ATN ATN OTS LT Series User manual

ATN OTS LT Series
THERMAL HD MONOCULARS
MANUAL
AMERICAN
TECHNOLOGIES
NETWORK
CORP.

2 3
THIS PRODUCT CONTAINS NATURAL RUBBER LATEX, WHICH MAY CAUSE ALLERGIC REACTIONS
CAUTION!
The instructions in this manual are for informational use only and subject to change without notice,
this manual is not to be construed as a commitment by ATN Corp.
ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.
©2020 ATN Corp. All rights reserved.
FEATURES
ATN OBSIDIAN LT CORE
USB TYPE C
STEP ZOOM
ULTRA LOW POWER CONSUMPTION
ERGONOMIC DESIGN
LIGHT WEIGHT
APPLICATION
The ATN OTS LT has been completely redesigned from top to bottom. This
thermal handheld scanner is lighter and has a long lasting internal battery.
Slim and ergonomic, fits perfectly in your hand. Using our new Obsidian LT
Core and Cutting-Edge sensors for sharp crisp images and extended range.
The new battery uses a proprietary power management system that keeps
you in the field longer, without the need to use single use batteries.
This is one tool you’ll want with you at all times. Recovery efforts will seem
effortless, finding game will no longer be frustrating or hard to find. Search and
Rescue operations will be quicker and more efficient!
LEFT/CONTRAST BUTTON
OK / SHORT PRESS NUC /
LONG PRESS MENU BUTTON
ON/OFF BUTTON
DOWN/POLARITY BUTTON
FOCUS ADJUSTMENT
UP/ ZOOM BUTTON
RIGHT/BRIGHTNESS BUTTON

4 5
PREPARING THE DEVICE
UNPACKING
The following steps must be performed before using the device:
1. Open packaging box, remove OTS LT and check the contents.
• Soft Carry Bag
• USB-C cable
• Manual
• Cloth
2. Make sure that nothing is missing.
3. Inspect the device for damage to optical surfaces, body, eyecups, opera-
tion buttons, etc.
4. Ensure that all optical surfaces are clean and ready for use.
NOTE
If any accessories are missing or broken contact ATN’s Customer Ser-
vice at 1.800.910.2862.
CHARGING THE DEVICE
The device is equipped with a USB (type C) port for charging. You will find it
under the rubber cap on the right side of the device.
We have included a USB (type C) charging cable with your monocular. Plug
the cable into a USB wall charger that has an output of 2 amps (Wall Charger
not included).
Charge your monocular for 6 hrs using a 2 A USB wall charger. Note using a
wall charger with lower amperage will take longer to charge your scope.
1. Recommended charger is 2 A USB charger.
2. Battery charging time (from 0 to 100%) is 6 hours with 2 A USB charger.
3. Battery run time is 10 hours on a single charge.
ON/OFF
To Turn On the device press and hold the
Power button until you see the ATN Homes-
creen.
To Turn Off the device press and hold the
Power button.
If the scope freezes or stops responding to
the control panel. Press and hold the Power
button for 1-2 seconds to reboot the scope.
USING YOUR KEYPAD
The keypad is programmed to be used in
two different ways:
• Short and Quick Taps — used for most
functions and to navigate the menu.
• Press and Hold — designed to be used in
the following situations — On/Off, Menu.
SPECIFICATIONS
OTS LT 160 OTS LT 320
Item # TIMNOLT136X TIMNOLT148X TIMNOLT319X TIMNOLT325X TIMNOLT335X TIMNOLT350X Objective lens 19 mm 25 mm 19 mm 25 mm 35 mm 50 mm Resolution 160x120 px / 17 µm 60 Hz 320x240 px / 12 µm 60 Hz
Magnification 3-6x 4-8x 2-4x 3-6x 4-8x 6-12x
Field of view 8.1°x6.2 ° 6.2°x4.7° 11.4°x8.6° 8.8°x6.6° 6.3°x4.7° 4.5°x3° Display Resolution 1280x960 px Eye relief 25 mm Color modes White Hot / Black Hot Internal Lithium Ion Battery 10+ hrs 9+ hrs USB, type C Charging IP rating Weather resistant Human Detection Range 475 m 625 m 535 m 910 m 1510 m 1700 m
Human Recognition Range 240 m 315 m 380 m 455 m 680 m 700 m Human Identification Range 160 m 210 m 230 m 290 m 340 m 400 m Operating Temperature -20°F to +120°F / -28°C to 48°C Dimensions 7.7” x 3” x 2.6”/ 196x76x66 mm Weight 1.2 lb / 560 g Warranty 2 years
* ATN reserves the right to change the above specifications at any time without notice.

