Aube Technologies TH132 A User manual

Thank you for choosing the Aube TH132, a programma-
ble thermostat that provides both energy savings and total
comfort.
nDAY/HOUR/MIN—Set the day and clock settings.
oPGM—Program the schedule (programs).
pMODE—Select the operating mode.
RETURN—To exit a function.
qTo configure temperature setpoints:
Comfort, Economy and Vacation.
rAdjust the floor temperature limit (AF only).
s—Increase and decrease temperature.
t—Indicates the number of the current
program when Automatic mode is enabled.
uCurrent operating mode (auto / manual ). In
Auto mode, the program’s associated setpoint icon is
also displayed ( ).
vIndicates the room OR floor temperature.
wHeating indicators (see “Temperature Control”
below).
TH132-A
This model has been designed to control a room’s ambi-
ent temperature.
The TH132-A has one temperature sensor located in the
control module.
TH132-AF
This model is designed to use a floor sensor to control the
room temperature.
The TH132-AF has two temperature sensors:
• The first one, installed in the control module, controls
the ambient temperature.
• The second one, installed in the floor (and connected
to the power base), limits the temperature of the floor
(the default setting of this limit is 82°F).
TH132-F
This model is designed to control floor heating systems.
The TH132-F has one temperature sensor installed in the
floor (sensor is connected to the power base).
The TH132 has two switches, located on the upper-left
part on the rear of the control module, which are used to
set the following options:
Early Start
When the Early Start function is enabled (disabled by
default), the TH132 calculates the optimum system start
time to obtain the desired temperature by the set time. To
enable this function:
Position switch #1 down.
Note: When this function is enabled, the
system can be activated before the pro-
gram’s start time.
Temperature Display
By default, the TH132 displays the temperature in °C. If
you wish to change to °F:
Position switch #2 up.
Note: When you switch from °C to °F or vice
versa, the , and setpoints must be
redefined.
Control Module
TH132 A/F/AF
Owner’s Guide
TH132 Description
Models Overview
Configure the Switches
Align the bracket tabs on the control module with the
holes located on top of the power base.
This control module must be installed on a PB130 series
power base.
Note: Keep the thermostat's air vents clean and free from
obstructions.
Note: The screw cannot be removed completely.
On the first installation, the screen displays:
0:00, MO, and temperature (room/floor).
For Floor Heating Installations:
One of the two following messages may be dis-
played when a problem occurs:
LO: The floor temperature is below 32°F (0°C), or
the temperature sensor is defective, or not
connected.
The heating indicator is displayed and
the relay is closed (energized).
HI: The floor temperature is above
140°F (60°C), or the temperature sensor is
defective.
nSet the time (HOUR - MIN).
oSet the day (DAY).
If you remove the module from its base for more than
2 hours, the time and day will have to be reprogrammed.
Comfort and Economy Setpoints
These setpoints are associated with the schedule’s pro-
grams (prog. 1 & 3 = Comfort, prog. 2 & 4 = Economy)
and are preprogrammed as follows:
A & AF models— 68°F, 64°F
F model— 82°F, 68°F
To modify a setpoint:
nSet the temperature using and press and hold the
or button until it is displayed on the screen.
oPress MODE/RETURN to exit.
Vacation Setpoint
The vacation setpoint is associated to the Vacation oper-
ating mode and is preprogrammed to 50°F. To modify this
setpoint, repeat above steps.
Floor Temperature Setpoint (AF model only)
The floor temperature limit is preprogrammed to 82°F to
avoid damage to your floor.
To modify, press the adjustment button (below ) using a
pointed object, set the desired temperature using and
press MODE/RETURN to exit.
The TH132 offers three operating modes:
Automatic —Executes the schedule.
nPress MODE to select . The current
program number is displayed.
You can temporarily bypass the current
program by setting a specific temperature setpoint
or by selecting one of the pre-defined setpoint
buttons ( ). The new setpoint will be maintained
until the beginning of the next program.
Manual —Maintains a constant temperature.
nPress MODE to select .
oSet temperature or select one of the pre-
defined setpoint buttons ( ).
Vacation —Maintains the Vacation setpoint
during a prolonged absence.
Press .
Install the Control Module
Power base
Control module
Air vents
Air vents
First Power ON
Set the Time and Day
Adjust the Temperature Setpoints
Select the Operating Mode
400-132-000-A

The schedule is used with the Automatic mode. The
schedule controls the heating system to automatically
switch between the Comfort and Economy temperature
setpoints at the times you have programmed.
The schedule consists of 4 programs per day defined as
follows:
To enter the programs’ start time
To shorten programming, you simply have to enter the
start time for each program.
nPress PGM.
oPress DAY to select the day (hold for 3 seconds to
select all days of the week).
