9-pin female DB connector. Only pins 2, 3, and 5 are terminated.
No. Pin Function
1 ---- Not used
2 Tx Transmit
3 Rx Receive
4 ---- Not used
5 Gnd Ground
6 ---- Not used
7 ---- Not used
8 ---- Not used
9 ---- Not used
1
2
3
4
5
9 8 7 6
Set Up
To set up the RS-232 hyperterminal (if not using 3rd party software) use the following steps:
1. Connect the matrix to a PC using a 9pin to 9pin cable
2. Go to the Device manager folder (see picture A)
3. Find the Matrix COM port and right click with a mouse and select properties (see picture B)
NOTE: If unsure which COM port is the matrix, unplug the 9pin cable and plug it back in. It
will disappear and reappear on the COM port list.
4. Under the properties menu select the port settings tab and update the menu to the matrix
default settings of: Bits Per Second: 115200, Data Bits: 8, Parity: None, Stop Bits: 1 and Flow
Control: None. (see picture C)
Set up is done and any hyperterminal program may be used to control the matrix now.
A
B
C

14
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
A login screen will appear (this is the same log in for admin and general users). For the first log in
(and future admin changes) the username is “root” and password is “Atlona”.
Note: Only the admin password can be changed (see page 18). The username will always remain
“root”.
TCP/IP
For convenience, the matrix comes with DHCP default on. This enables the matrix to be connected
to a network or network device with no worries of the matrix IP overriding another device.
TCP/IP WebGUI
To find the matrix IP:
Atlona has created an easy to use WebGUI for changing settings and controlling the matrix.
To begin, plug a LAN cable into the matrix and your network, then type the IP address of the
matrix into a web browser (as seen below).
Important: If any stability issues are experienced, disable any anti-virus or firewall that may be
interfering with network communication to the Matrix. Once set up is done and the
matrix GUI is no longer being used, the firewall and anti-virus can be re-enabled.
---> ---> --->
AT-PRO3HD66M
Select Input Number
AT-PRO3HD66M
FW Ver: 0.3.XX
Select Function Option
home screen
--->
AT-PRO3HD66M
IP X.X.X.X
--->
IP Address
---> 192.168.000.200
EX.

15
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
The home screen tab will display the general system information. If the matrix is powered off the
FPGA will not display (see first image). Once the power is on it will display (see second image).
Note: When the matrix is turned off many fields within the WebGUI will not display information.
Be sure the matrix is powered on for complete access.

16
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
The network set up page will allow the IP information to be changed. When a change is made the
screen will grey and the ability to save or cancel will display at the bottom (see below).
Note: When DHCP is on, the IP cannot be configured. Turn DHCP off to enable IP configuration.
Note: For a stable connection, when using a control system it is best to set up a static IP.
Note: Be sure to save all changes before moving to the next page
Login Mode has been added to provide a secure telnet login. Once Login Mode has been turned
on a username and password will be required on all IP connections to the matrix.
Note: Login Mode should not be used when using a control system.
Note: The username and password used in IP Login Mode will be the same login information as
the WebGUI

17
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
The config page under status/setting will allow power to be turned off/on, the front IR window to
be turn off/on (see page 4), and the matrix and zone baud rates to be changed (see page 23-24).
A grey screen will display the save and cancel options when making changes. Remember to save all
settings before moving on to the next page.
Note: All like fields can be changed during one edit.

18
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
Adding, deleting, and updating users can also be done from the config page. User changes can
only be done by the admin. Admin user name is always “root” and default password is “Atlona”.
Note: Only the admin password can be changed. The username will always remain “root”
Note: This part of the config page will display for the admin only.
Note: Always remember to save settings before moving to the next page

19
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
The I/O page allows input and output routes to be changed easily by drop down menu. Output All
will route one selected input to all the outputs.
Note: All routes can be changed while in the grey edit screen. Remember to save after all changes
have been made.

20
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
For compatibility and ease of use, EDID configuration has been added. Each input has a drop down
selection for internal, default, and saved EDIDs (see pages 9-11 for EDID information).
Note: When saving an EDID to memory through the WebGUI, the output will save to the
corresponding memory. Ex. Output 2 will only save to Memory 2
Internal EDIDs (see page 11) provide 12 options for video and audio to ensure compatibility and
reliability.
Auto default mode will choose the highest common video resolution and audio format that is
supported by all outputs.
Each EDID saved to memory will be noted as MM and the number of its output.
**Clicking on the Display’s EDID link will provide a breakdown of the selected output’s EDID
Note: MM#s in the picture above are examples of saved EDIDs
Note: Remember to save after all changes to ensure complete compatibility.