ATZ HDMI-V2-44B User manual

pg. 1 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
1. Introduction
The HDMI 4x4 matrix switcher features four HDMI inputs and four HDMI outputs. It provides true matrix
routing for HDMI signals. It supports the transmission of video (resolutions up to 2160p@60Hz Ultra HD
4:4:4) and supports high resolution digital audio formats such as LPCM 7.1CH, Dolby TrueHD, Dolby
Digital Plus and DTS-HD Master Audio. It works with Blue-Ray players, Set-Top boxes, Home Theater PCs,
and game consoles. Any source is accessible at all times by any display by selecting it via the supplied IR
Remote Control, RS-232, TCP/IP or the selection buttons on the front panel. This device supports all
HDMI 3D formats.
2. Features
HDMI2.0, HDCP2.2/HDCP1.4 compliant
Support video format up to 4k2k@60Hz with 24bit RGB/YCbCr 4:4:4/YCbCr 4:2:2, and up to

pg. 2 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
4k2k@60Hz with 12bit YCBCR 4:2:0
Support color space conversions among RGB, YCbCr4:4:4, YCbCr4:2:2 and xvYCC video formats
Support all HDMI 3D formats up to 2160p@30
Support high resolution VESA mode video format up to QSXGA@60Hz
Support reception of any audio data conforming to the HDMI specification such PCM at up to 192kHz,
compressed audio (IEC 61937), DSD, DST, DTS and HBR
Support simultaneous HDMI Coax and L/R audio outputs
Support smart EDID management
Support RS-232, remote control, on-panel control and TCP/IP Control
3. Package Contents
1 x HDMI 4x4 Matrix Switcher
1 x 12V/2.5A Power Adapter
1 x Operation Manual
1 x Wideband IR Rx cable
1 x HDMI Matrix IR Remote
2 x Mounting ears(Matrix)
1 x RS-232 cable
4. Specifications
Video Bandwidth 594MHz [18Gbps]
Support Video Resolution 480i, 576i, 480p, 576p, 720p, 1080i,1080p24/30/50/60,
2160p24/25/30/50/60;
Input Ports 4×HDMI, 1×IR Receiver, 1×RS-232,
1xRJ-45(Control)
Output Ports 4×HDMI, 4×Toslink, 4×L/R
HDMI connector Type A 19 pin female
RJ-45 connector WE/SS 8P8C
3.5mm connector IR Receiver
ESD Protection Human-body Model:
± 8kV (Air-gap discharge)
± 4kV (Contact discharge)
Power Supply 12V/2.5A DC (US/EU standards,
CE/FCC/UL certified)

pg. 3 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
Dimensions 440 mm (W)×200 mm (D)×45 mm (H)
Weight 1820 g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0 ºC~40 ºC/32 ºF~104 ºF
Storage Temperature −20 ºC~60 ºC/−4 ºF~140 ºF
Relative Humidity 20~90 % RH (non-condensing)
Power Consumption 30 W(max)/0.5w(Standby)
5. PANEL FUNCTIONS
5.1 Front Panel
1. LCM: Display the information of each input and output setting and EDID management.
2. IR: IR Receiver window (accepts the remote control signal of this device only).
POWER: Press this button to power the device on/off. The LED will illuminate green when the power is
on, red when it is in 'Standby' mode.
LOCK: Press this button to lock all the buttons on the panel, press again to unlock.
3. OUTPUT/INPUT: Press the OUTPUT and INPUT button to select the output corresponding input.
For example: Press OUPUT ALL > INPUT 1, The OUTPUT A, B, C, D will be set to INPUT 1.
Press PTP button, The OUTPUT A, B, C, D will corresponding INPUT 1, 2, 3, 4.

pg. 4 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
4. EDID: Smart EDID management, the LCM will display the EDID operation.
Press the MENU button enters the EDID management window. Press UP or DOWN button to select the
needed EDID setting. Press ENTER button to download EDID into input source, it can easy
download any EDID setting to any input port.
Note: The EDID mode table as below
EDID Mode
EDID Description
1
1080p, 2CH AUDIO
2
1080p, DOLBY/DTS 5.1
3
1080p, HD AUDIO
4
1080i, 2CH AUDIO
5
1080i, DOLBY/DTS 5.1
6
1080i, HD AUDIO
7
3D,1080p, 2CH AUDIO
8
3D, 1080p, DOLBY/DTS 5.1
9
3D,1080p, HD AUDIO
10
4K30_444, 2CH AUDIO
11
4K30_444, DOLBY/DTS 5.1
12
4K30_444, HD AUDIO
13
4K60_420, 2CH AUDIO
14
4K60_420, DOLBY/DTS 5.1
15
4K60_420, HD AUDIO
16
4K60_444, 2CH AUDIO
17
4K60_444, DOLBY/DTS 5.1
18
4K60_444, HD AUDIO

