Atronix 9885110 User manual

09/2021 Page 1
RELAY CARD
User Manual
1 to 3kVA
Model Article number
a-TroniX Relay card 1-3 kVA 9885110

Page 2 09/2021
User Manual
a-TroniX Relay card 1–3 kVA
INTRODUCTION
The publication and copyright of this documentation remain with the company:
AKKU SYS Akkumulator- und Batterietechnik Nord GmbH
Verbindungsweg 23 · 25469 Halstenbek · GERMANY
Telefon +49 4101 | 3 76 76-0 / Fax +49 4101 | 3 76 76-66
[email protected] / www.akkusys.de
Thank you very much,
for purchasing our a-TroniX series relay card.
The relay card is an intelligent optional expansion card for your UPS
(Uninterruptible Power Supply).
It´s an electronic module that is used for the potential-free exchange of signals between a
UPS and a higher-level control.
It serves as an interface for the UPS periphery monitoring.
Read carefully before use!
Read this manual carefully before installation.
It contains important regulations and instructions for the use of this product and provides
technical support for the operator of the unit.
All rights reserved.
AKKU SYS Akkumulator- und Batterietechnik Nord GmbH cannot be held responsible for
any inaccuracies or inappropriate information in this instruction manual. The information in
this document is subject to change without notice, but there is no obligation to update it
on an ongoing basis.
We reserve the right to make design and equipment changes to improve the production
process or the product.

09/2021 Page 3
User Manual
a-TroniX Relay card 1–3 kVA
1. Function
The relay card belongs to the intelligent optional expansion cards and is used for direct
and potential-free coupling with external controls and/or machines.
This allows the UPS status to be transmitted in real time to higher-level controls.
2. Definition
Pins denition of connecting terminal on the board:
Terminal No. Terminal function
1 Common source
2 UPS on NO
3 AC fail NO
4 AC fail NC
5 Batt low NO
6 Batt low NC
7 UPS alarm NO
8 UPS alarm NC
9 Bypass active NO
10 Bypass active NC
11 UPS fail NO
12 UPS fail NC
CN4-1 Remote shutdown
CN4-2 GND
For function denition of connecting terminal you can also get relevant information from the
imprint on the rear of the card.
3. Product
appearance
a-TroniX Relay Card for
real-time monitoring of the UPS.

Page 4 09/2021
User Manual
a-TroniX Relay card 1–3 kVA
4. Installation
It applies to high frequency on-line UPS with SNMP SLOT (INTELLIGENT SLOT).
All inputs/outputs are isolated or potential-free.
The relay card can easily be plugged into the adapter slot (INTELLIGENT SLOT) of the
UPS and must then be coupled to the higher-level control via a signal cable.
The card is also congurable, so that essentially the assignment and the switching
behaviour can be dened.
1. Open the cover plate of INTELLIGENT SLOT on the rear panel of UPS.
2. Insert the card directly along the gap of the
INTELLIGENT SLOT until the metal plate of the
connection interface is tight against the surface
of the UPS back panel. This indicates that the
card is inserted correctly. Then use the screw
lock and x the relay card in place.
3. Connect the UPS to the monitor via the connection cable. The monitoring device
displays and controls the operating status of the UPS to allow remote monitoring of the
UPS operation.
5. Recycling & ENVIRONMENT
■ Do not discard waste electrical or electronic equipment (WEEE) in the trash.
Refer to your local codes for disposal requirements.
■ For more information, contact us on the hotline [phone],
at [email protected] or use the QR code.
■ Indicates recycling information.
The packaging is recyclable.
Refer to your local codes for disposal requirements.

AKKU SYS Akkumulator- und Batterietechnik Nord GmbH
Verbindungsweg 23 · 25469 Halstenbek · GERMANY
Tel. +49 4101 | 3 76 76-0 / Fax +49 4101 | 3 76 76-66 / [email protected] / www.akkusys.de
Other manufacturers and product ranges
you will find in our
AKKU SYS complete catalogue:
Page 5 09/2021
Go to our catalogue: