Attero Tech Dante unDX2IO+ User manual

Attero Tech, LLC
1315 Directors Row, Suite 107, Ft Wayne, IN 46808
Phone [phone] • Fax [phone]
www.atterotech.com
614-00036
unDX2IO+
4 x 2 Wallplate
User Manual
Date 5/11/2018
Revision 01_d

unDX2IO+
User Manual
Attero Tech, LLC
1315 Directors Row, Suite 107, Ft Wayne, IN 46808
Phone [phone] • Fax [phone]
www.atterotech.com
614-00036
IMPORTANT SAFETY INSTRUCTIONS
The symbols below are internationally accepted symbols that warn of potential hazards with electrical products.
This symbol, wherever it appears, alerts you to the presence of un-insulated dangerous voltage inside the
enclosure -- voltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the
accompanying literature. Please read the manual.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and third grounding prong. The wider blade or
the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by Attero Tech
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
13. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
14. Unplug this apparatus during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
16. This apparatus shall be connected to a mains socket outlet with a protective earthing connection.
17. When permanently connected, on all-pole mains switch with a contact separation of at least 3mm in each pole
shall be incorporated in the electrical installation of the building.
18. If rack mounting, provide adequate ventilation. Equipment may be located above or below this apparatus but
some equipment (like large power amplifiers) may cause an unacceptable amount of hum or may generate too
much heat and degrade the performance of this apparatus,
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

unDX2IO+
User Manual
Attero Tech, LLC
1315 Directors Row, Suite 107, Ft Wayne, IN 46808
Phone [phone] • Fax [phone]
www.atterotech.com
614-00036
LIMITED FIVE YEAR WARRANTY
The equipment is warranted for five years from date of purchase from Attero Tech, LLC against defects in materials or
workmanship. This warranty does not cover equipment which has been abused or damaged by careless handling or
shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Attero Tech, LLC
will, at our option, repair or replace any defective parts without charge for either parts or labor. If Attero Tech, LLC cannot
correct the defect in the equipment, it will be replaced at no charge with a similar new item. Attero Tech, LLC will pay for
the cost of returning your equipment to you. This warranty applies only to items returned to Attero Tech, LLC, shipping
costs prepaid, within five years from the date of purchase. This Limited Warranty is governed by the laws of the State of
Indiana. It states the entire liability of Attero Tech, LLC and the entire remedy of the purchaser for any breach of warranty
as outlined above. NEITHER ATTERO TECH, LLC NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE
EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF ATTERO TECH, LLC HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF ATTERO TECH, LLC EXCEED THE PURCHASE PRICE OF ANY
DEFECTIVE EQUIPMENT.
This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state.
Note: This equipment has been tested and found to comply with the
limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules
and EN55022. These limits are
designed to provide reasonable
protection against harmful interference when the
equipment is operated
in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with
the instruction manual, may cause harmful interference
to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference,
in which case the user will be required to correct the interference at their own expense.

unDX2IO+
User Manual
Attero Tech, LLC
1315 Directors Row, Suite 107, Ft Wayne, IN 46808
Phone [phone] • Fax [phone]
www.atterotech.com
614-00036
Contents
1 – Overview.....................................................................................................................................................................................................................4
1.1 – What’s in the Box ..................................................................................................................................................... 4
1.2 – Optional Extras......................................................................................................................................................... 4
2 – Device Installation.................................................................................................................................................................................................5
2.1 – Mounting .................................................................................................................................................................. 7
2.2 – Error Reporting......................................................................................................................................................... 9
2.3 – Hardware Connections ............................................................................................................................................. 9
2.3.1 – Balanced Output to a Balanced Input............................................................................................................... 9
2.3.2 – Unbalanced Output to an Balanced Input ........................................................................................................ 9
2.4 – Factory Reset .......................................................................................................................................................... 11
3 – Device Configuration ........................................................................................................................................................................................ 12
3.1 – IP Address Setup .................................................................................................................................................... 12
3.2 – Software Control .................................................................................................................................................... 13
3.3 – 3rd Party Control ..................................................................................................................................................... 13
3.4 – Control Interface Type ........................................................................................................................................... 13
3.4.1 – Using the Command interface ....................................................................................................................... 13
ARCHITECTS & ENGINEERS SPECIFICATION ..................................................................................................................... 14
Device Specifications....................................................................................................................................................... 15

unDX2IO+
User Manual
Attero Tech, LLC
1315 Directors Row, Suite 107, Ft Wayne, IN 46808
Phone [phone] • Fax [phone]
www.atterotech.com
614-00036
1 – Overview
The unDX2IO+ DanteTM Audio Interface is a cost effective XLR‐IO wall plate solution. The unDX2IO+ features two balanced
mic/line XLR inputs, two balanced XLR line outputs, and a further two balanced line inputs on de-pluggable connectors
on the side of the unit. All inputs and outputs can be used simultaneously and all audio channels are available separately
on the Dante network. The unDX2IO+ is designed to fit into all dual gang US junction boxes, mud rings, and old work
brackets. The unDX2IO+ is PoE enabled, so all connectivity (power, control and data) is provided by a single CAT‐5 /6
cable. The unDX2IO+’s size and I/O density make it easy to put Dante connectivity wherever it’s needed.
Figure 1 - unDX2IO+ Front Panel
1.1 – What’s in the Box
The unDX2IO comes supplied with the following
ounDX2IO+ device
oMounting kit
oDecora plate
o6-position depluggable terminal block
1.2 – Optional Extras
The following are available as options for the unDX2IO+ and that may be ordered separately:
ounAX2I - Passive Dual XLR-F single gang Decora wall plate - P/N: 900-00204-01
(Comes with 3-gang Decora cover plate).