Note: It is sometimes faster to program the same sched-
ule for the entire week and then to modify the exception
days.
pPress PGM to select the program number (e.g. 1).
qPress HOUR and MIN to set the start time.
rRepeat steps 3 to 4 for remaining programs (e.g. 2, 3
and 4).
sPress MODE/RETURN to exit.
Note: After 60 seconds of inactivity, the thermostat will
automatically exit programming mode.
To clear a program time:
When you clear a program time entry, the TH132 will
maintain the temperature setpoint of the last executed
program until the beginning of the next program.
nRepeat steps 1 to 3 above.
oPress CLEAR to erase the time entry. The time por-
tion of the LCD indicates --:-- when the program is
inactive.
pPress MODE/RETURN to exit.
Programming Example
Comfort :
• Monday to Friday, between 6:00 and 8:30 and
between 16:00 and 23:00.
• Saturday and Sunday, between 6:00 and 23:00.
Economy :
• Monday to Friday, between 8:30 and 16:00 and
between 23:00 and 6:00.
• Saturday and Sunday, between 23:00 and 6:00.
To program this schedule
nPress PGM.
oPress and hold DAY for 3 seconds to select all days
of the week.
pPress PGM to select program 1.
Set the time (6:00) using the HOUR and MIN buttons.
qPress PGM to select program 2.
Set the time (8:30) using the HOUR and MIN buttons.
rRepeat step 4 for remaining programs:
program 3 (16:00) and program 4 (23:00).
sWhen all programs are configured, press MODE/
RETURN to exit.
To erase programs 2 and 3 for Saturday and
Sunday
nPress PGM.
oPress PGM to select program 2.
pPress DAY to select SAturday (SA).
qPress CLEAR to erase the time (--:--).
rPress DAY to select SUnday (SU).
sPress CLEAR to erase the time (--:--).
tPress PGM to select program 3.
uRepeat steps 3 to 6.
vPress MODE/RETURN to exit.
Programs Setpoint Time i
i. The programs’ start time can be different for each day of the week.
Wake-up
Leave home
Back home
Night
Program Your Schedule
Programs MO TU WE TH FR SA SU
6:00 6:00 6:00 6:00 6:00 6:00 6:00
8:30 8:30 8:30 8:30 8:30 --:-- --:--
16:00 16:00 16:00 16:00 16:00 --:-- --:--
23:00 23:00 23:00 23:00 23:00 23:00 23:00
Temperature Control
The TH132 thermostat works differently than conventional
electromechanical thermostats.
It is equipped with a proportional integral adaptive (PIA)
controller which determines heating cycles by analyzing
the temperature behavior history within the room.
The PIA controller reduces temperature swings providing
accurate temperature control while increasing user com-
fort.
The controller determines the amount of power required
by the heating system to maintain the setpoint tempera-
ture.
When the heating system is activated, one of the following
icons is displayed:
Technical Specifications
Model: TH132 A / AF / F
Display range: 32°F to 140°F (0°C to 60°C)
Setting range (ambient): 40°F to 86°F (5°C to 30°C)
Setting range (floor): 40°F to 104°F (5°C to 40°C)
Pre-programmed temperature setpoints:
Comfort: A/AF: 68°F (20°C) and F: 82°F (28°C)
Economy: A/AF: 64°F (18°C) and F: 68°F (20°C)
Vacation: A/F/AF: 50°F (10°C)
Floor limit: AF: 82°F (28°C)
Temperature resolution display scale:0.1°
Storage:-4°F to 120°F (-20°C to 50°C)
Software: Class A
Controller: Electronic
Temperature control: Proportional integral adaptive,
15-minute heating cycles
Programming protection: Protected memory
Clock protection: 2 hours
Size (H/W/D): 3.3 x 3.1 x 0.5 in (83 x 79 x 13 mm)
Warranty
AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY
This product is guaranteed against workmanship defects
for a two-year period following the initial date of purchase.
During this period, AUBE Technologies Inc. will repair or
replace, at our option and without charge, any defective
product which has been used under normal conditions.
The warranty does not cover delivery costs and does not
apply to products poorly installed or randomly damaged
following installation.
This warranty cancels and replaces any other
manufacturer's express or implied warranty as well as any
other company commitment. AUBE Technologies Inc.
cannot be held liable for related or random damages
following the installation of this product.
The defective product as well as the purchase invoice
must be returned to the place of purchase or mailed,
prepaid and insured, to the nearest shipping address.
