atomi smart WiFi Ceramic Tower Heater User manual

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Anyother
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

1 2
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions and register an account.
v4.11/21
Atomi Sma
GET
Register
4
Add your Atomi Sma device
Press “Add Device” or the “+” sign and
select “Connect Device” on the popup that appears
Add Device
5
WiFi
Password
Continue
Select the right network
Enter your home WiFi name and
password, then press “Continue”
Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
If the popup does not appear, close the app and try again.
Still nothing? Read the “Troubleshooting” section on this user guide.
If not flashing, press and hold the WiFi buon for 10s to reset.
Make sure to allow access to Location (Android),
Bluetooth and Local Network (iOS).
Let’s get staed!
Sma WiFi
Ceramic Tower Heater
QuickSta Guide
TO AVOID THE RISK OF AN ELECTRICAL SHOCK, always make sure that the
Sma Heater is unplugged from the electrical outlet before relocating,
servicing, or cleaning it.
CAUTION: To prevent an electric shock, match wide blade of plug to wide
outlet slot and fully inse.
When using electrical appliances, basic safety precautions should always be
followed to reduce the riskof fire, electric shock, and/or injury to people,
including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. The Sma Heater is hot when in use.To avoid burns, do not let bare skin
touch the hot suaces. Use the backhandle of the heaterwhen moving.
Keep combustible materials such as furniture, pillows, bedding, papers,
clothes, and cuains at least three feet (0.9 m) awayfrom the front of the
heater and keep them awayfrom the sides and rear.
3. Extreme caution is necessarywhen the heater is being used by or near
children and whenever the heater is le operating and unaended.
4. Do not operate if the cord or plug has been damaged, if the heater
malfunctions, or if it has been dropped or damaged in any manner.
5. Do not use outdoors.
6. The Sma Heater is not intended for use in bathrooms, laundry areas, nor
similar indoor locations. Never place the heaterwhere it may fall into a
bathtub or water container.
7. Do not run the cord under carpeting. Do not cover the cord under throw
rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord awayfrom high-trac areas where it could
be tripped over.
8. To disconnect the Sma Heater, turn controls to “O”, then remove the
plug from the outlet.
9. Connect to standard outlets only.
10. Do not inse or allow foreign objects to enter any ventilation or exhaust as
this may result in an electric shockor fire. It may also damage the Sma
Heater.
11. To prevent possible fire, do not block air intakes or exhaust in any manner.
Do not use on so suaces like a bed where openings may be blocked.
POLARIZED PLUG
This Sma Heater has a polarized plug (one blade is
wider than the other).
As a safetyfeature to reduce the riskof electrical
shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fully inse into the
outlet, try reversing plug.
IMPORTANT SAFEGUARDS 12. The Sma Heater has hot and arcing or sparking pas inside. Do not use
it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this Sma Heater only as described in this user manual. Any other
use not recommended by the manufacturer maycause fire, electric
shock, or injuryto people.
14. Always plug the Sma Heater directly into a wall outlet/receptacle. Never
use it with an extension cord or relocatable power tap (outlet/power strip).
NOTE: This appliance is for HOUSEHOLD USE ONLY.
ELECTRIC POWER
If the electric circuit is overloaded by other appliances, your Sma Heater
and/or appliances may not operate properly. The Sma Heater should be
operated on a separate electrical circuit from other operating appliances.
Before you begin
1. Remove tie from the power cord and unravel the cord. Keep the plastic
wrapping away from children.
2. Place the Sma WiFi Ceramic Tower Heater on the floor in the desired
location.
3. Know yourWi-Fi networkand password.
4. Make sure that you are operating on:
• iPhone®8 or higher and iOS®8 or higher.
Any previous iPhone®or iOS®may experience slower connections.
• Android™ 4.1x or higher.
5. Make sure that you’re connected to a 2.4GHz Wi-Fi network(Atomi Sma
app can’t connect to 5GHz networks).
List of main pas
Control Buons
Control
Buons
Heat
Output
Intake
Vent
Power
Switch
Solid
Base
Timer
Swing
ECO
High
Low
°F
WiFi
Swing/Oscillation
Heater will rotate
70 degrees backand
foh when pressed.
Timer
Set timer to run from
1-12 hours. When using
this seing, heater will
power o aer the
selected hours.
Mode
Press to change
from LOW and HIGH.
Wi-Fi Buon
LED Display
ON/OFF
Aer power o,
the fan will
continue to work for
30s and then stop.
Temperature Control
Set desired room temperature.
Temperature will blink while adjusting.The heater
may take up to five seconds to respond.
3
Plug in your Atomi Sma device
Use the switch on the back to turn it on and
confirm that the indicator light is flashing.
WiFi

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.