pg. 5 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
19
Copy from HDMI OUTPUT A
20
Copy from HDMI OUTPUT B
21
Copy from HDMI OUTPUT C
22
Copy from HDMI OUTPUT D
EDID. What is it and what is it used for?
Under normal circumstances, a source device (digital and analog) will require information from a connected
device/display to know what resolutions and features are available. The source can then cater its output to
send only resolutions and features that are compatible with the attached device/display. This information is
called EDID (Extended Display Information Data)
and a source device can only accept and read one EDID from a connected device/display. Likewise, the source
can only output one resolution to a connected device/display.
Why is EDID so important with the HDMI Matrix?
The Matrix is complex piece of technology that replicates and switches between multiple inputs and outputs.
Each connected source device will require one EDID to read. EDID management is carefully handled by HDMI
Matrix to provide a single EDID for each source to read.
What options do I have to manage the EDID in the HDMI Matrix?
First, it is important to note that each source device can only output one video/audio signal type. This includes
resolutions and timings. When multiple devices/displays are used, such as with the HDMI Matrix, it is
important to use devices/displays that have similar or compatible resolutions/features. This will ensure that
the single video/audio signal produced by the source device is accepted by all of the connected output
devices/displays. The user has the option, through the EDID management window, to choose how the unit will
manage the EDID from multiple HDMI devices/displays. Therefore the user has some control over the
resolutions/features that the source devices will output. The HDMI Matrix has a multiple EDID management
modes that will control how the EDID information from multiple devices/displays are combined, ignored, and
routed.

pg. 6 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
5.2 Rear Panel
1. PC CONTROL
TCP/IP: This port is the link for TCP/IP control and connects to an active Ethernet link by an RJ-45 cable.
RS232: Connect to a PC or control system by D-Sub 9-pin cable for the transmission of RS-232 commands.
2. HDMI INPUT: Connect to the HDMI sources device such as a DVD player or a Set-top Box by HDMI cable.
3. AUDIO OUPUT: The coaxial and L/R audio output to audio amplifiers or speakers.
4. HDMI OUTPUT: Connect to HDMI equipped TVs or monitors.
5. IR EXT: If the front IR sensor of unit is obstructed or the unit is installed in a closed area out of infrared line
of sight, the IR RX receiver included can be inserted into the IR EXT port at the rear to extend the IR sensor
range and enable local control of the matrix.
6. DC POWER INPUT: Connect to 12V/2.5A DC power adapter.

pg. 7 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
6. Remote Control
1. Press this button to power on the matrix or set it to standby mode.
2. Press these buttons to select output A, B, C, D for input 1, 2, 3, 4 ports.

pg. 8 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
7. PC Controller user guide
Installation
Matrix controller is green software. Just copy MatrixController.exe to PC which is used to control the Matrix by
RS232 COM port or TCP/IP to complete installation.
Preparation
Connect PC and Matrix by RS232 cable (headers of both sides of cable should be FEMALE) or TCP/IP(local
area network)
Power-up Matrix
Double click MatirxController.exe icon to run it
How to control Matrix
“General” page
1. Select RS232 COM or TCP mode
2. Select RS232 COM port
3. Click to connect or disconnect PC with Matrix
4. Select Matrix IP
5. Connect to Matrix IP
6. Search Matrix IP

pg. 9 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
7. Configure Matrix IP and MAC
8. Click to reset to the factory settings
9. Reboot Matrix system
10. Device information display area
11. Click to refresh device status: include device information displayed in 10 areas and Input/output settings on
“Matrix” page
12. Click to clear device information
13. Enable or disable Beep
14. Power on/off Matrix system
Configure TCP
After action of 7, edit form will pop-up as below:
1. Select auto or static IP
2. Set the Matrix IP
3. Set the Matrix MAC
“EDID control” page

pg. 10 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
The controller has 3 methods to set the EDID mode. Manual mode, Copy mode and open EDID file mode.
1. Select the needed EDID to input port and click set button to download EDID to the selected HDMI input port.
2. Copy the selected HDMI output EDID and click set button to download EDID to the selected HDMI input port.
3. Open the user define EDID file and click set button to download EDID to the selected HDMI input port.
4. Click the status button to refresh input EDID status.

pg. 11 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
“Matrix” page
1. LED which display Input number for respective Output
2. Click to select Input port for respective Output port
3. Click to select previous or next Input port for respective Output port
4. Select ON/OFF to enable/disable ARC function
“FW upgrade” page

pg. 12 All specifications are subject to change without prior notice.
© Copyright ATZ 2015
Model :ATZ HDMI-V2-44B
Description:4x4 HDMI2.0 Matrix Switch 18Gbps 4K@60 (4:4:4)
1. Click to open FW file(file extension is “.fw”)
2. Display the FW file path
3. Display the progress of the software upgrade
4. Click to upgrade the Matrix software
5. Display the message of the software upgrade
8. Basic Installation Diagram
1. Connect up to 4 sources such as a Blue-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver,
etc. to each HDMI input port on the unit. Do not hot plug! Insert and extract cables carefully with the
power switch off. Connecting and disconnecting while the unit is powered can result in damage to
circuitry.
2. Connect each HDMI output to high-definition displays such as a HDTV or HD projector that has HDMI
input. Note that high-speed HDMI cables are recommended for the distances that are required for each
connection.
3. Plug in IR receiver to the port of the IR EXT on rear unit if need.
4. Plug in DC power adapter firstly, followed by each display device and source device.