6 7
FOCUSING
DIOPTER ADJUSTMENT
By rotating the Diopter Adjustment Ring you will achieve optimal sharpness
for your vision. Look through the eyepiece while focusing on the widgets on
the screen.
NOTE
Once the Diopter Adjustment is set to
your liking, adjustment will not need to be
performed unless another user altered the
focus for their needs.
DISTANCE FOCUS
Rotate the Adjustment Ring, as necessary,
to achieve the proper focus at various dis-
tances.
INTERFACE
MAIN OPERATIONS
OPERATION WITH KEYPAD
1. On/Off button; A long press of this button (1–2 se-
conds) will either power on the unit or power off the
unit, depending on the current status of the monocular.
2. Up button; A short press of this button will cycle
you through your change in zoom (3–6x or 4–8x).
3. Left button; A short press will allow you to perform
a contrast image cycle change (1 →2 →3 →1).
4. OK button; A short press of this button will
perform a manual NUC. A long press (1-2 seconds)
will open the Menu.
5. Right button; A short press allows you to adjust the brightness of your micro
display screen (100% →60% →30% → 10%).
6. Down button; A short press will change your thermal mode from White Hot
to Black Hot.
NOTE
When you press the keypad buttons that change device settings (e.g.
Contrast, Brightness)
you will see in the lower
right corner relevant
information icons and
level number appear for
2-3 seconds.
HOMESCREEN
The first screen you’ll
see after turning on the
device is the Homescreen.
It contains Status Bar
icons and different Infor-
mation Widgets.
DIOPTER
ADJUSTMENT
RING
FOCUS
ADJUSTMENT
RING
MENU
To open the Menu, perform a long
press of the OK button (1 to 2 sec) until
you see the Menu appear on the left
side of the screen. You will see the fol-
lowing Icons:
NUC. This feature allows you to turn
On/Off the auto NUC feature.
PIX. This feature is intended to cor-
rect neutral pixels in the display. Se-
lect the option by using the OK button
when PIX is highlighted.
Move the dot to the area of the display with the neutral pixel, and place the
flashing dot directly over the neutral pixel. A short press of the OK button will
select that pixel for repair. After the short press of the OK button to select the
pixel for repair, a long press of the OK button will exit the pixel correction mode.
SENS. This option gives you the ability to adjust the thermal sensitivity of
your monocular.
HOW TO PERFORM A NUC
NUC’ing helps to improve the image quality when the image is degraded by
various environmental factors. There are multiple NUC tables that span the
full operating temperature range, and the monocular automatically selects the
optimum table based on its temperature.
You can set the system to perform a NUC automatically at a predefined time
interval. Or, you can turn the automatic NUC off and NUC the system manu-
ally, when required. Also, you can use the NUC shortcut from the Homescreen
by quickly pressing the OK button anytime.
Example: Change of temperature, continuous viewing of a particular warm
object, and movement from one environment to another all may cause image
degradation.
In order to turn the automatic NUC On or Off. Press and hold the OK button
for the menu to display. Using your Down Arrow button, scroll to NUC. Press
the OK button to enter the NUC menu. Press the Up button to cycle the NUC
On or Off. Press and hold the OK button to exit the Menu. You can also manu-
ally NUC the scope from the Homescreen by quickly pressing the OK button.
1 2
6
3 4 5
BATTERY
STATUS