Troubleshooting
Sma WiFi
Ceramic Tower Heater
The following terms and conditions apply to the promo code;
1. Coupon is only valid on the Atomi Sma website www.atomisma.com.
2. Avalid code must be entered at the checkout page in order to redeem the
promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any order, or revoke the
use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in conjunction with
other promotions or discounts.
7. Additional terms and conditions may be specfied in relation to specific
promo code (for example, duration, eligibility, discount amount and
products covered), and will govern the use and redemption of those
vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer replacement
codes, discounts, credits, cash or otherwise compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical issues.
Still can’t connect?
Need assistance?
Our friendly customer service team will
work hard to put a smile backon your face.
Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (US)
or suppo@atomiusa.com
For more information about app and
device features, tutorials and
troubleshooting tips go to:
www.atomisma.com/helpHeater
Welcome to the Atomi Sma family!
We know you will love our products so much
that we are giving you an exclusive 15% o
your next purchase on atomisma.com.
Log onto
hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous US only*
Terms and conditions apply;
This product can expose you to chemicals including Lead, which is known to the State of
California to cause bih defects or other reproductive harm. For more information,go to
www.P65Warnings.ca.gov.
Warning
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is
subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including
inteerence that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to pa 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful inteerence to radio
communications. However, there is no guarantee that inteerence
will not occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the inteerence by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Three-year limited warranty from the date of purchase
against defects in material and workmanship.
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
atomi sma®is a registered trademark of Atomi Inc.
Designed by Atomi in New York. Made in China.
Note:
Changes or modifications not expressly approved by the pay
responsible for compliance could void the user's authority to
operate this device.
Turning O the Sma Heater
Use the ON/OFF buon or the power switch on the Atomi Sma
app to turn o your heater.
NOTE: The LED displaywill stay illuminated and count down from
6 seconds before turning o.
Cleaning and Maintaining Your Sma Heater
CAUTION: Always be sure the Sma Heater is switched OFF,
unplugged and completely cooled before cleaning or aempting
to store the item. DO NOT immerse Sma Heater in water or allow
water to drip into the interior of the Sma Heater, as this could
create an electric shock hazard. DO NOT use anydetergents or
abrasives.
Care and Cleaning
1. Always turn o the Sma Heater and disconnect the cord from
the electrical outlet before cleaning your heater.
2. Accumulated dust may be removed from the Sma Heater
with a so cloth or vacuum cleaner.
3. Ensure the air intake vent on the backof Sma Heater is free
and clear of dust or lint.
4. The removable paicle filter should be cleaned and dried out
at least 1-2 times per season. Remove the air intake vent cover
and hand wash the paicle filter with soap and water.
5. Clean the outside of the heater by wiping it with a damp cloth
and bu with a drycloth.
Storing
Allow the Sma Heater to cool completely before storing. Store in a
dry location. Do not place heavy items on top of the Sma Heater
as this may result in possible damage.
The popup does not appear when adding a
device.
Make sure that you are allowing the app to access your
phone's Location (Android), Bluetooth and Local Network
(iOS). For more details, visit our website’s Suppo page.
If the popup still doesn’t appear, follow the steps below:
1. Press "Add Device" or the “+” sign and select your sma
device.
2. Follow the on-screen instructions (Make sure you
connect to a 2.4GHz WiFi Network).
I can’t find the atomi-sma-XXXX network in
my WiFi list.
Make sure yourAtomi Sma device is plugged in and the
WiFi light is blinking quickly. If not, unplug your Atomi Sma
device and plug it back in to reboot.
- For more ConnectionTroubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine" in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset your
devices and add them again to the app.
How to reset my device.
Press and hold the WiFi buon on the heater panel for10s.
Confirm that the indicator light stas flashing.
Why is the heater still blowing air aer
turning it o?
The heater maycontinue blowing air for a few seconds in
order to cool down the internal components.
My WiFi network doesn’t appear in the Atomi
Sma app.
Use your smaphone to confirm that you have at least two
WiFi bars in the vicinity of your Atomi Sma device. If not,
move your Atomi Sma device closer to your router. (The
list will refresh every10 seconds).
Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi signal is
too weak, reset your WiFi router and try again.
I’m geing “Failed to Add Device”, “Failed to
find router” or “DHCP” error.
- Confirm that your phone is connected to a 2.4GHz WiFi
network.
- Checkwhether the router password you entered is correct.
- Confirm that the DHCP service is enabled on your router
seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does not allow
you to disable 5GHz, try to move faher awayfrom your
router until your phone moves to the 2.4GHz band.