ATN IR940 User manual

ATN IR940
LONG RANGE INFRA-RED ILLUMINATOR
USER GUIDE
Important Export Restrictions! Commodities, products, tech-
nologies and services contained in this manual are subject to
one or more of the export control laws and regulations of the US
BIS-Department of Commerce, Export Administration Regula-
tions. It is unlawful and strictly prohibited to export, or attempt to
export or otherwise transfer or sell any hardware or technical data
or furnish any service to any foreign person, whether abroad or in
the United States, for which a license or written approval of the U.S.
Government is required, without first obtaining the required license
or written approval from the Department of the U.S. Government
having jurisdiction. Diversion contrary to U.S. law is prohibited.
USER’S GUIDE (IR940) REVISION 1 – FEBRUARY 2023
ALIGNING THE IR BEAM
In order to Align the IR940 illuminator to your scope. After the IR940 is
assembled into the mount. Place it on the X-Sight 5 side accessory rail or on
your rifles accessory Picatinny rail. Once mounted securely, slightly loosen
the two screws on top of the mounting ring.
While looking through the X-Sight 5 at night with night mode activated.
Move the IR940 around in the mount until you see the IR light covering your
entire field of view in the X-Sight 5 view finder. Once you have adjusted your
IR light to be aligned with your X-Sight 5 FOV, gently tighten the two screws
on top of the mounting ring with an Allen wrench.
MAINTENANCE
To prevent wear and retain water-resistance it is a good idea to lubricate
the threads and o-rings if they become dry.
TROUBLESHOOTING
Light Doesn’t Turn On
• Check that the battery tube is fully threaded, as well as the tail cap.
Light Dimming
• If the output is declining rapidly unexpectedly, please try another fully
charged battery and/or charge your battery and retry.
• If output is not fixed with other charged batteries, please contact ATN for
further assistance.
For customer service and technical support, please contact
American Technologies Network Corp.
2400 NW 95 Ave, Doral, FL 33172
phone: [phone]
e-mail: [e-mail]
www.atncorp.com
©2023 ATN Corporation

INTRODUCTION
The IR940 IR Illuminator ensures that you stay hidden from your prey. An-
imals and humans alike are not able to see the wavelength at which the
illuminator is emitting.
MOUNT
BATTERY TUBE TAIL CAP
HEAD
MOUNT NUT
MODE ADJUSTMENT RING
ON/OFF BUTTON
SPECIFICATIONS
Wavelength 940 nm
Beam Angle 5°- 80°
Operating Tempe-
rature Range -20°C to +40°C
Battery type
18650R rechargeable; 3.7 V Lithium Ion
Output Three levels : Low at 50% , Medium at 75%, High at 100%
Runtime 6h at 50%, 4h at 75% , 3h at 100%
Lens Material Polycarbonate
Housing Material Alluminium alloy with hard anodized finish
Environmental
resistance Weather resistance
Dimensions
1.9’’ x 1.9’’ x 5.8’’/46 x 46 x 148 mm
Weight 0.38lb / 175 g
Color Black
* ATN reserves the right to change the above specifications at any time without notice.
FEATURES
• HIGH POWER LED EMITTER.
• THREE MODES OF OPERATION.
• SINGLE LITHIUM 18650 BATTERY WITH CHARGER.
• REMOVABLE GRIP RING.
• EASY RAIL MOUNTING SYSTEM.
• BATTERY CHARGER.
• ONE-YEAR WARRANTY.
BAT TERY
NOTE
Please hold the battery tube (not the brightness control ring or neck)
when tightening/loosing the tail-cap.
CAUTION
Only use an 18650 battery to operate this light, do not use 2 CR123
batteries as they may damage the device.
The IR940 IR Illuminator uses one 18650 battery.
1. Remove the tail cap unscrewing it until it is free of the body.
2. Install the battery in the body, observing proper battery polarity.
3. Install the tail cap back on the body.
BATTERY TUBE
TAIL CAP
BATTERY (18650)
M O D E S
The IR940 has three stage output — Low, Medium and High system. Low
at 50%. Medium at 75%. High at 100%.
BRIGHTNESS SETTINGS
The factory preset modes control the brightness of the IR illuminator.
Three modes are designated on the head after the focusing ring. The
modes are distinguishable by the size of the dot. The small dot indicates the
lowest power output setting. The medium dot indicates the medium output
power setting. The large dot indicates the strongest output power setting.
To turn on/off the IR illuminator push the button on the tail cap.
To switch the modes rotate the setting ring behind the focus ring of the IR
illuminator.
FOCUS
Turn the light on maximum output and shine it on a wall 8~10 m away. To
focus the beam, hold the head in one hand and turn the neck section with
your other hand turn clockwise or counter-clockwise.
MOUNT
Attach the IR940 to adjustable mount as follows:
1. Unscrew the two screws.
2. Place the insert in the mount.
3. Insert the illuminator into the mount with insert.
4. Secure the two screws using an Allen wrench. Do not apply excessive
torque.
ILLUMINATOR
INSERT
MOUNT
MOUNT
NUT
SCREWS