8 9
THERMAL
CONTRAST — the difference in luminance and color that makes an object
more distinguishable. You can change the contrast by quickly pressing the
Left Arrow button to cycle through the preset contrast settings.
THERMAL SENSITIVITY — Allows you to select how sensitive the Thermal
Sensor is in picking up thermal heat signatures.
In order to change the Thermal Sensitivity, press and hold the OK button.
When the Menu appears, use the Down Arrow to select SENS. Press the
OK button to enter the Thermal Sensitivity Menu. Press the Up button to cycle
through the sensitivity options. Once you select the Thermal Sensitivity you
would like to use, short press the OK button to save your selection. Press and
hold the OK button to exit the Menu.
WARNINGS AND CAUTIONS
• Always remember to turn off the device when it is not in use.
• Do not disassemble, drop, open, crush, bend, deform, puncture, shred,
microwave, incinerate, paint or insert foreign objects: it will void your war-
ranty.
• Keep the scope in the provided protective cover when not in use.
• Avoid contact with dust, steam, and gas.
• This product contains natural rubber latex which may cause allergic reac-
tions.
• The scope is a precision electro-optical instrument and must be handled
carefully.
• Do not scratch the external lens surfaces or touch them with your fingers.
CAUTION
Failure to follow these safety instructions could result in damage to the
device!
2 YEAR PRODUCT WARRANTY
This product is guaranteed to be free from manufacturing defects in mate-
rial and workmanship under normal use for a period of 3 (three) years from
the date of purchase. In the event a defect that is covered by the foregoing
warranty occurs during the applicable period stated above, ATN, at its option,
will either repair or replace the product, and such action on the part of ATN
shall be the full extent of ATN’s liability, and the Customer’s sole and exclu-
sive remedy. This warranty does not cover a product (a) used in other than
its normal and customary manner; (b) subjected to misuse; (c) subjected to
alterations, modifications or repairs by the Customer or by any party other
than ATN without prior written consent of ATN; (d) special order or “close-out”
merchandise or merchandise sold “as-is” by either ATN or the ATN dealer; or
(e) merchandise that has been discontinued by the manufacturer and either
parts or replacement units are not available due to reasons beyond the control
of ATN. ATN shall not be responsible for any defects or damage that in ATN’s
opinion is a result from the mishandling, abuse, misuse, improper storage or
improper operation, including use in conjunction with equipment which is elec-
trically or mechanically incompatible with or of inferior quality to the product,
as well as failure to maintain the environmental conditions specified by the
manufacturer. This warranty is extended only to the original purchaser. Any
breach of this warranty shall be waived unless the customer notifies ATN at the
address noted below within the applicable warranty period.
The customer understands and agrees that except for the foregoing war-
ranty, no other warranties written or oral, statutory, expressed or implied,
including any implied warranty of merchantability or fitness for a particular
purpose, shall apply to the product. All such implied warranties are hereby and
expressly disclaimed.
LIMITATION OF LIABILITY
ATN will not be liable for any claims, actions, suits, proceedings, costs,
expenses, damages or liabilities arising out of the use of this product. Opera-
tion and use of the product are the sole responsibility of the Customer. ATN’s
sole undertaking is limited to providing the products and services outlined
herein in accordance with the terms and conditions of this Agreement. The
provision of products sold and services performed by ATN to the Customer
shall not be interpreted, construed, or regarded, either expressly or implied, as
being for the benefit of or creating any obligation toward any third party of legal
entity outside ATN and the Customer; ATN’s obligations under this Agreement
extend solely to the Customer. ATN’s liability hereunder for damages, regard-
less of the form or action, shall not exceed the fees or other charges paid to
ATN by the customer or customer’s dealer. ATN shall not, in any event, be
liable for special, indirect, incidental, or consequential damages, including, but
not limited to, lost income, lost revenue, or lost profit, whether such damages
were foreseeable or not at the time of purchase, and whether or not such dam-
ages arise out of a breach of warranty, a breach of agreement, negligence,
strict liability or any other theory of liability.
PRODUCT WARRANTY REGISTRATION
In order to validate the warranty on your product, ATN Europe LTD must
receive a completed Product Warranty Registration Card for each unit or com-
plete warranty registration on our website at www.atneu.com. Please com-
plete the included form and immediately mail it to our Service Center: ATN
Europe LTD, Bulevard Tsarigradsko shosse 7-11 km. Parking lot of METRO 1
store, Sofia Bulgaria 1784.
OBTAINING WARRANTY SERVICE
To obtain warranty service on your unit, End-user must notify ATN Europe
LTD service department by calling [phone] or via e-mail support@
atneu.com to receive a Return Merchandise Authorization number (RMA).
Merchandise Authorization number (RMA).
When returning please take or send the product, postage paid, with a copy
of your sales receipt to our service center, ATN Europe LTD at the address
noted above. All merchandise must be fully insured with the correct postage;
ATN Europe LTD will not be responsible for improper postage or, missing or
damaged merchandise during shipment.

10 11
When sending product back, please clearly mark the RMA# on the outside
of the shipping box. Please include a letter that indicates your RMA#, Name,
Return Address, reason for service return, Contact information such as valid
telephone numbers and/or e-mail address and proof of purchases that will
help us to establish the valid start date of the warranty. Product merchandise
returns that do not have an RMA listed may be refused or a significant delay in
processing may occur.
Estimated Warranty service time is 10-20 business days. End-user/cus-
tomer is responsible for postage to ATN Europe LTD for warranty service.
ATN Europe LTD will cover return postage/shipping to European Union coun-
tries end-users/customers after warranty repair only if product is covered by
aforementioned warranty. ATN Europe LTD will return product after warranty
service by domestic TNT ground and/or domestic mail. Any other requested,
required or international shipping method the postage/shipping fee will be the
responsibility of the end-user/customer.

©2020 ATN Corporation
For customer service and technical support, please contact
American Technologies Network Corp.
1341 San Mateo Avenue, South San Francisco, CA 94080
phone: [phone]
e-mail: [e-mail]
www.atncorp.com