If you have any questions concerning the programming of
the TH132 programmable thermostat, call our technical
support team at:
1 to 20% 21 to 40% 41 to 60% 61 to 80% 81 to 100%
705 Montrichard
Saint-Jean-sur-Richelieu
Quebec, Canada J2X 5K8
Tel.: [phone]
Toll Free: 1-800-831-AUBE
Fax: [phone]
Email: [email protected]
10 rue Ampère
95500 Gonesse
France
33 (0) 1 34 07 99 00
33 (0) 1 34 07 99 19
[email protected]
For more information on our products, visit us at:
www.aubetech.com
As an ENERGY STAR®partner, Aube Technologies has
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
26/08/2003 400-132-000-A

Included Parts
!One (1) PB130-230 power base
"One (1) floor sensor (for AF and F control modules only)
#One (1) wall plate (optional, in certain countries)
PB1 30-230
Installation Instructions
230 V Line Voltage Power Base
Technical Specifications
Model: PB130-230
Supply: 230 VAC, 50 Hz
Load: 16 A maximum (resistive only)
Power: 3680 Watts (NI) @ 230 VAC
Approval: EN60730-2-9 / EN50081-1 / EN50082-2
Storage: -20°C to 50°C
Protection:Class2
Protection degree:IP20
Automatic action:Type1.B
Environment: Normally polluted
Size(H•W•D): 2.95 x 2.95 x 0.55 in. (75 x 75 x 14 mm)
NOTE: The terminals are designed to handle a cross-section of
wire measuring 0.33 to 3.1 mm2.
AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY
This product is guaranteed against workmanship defects for a two-year period following
the initial date of purchase. During this period, AUBE Technologies Inc. will repair or
replace, at our option and without charge, any defective product which has been used
under normal conditions.
The warranty does not cover delivery costs and does not apply to products poorly
installed or randomly damaged following installation. This warranty cancels and
replaces any other manufacturer's express or implied warranty as well as any other
company commitment.
AUBE Technologies Inc. cannot be held liable for related or random damages following
the installation of this product. The defective product as well as the purchase invoice
must be returned to the place of purchase or mailed, prepaid and insured, to the
nearest location.
If you have any questions concerning the installation of the
PB130-230 power base, contact our technical support team at:
705 Montrichard
Saint-Jean-sur-Richelieu
Quebec, Canada J2X 5K8
Tel.: [phone]
Toll Free: 1-800-831-AUBE
Fax: [phone]
Email: serv[email protected]om
10 rue Ampère
95500 Gonesse
France
33 (0) 1 34 07 99 00
33 (0) 1 34 07 99 19
advaub[email protected]om
For more information on our products, visit us at
www.aubetech.com
Introduction
The PB130-230 power base is designed to power a TH13x
Series control module. The resistive load must not exceed
3680 watts (NI) @ 230 VAC (16 A).
Installation Guidelines
Turn off power to the heating system at the main power panel
to avoid electrical shock. Installation should be carried out by
an electrician.
ߧ All work must conform to the applicable country standards for
electrical installations and wiring.
ߧ This thermostat should be connected on a circuit equipped
with a fuse or a circuit breaker. It must be installed on a certi-
fied electrical box.
ߧ For a new installation, choose a location about 1.5 m above
the floor.
ߧ For electric baseboards, convectors and fan-forced heaters,
the thermostat must be installed facing the heating system.
ߧ The thermostat must be installed on an inside wall.
ߧ Avoid locations where there are air drafts (top of staircase, air
outlet), dead air spots (behind a door), direct sunlight or con-
cealed chimneys or stove pipes.
!Remove the screw holding the
control module to the power base
and lift the lower part upwards.
The screw cannot be completely
removed.
"If you have a wall plate: Before making
the connections, make sure that the base
covers the electrical box entirely. If not,
insert the wall plate on rear of the base.
NOTE: The wall plate can be used for aesthetic
purposes only.
#Connect the wires:
•Power (L, N):
Terminals 1 and 5
•Load (L, N):
Terminals 2 and
4
see notes 1 & 2
•Pilot Wire (F.P.):
Terminal 3
see note 3
•Floor sensor:
Terminals 6 and 7
(no polarity needs
to be respected)
Note 1 If the load is driven through a contactor, it is recommended
to install a snubber at the contactor’s coil terminal to
extend the contactor’s life expectancy and ensure a good
operation of the thermostat.
Note 2 Compatible with TH131 control module only.
Note 3 The floor sensor wire cannot lay across or next to any
heater wires. For maximum performance, the sensor must
be centered between the wires at a maxi-
mum temperature of 80°C.
$Push wires into the electrical box and
secure the base to the electrical box
anchorage. The head of the screw
must be less than 2 mm thick.
%BEFORE mounting the control
module onto the base, configure the
switches (if any) and install the con-
trol module onto the base (refer to the
user guide).
&Return power to the heating system.
19/01/2004 400-130-001-B
Installation and Wiring
WARNING: this power base must be used only with 15-minute
heating cycles (temperature control). Depending on the selected
control module, make sure that the switch is set at 15 minutes.