aTTo Digital TileRec User manual

TileRec
User’s manual
Disclaimer
Appearance and Buttons
ATTO Digital cannot be held responsible for any use of the TileRec Voice Recorder
without the necessary permission(s) needed for recording. The user is directly
responsible for researching and obeying the applicable laws. Please check the local
laws applicable in your area. Regardless of whether state or federal law governs the
situation, it is almost always illegal to record a phone call or private conversation to
which you are not a party, do not have consent from at least one party, and could not
naturally overhea
naturally overhear. ATTO Digital can’t be held liable for any loss or damage of whatever
nature (direct, indirect, consequential, or other) which may arise as a result of a
person’s use of (or inability to use) our products.
Lanyards Hole
Indicator
Light
REC Button
USB
Reset
Voice Activated Recorder

How to turn ON/OFF
The TileRec allows you to set up time anddate stamp for your recordings and also, to
set up the recording mode you need to use – continuous recording or voice-activated
recording.
Please follow the steps below to set the time stamp and the recording mode.
1
Connect the recorder to a PC, via the USB cable provided in the box and access
the folder RECORD in the partition of the device.
Setting up device
Start Voice Recording
Slide the REC button to ON ( ) direction and the device will start recording. The light
indicator will switch from RED to BLUE to confirm the device is functioning properly.
Stop Voice Recording
ON
OFF
Slide the REC button to OFF (opposite direction from ON) and the device will stop
recording, saving the audio file automatically.

2
In the folder RECORD create a TEXT document with the name time.txt.
a. for Windows PCs you can right-click in the folder RECORD and select NEW -≥
Text Document. Or go to Start menu and open Notepad, create the text file and
then save it to the folder RECORD.
b. for Mac you can either install notepad or go to Mac editor and select the plain
text format for your document in order to save a .txt file.
The first line should reflect current date and time with the format:
yyyymmddhhmmss, as follows:
yyyy – four digits format for year (ex. 2019), mm - is 2 digits month (ex. for May is 05),
dd - 2 digits day (ex. if today is in 3rd - you must put 03). hh - means 2 digit hour format
(24 hours format, not AM or PM)- ex. for 5 PM you must use the digits 17, for 6 AM is
06, etc. ; mm - is 2 digit format for minutes and ss - is 2 digit format for seconds.
If today would be the 1st of October 2019, at
If today would be the 1st of October 2019, at 11:30 AM, here is what you should input
in the time.txt file: 20191001113050 (no spaces in front or after these digits).
The second line reflects the recording mode set up for your device. To set the
device to voice-activated recording please use 1. To set the device to continuous
recording mode, please use 0. To resume:
Voice activated recording mode = 1
Continuous recording mode = 0
The third line is to set the LED light indicator mode. Setting the mode to 1 means
that the blue LED indicator will keep flashing during recording period to signal the
device is working. Setting the value to 0 will mean that the LED indicator will not flash
at all during recording time.
a. Flashes 10 seconds before turning off to signal voice-activated recording mode.
b. Keeps bright for 10 seconds before turning off to signal continuous recording
mode.
1
Blue LED indicator
If the disk space is full, the green indicator will flash fast for 10 seconds before the
device turns off automatically. To resume recording, please make sure you free up
some space on the recorder’s drive. We recommend deleting any old/unnecessary
files or move them to another folder in your computer.
2
Green LED indicator
Understanding LED indicator signals
20191001113050
1
1

Slide the power button to OFF position to make sure your device is turned off before
connecting it to the PC.
Use the USB cable provided in the box to connect the recorder to your computer. If you
need to connect the recorder to an Android phone with USB-C, please use an OTG
connector. You will then have access to the folder RECORD where all your audio files
are saved.
How to connect device to PC
If the RED-light indicator keeps flashing during recording, it means that the battery of
the device is running out and you should recharge it. Please use the USB cord to
connect the recorder to a power source ( PC port or wall charger).
The battery need approximately 1.5 hours for a full charge. When the battery is full,
the RED-light indicator will stop flashing and remains lit.
The recorder’s battery will last up to 24 hours on a full charge.
Charging the recorder

Slide the power button to OFF to make sure the device is turned off and recordings are
properly saved. Connect the recorder to your PC or Android phone via the USB cable.
Connect to PC Connect to Android phone
Playback recordings
Troubleshooting
Once you’ve plugged it in, open „My PC‟ (for Windows computers) or Finder (for MAC),
and double click on the new drive that appears in your system.
Access the folder RECORD where all your audio files are saved and select the one you
need to listen to. You can playback the files in your preferred media player.
If you believe your recorder isn’t working, don’t give up just yet and assume that it is
defective.
1. If you connect the device to your computer and cannot see the partition, please
check if the recorder is turned off.
2. If the device does not charge, please try to use an alternate USB cable (that also
allows data transfer) to connect a power source. Sometimes, even if the USB cable
is working, the computer might enter standby and prevent power flow to the recorder.
Please make sure that your computer is active and the USB port allows charging.
3. If your recorder does not seem to record and the green light is blinking fast, then the
disk space of your device is full and does not allow more data. Please delete
unnecessary files to free up space and resume recording.
4. If the device seems unresponsive during operation, please use a pin or a needle to
press the reset button for 10 seconds. This should restore your recorder’s operation
to normal
IMPORTANT! To protect your recorder’s functionality, please make sure you always
use the “Safely Remove Hardware” (in Windows) or “Eject” (in macOS) when
disconnecting the recorder from your computer.

To extend your voice recorder’s life please make sure you use it properly. Please check
below notes for reference:
1. Please read the manual carefully before operating the device.
2. Do NOT place or store the recorder in spaces with high temperature, damp or dust.
3. This is an electronic device that should be handled with care, avoiding drops, shocks
or other actions that might cause mechanical damage.
4.
4. Back up files regularly on other storage units (eg. your computer) to avoid losing
data due to malfunctions of device or wrongfully operating it.
5. Do NOT disassemble the recorder or replace inner parts by yourself. In case you are
sending the recorder for repairs, please back up your data first. We are not
responsible for the loss of informationcaused by maintenance.
6. Battery recomandations: Please check the applicable laws and recommendations
to make sure you properly dispose the battery of the device. Make sure you keep the
battery under room temperature and try to keep it charged at least to 30%.
7. Avoid using high-power chargers (eg. Smartphone fast-charger) as it may shorten
the battery charging cycles.
8. Even if the device is not used on a regular basis, it is recommended to charge the
battery at least once in 6 months to avoid from being over-discharged.
For any other problem, please contact us:
[email protected] or atto-digital.com/support
Recommendations
Technical Specifications
Size: mm x mm x mm
Weight: g
Power Supply: Polymer Battery 3.7V 240mAh Battery time about 24hours
Recording Format: MP3, 128Kbps
Recording Time: 4GB: about 72hours
8GB: about 145hours
16GB: about 290hours
32GB: about 575hours
Support System: Windows 2000/XP/Vista/7/8/10/Android
Flash Memory: 4GB - 32GB ( FAT32 )
suppor[email protected]