Audio Technica AT2020USB-XP User manual

AT2020USB-XP
Cardioid Condenser USB Microphone
User Manual
English
Safety precautions
Cautions for the headphones
Cautions for charging case
Cautions for rechargeable battery
Notes on use
About water-resistant (drip-proof) performance
For a more comfortable Bluetooth communication experience
Part names and functions
Headphones
Charging case
Accessories
Charging the battery
Charging the headphones and charging case
Charging headphones without the USB charging cable
Power supply ON/OFF
Turning on the product
Turning off the product
Connecting via Bluetooth
Pairing a Bluetooth device
Pairing with Fast Pair
About pairing
Wearing the product
Touch sensors
Unlocking
Using the product
Listening to music
R (right) side headphone touch sensor operations
L (left) side headphone touch sensor operations
Talking on the phone
R (right) side headphone touch sensor operations
L (left) side headphone touch sensor operations
Hear-through mode
Low latency mode
Auto power off function
Indicator lamp display
Pairing
Connecting
Battery level
Voice guidance
Cleaning
Eartips
Eartip size
Replacing the eartips
Resetting
If the product operates abnormally (reset)
Troubleshooting
Specifications
Headphones
Microphone
Communication specifications
Other
Trademarks

1
Safety precautions
Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure
safety, observe all warnings and cautions while using the product.
Cautions for the product
•Do not subject the product to strong impact to avoid malfunction.
•Do not disassemble, modify or attempt to repair the product.
•Do not handle the product with wet hands to avoid electric shock or injury.
•Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.
For customers in the USA
FCC Notice
Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Contact
Responsible Company: Audio-Technica U.S., Inc.
Address: 1221 Commerce Drive, Stow, Ohio 44224, USA
Tel: [phone]

2
For customers in Canada
ISED statement
CAN ICES-3(B)/NMB-3(B)

3
Notes on use
•Be sure to read the connected device’s user manual before use.
•When the product is used for a long time, the product may become discolored due to ultraviolet light (especially
direct sunlight) and wear.
•Use the included USB cable for connection.
•Make sure to hold the plug when connecting and disconnecting the USB cable. The USB cable may become severed
or an accident may occur if you pull on the USB cable itself.
•When using the USB cable, be careful not to twist it to prevent damage to the USB cable.
•Do not wind the USB cable at the base of the plug to prevent a disconnection.
•Do not use a USB hub or USB extension cable.
•When plugging the USB cable into the microphone and the connected device, check that the connector is facing in
the correct direction before inserting it straight. Inserting the plug diagonally may cause a malfunction.
•When not in use, disconnect the USB cable from the product.
•Make sure that no foreign matter enters inside the mesh part of the product. Performance may be degraded.
•Depending on the surface treatment of the table on which the product is installed, the desk stand may leave marks
on the table.
•For important recordings, perform a trial recording beforehand to make sure that the sound is recorded correctly.
•Operation is not guaranteed with all computers.
•Operation cannot be guaranteed in a home-built computer, personal OS upgrade, or multi-boot environment.
•Audio-Technica will not be liable in any way for any loss or damage to software or data connected to the product.

4
Part names and functions
Microphone
➊Microphone
➋Mute indicator lamp
Lights blue when audio input is enabled. It lights red when the microphone is muted.
➌Mix control dial
Adjusts the balance of the volume level of the sound coming from the computer and the monitored volume level of the
audio being input (voice).
➍Touch sensor for mute
Turns the muting of the microphone on/off.
➎Automatic gain control indicator lamp
Lights when the automatic gain control function is on.
➏Headphone level control dial
Adjusts volume of headphone output.

5
❼Noise-reduction indicator lamp
When the noise-reduction function is on, the noise-reduction indicator lamp lights in three levels depending on the level.
❽Automatic gain control button
Turns the automatic gain control function on/off. When the function is turned on, the gain is automatically corrected
when the input signal is excessive to prevent output distortion.
➒Noise-reduction button
Turns the noise-reduction function on/off. When turning it on reduces ambient steady noise. The function level can be
set in 3 levels each time the button is pressed.
➓USB terminal (USB Type-C™)
Use to connect the included USB cable.
⓫3/8" Stand mounting screw hole
Use when attaching the stand.
⓬Headphone jack (3.5 mm (1/8") stereo mini-jack)
Use to connect headphones.

6
Included accessories
➊Stand
➋USB cable (USB Type-C to USB Type-A)
➌3/8"-16 to 5/8"-27 threaded adapter
➍USB conversion adapter (USB Type-A to USB Type-C)
➎Pop filter (AT8175)

7
Setting up the product
For best results, set up the product so that it is facing the sound source. When using it to record voices, place it directly
in front of the speaker/singer. Do the same thing when recording sound such as acoustic guitar, drums, or piano. Before
using the product, try setting it up in various positions, to discover how best to record sound in your current environment.
Attaching the stand
You can use the stand to place the product on a table or a similar surface.
1Attach the stand to the mounting screw hole on the product, and then turn the screw to secure the parts. Adjust
the angle of the product, and then turn the grip of the stand to tighten it.
Note •Use the included 3/8"-16 to 5/8"-27 threaded adapter when installing the product on a commercially
available microphone stand.

8
Attaching the pop filter
1Install the pop filter while slightly widening the mounting area to avoid damaging the microphone.

9
Connection procedure
➊USB conversion adapter (USB Type-A to USB Type-C)
➋USB Type-A
➌Headphone input plug
➍USB Type-C
➎Audio-Technica logo
1Connect the USB cable (USB Type-C side) to the USB terminal on the underside of the product.
2Connect the USB cable (USB Type-A side) to the computer.
•If necessary, use the USB conversion adapter (USB Type-A to USB Type-C) depending on the USB terminal of
the computer you are using. Use the USB conversion adapter for the USB terminal of the computer side. Do
not connect it to the USB terminal of the product side.
•If you are using Windows, refer to "Computer settings (Windows)" (p. 1010) to do the settings.
•If you are using Mac, refer to "Computer settings (macOS)" (p. 35) to do the settings.
•Make sure that the mute indicator lamp lights blue (ready for audio input).
3If you are using headphones, connect the headphones to the headphone jack.