Audio Technica 60th ANNIVERSARY AT-LP2022 User manual

Contents
Preparation
Use the included gloves to avoid fingerprints on the turntable.
1 With the turntable turned off, set the platter.
Motor pulley
2 Attach the drive belt to the motor pulley.
3 Level the turntable.
4 Insert the headshell into the tonearm, and remove the
cartridge’s protector.
Protector
5 Attach the counterweight to the back of the tonearm, and
slowly turn it counterclockwise (to the left).
6 Unlatch the clamp.
Clamp
7 Turn the counterweight to adjust the tonearm’s balance so that
the tonearm is level when you release the headshell.
Tonearm
8 Set the tracking force gauge ring to the “0” position.
After that, turn the counterweight and the tracking force gauge
ring together counterclockwise (to the left) to the “2” position.
0
2
Tracking force gauge ring
9 Set the anti-skate control dial to “2”, the same value as the
tracking force value.
Anti-skate control dial
Dust cover hinges Headshell with VM stereo cartridge
Counterweight 45 RPM adapter AC adapter RCA audio cable
Hexagonal wrench
(For tonearm height adjustment) Gloves
Turntable body
Dust cover
Quick Start Guide
Belt-Drive Turntable
Guide de démarrage rapide
Tourne-disque à entraînement par courroie
Kurzanleitung
Riemenbetriebener Plattenspieler
Guida rapida
Giradischi
Guía de inicio rápido
Giradiscos de tracción por correa
Guia de início rápido
Toca-discos acionado por correia
Краткое руководство по установке
Проигрыватель с ременным приводом
快速启动指南
皮带传动唱盘机
快速入門指南
皮帶驅動式黑膠唱機
간편 사용 설명서
벨트 드라이브 턴테이블
Quick Start Guide
AT-LP2022
Back side with hexagonal nut
Drive belt
Platter (with drive belt)
(Remove the protective sheet before use.)
Replacement stylus
(AT-VMN95SH CL)
User Manual (Online Manual)
https://www.audio-technica.co.jp/document/AT-LP2022/
Default.html

Connection
Connect the turntable to the PHONO input of a phono equalizer or an amplifier with a built-in phono
equalizer.
ONON
PHONO
L R
RCA audio cable AC adapter
After all equipment is
connected, turn the
turntable on.
Phono equalizer, etc.
Play
1 Remove the cartridge’s protector.
2 Turn the turntable on, place the record, and use the control
knob to select the speed.
At 33-1/3 RPM
Control
knob
At 45 RPM
45 RPM
adapter
3 Raise the tonearm by lifting the tonearm lift control lever to the
UP position.
Tonearm lift
control lever
4 Position the tonearm over the desired location (groove) on the
record.
5 Lower the tonearm by moving the tonearm lift control lever to
the DOWN position.
Stop
1 Lower the volume of the connected device (amplifier, etc.).
Amplifier, etc.
2 Raise the tonearm by lifting the tonearm lift control lever to the
UP position.
Tonearm lift
control lever
3 Return the tonearm to the tonearm rest.
4 Lower the tonearm by moving the tonearm lift control lever to
the DOWN position and fix it with the clamp.
5 Turn the control knob to the "STOP" position.
6 Attach the cartridge’s protector.
7 Turn the turntable off.
OFFOFF
Replacing the stylus
A replacement stylus (AT-VMN95SH CL) is included with the product.
1 With the turntable turned off and the AC adapter unplugged
from the outlet, release the headshell from the tonearm.
2 After removing the cartridge's protector, remove the stylus by
pulling in the direction of the arrow without touching the
cantilever, stylus tip, and magnets.
Pull
3 Mount the new replacement stylus to the cartridge.
Align the position of the inner protrusion.
4 Mount the headshell onto the tonearm.
5 Adjust the tonearm balance and tracking force.
Cleaning
After turning the turntable off and unplugging the AC adapter from the outlet, clean the turntable as
necessary.
For details about turntable and cartridge care accessories, visit https://www.audio-technica.com.
Stylus
Record
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
www.audio-technica.com
©2022 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com 162502540-01-01 ver.1 2022.06.15