Audiovox VBP700 User manual

VBP700VBP700
VBP700VBP700
VBP700
PORTABLE 7" LCD MONITOR AND DVD PLAYER
IN A BAG

Notice:
This Product incorporates copyright protection technology that is pro-
tected by method claims of certain U.S. Patents and other intellectual
propertyrightsownedbyMacrovisionCorporationandotherrightsown-
ers. Use of this copyright protection technology must be authorized by
MacrovisionCorporation,andisintendedforhomeandotherlimitedview-
ing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
An LCD panel and/or video monitor may be installed in a motor vehicle
and visible to the driver if the LCD panel or video monitor is used for
vehicle information, system control, rear or side observation or naviga-
tion. If the LCD panel or video monitor is used for television reception,
video or DVD play, the LCD panel or video monitor must be installed so
thatthesefeatures will onlyfunctionwhenthe vehicle is in“park”orwhen
the vehicle’s parking brake is applied.
An LCD panel or video monitor used for television reception, video or
DVD play that operates when the vehicle is in gear or when the parking
brake is not applied must be installed to the rear of the driver’s seat
where it will not be visible, directly or indirectly, to the operator of the
motor vehicle.

3
A. Introduction
Thankyou for selectingthe VBP700 portableDVDplayer in abag.
The main features include a 7" Screen (16:9Aspect Ratio) Liquid
Crystal Display (LCD) monitor and a DVD player. The unit applies
thelatest stateof the artelectronics and isdesigned forusein ho-
tels,officeshomeorvehicle.Theunit isconstructedtoprovideyears
ofreliable,trouble-free service,andiscompact sothatyou cantake
it with you anywhere and is designed for quick and easy
installation.Pleasereadthe entire instructionmanualsuppliedwith
thisproductpriorto operation. Thedocumentationwillassistyouin
installing the system properly to obtain the best equipment perfor-
mance. Allmanualsshouldbestoredforlateruse.
B. Cautions and Warnings
1. Placement
To prevent fire or electric shock, do not expose this appliance to
rain or moisture. Do not place the set on an unstable cart, stand,
tripod,bracketor table topreventitfrom falling. Keep theunitaway
fromstrong magnets, heatsources,direct sunlight,excessivedust.
If the unit is brought directly from a cold to a warm location, mois-
ture may condense inside the unit. When you move it from a cold
to a warm location, wait for about one hour before operating the
unit,orremovethedisc and leave the unit turned on untilthemois-
ture evaporates.
2. Installation
Ensure that the VBP700 is installed in accordance with the in-
structions and illustrations provided in this manual.
3. Object and Liquid
Do not push objects of any kind into the unit through openings; do
not spill or spray liquid of any kind on or in the system (this may
result in a fire or electric shock). Do not place anything heavy on
the unit. To ensure proper ventilation and proper operation, never
cover or block the slots and openings with a cloth or other mate-
rial.
4. Disassembly
Do not attempt to disassemble the cabinet. There is a risk of elec-
tric shock and/or exposure to Laser Radiation. Contact qualified
service personnel if your system is in need of repair.

4
5. Cleaning Unit
Whencleaning,make surethesystemis unplugged fromthepower
source. Do not use liquid cleaners or aerosol cleaners. Use a
cloth lightly dampened with water for cleaning the exterior of the
system only.
6. Disc
Do not use irregularly shaped discs such as heart or star-shaped
discs as they may cause the unit to malfunction. Do not stick pa-
per, tape or glue on the disc. Do not expose the disc to direct sun-
light or heat sources such as hot air ducts. Do not touch the sur-
face of disc. Handle the disc by its edge. Clean the disc by wiping
the disc from the center out with a cleaning cloth. Remove the disc
from the unit and store it in its case after playing. Some playback
operations of discs may be intentionally fixed by software produc-
ers. Since this unit plays discs according to the disc contents the
software producers designed, some playback features may not be
available.Also refer to the instructions supplied with the discs.
C. Contents
1. 1 x 7’’ LCD Monitor & DVD Player Combo
2. 1 x AC to DCAdapter
3. 1 x Remote Control w/Battery
4. 1 x Instruction Manual
5. 1 x Audio/Video Input Cable
6. 1 x Audio/Video output Cable
7. 1 x Power Adapter w/Built-In FM Modulator
8. 1 x Mounting Bag w/Straps
9. 1 x Carrying bag
10. 1 x Rechargable Battery Pack (Part Number VBB7080)
OPTIONAL:
Wireless IR headphones (Part Number IRHSCS)
D. Powering and installation
1. Powering the system indoors (Refer to Figure 1)
Plug one end of the AC to DC adapter into the DC 9V jack on the
rightsideofthe main unit, then plug the otherendintothe120VAC
power receptacle.

5
2. Powering the system in a car
Plug one end of the cigarette lighter adapter into the DC 9V jack on
the unit, then plug the other end into the cigarette lighter socket.
Figure 1
3. Powering the system with rechargeable Battery
Please refer to K. * Rechargeable Battery Installation and Use
(Page 33 and 35).
E. Installation Prior to installation
Make sure that the unit is placed into the bag with the clear plastic
coveringaroundDVD door, Load disc into the DVD compartment and
then fasten the Velcro strap across the top portion of the unit. If you
are installing the bag onto the seatback you will need to attach the
supplied Seat Standoff to the back of the mounting bag with the
Velcro bands to obtain the proper viewing angle as shown in Figure.2

6
1.Installing the System onto the seat back in a car
(Refer to Figure 2)
Figure 2
1). Take one of the supplied straps from the carrier bag. Connect
the latch to one of the upper metal rings on the mounting bag.
Connect the “S” hook to the other upper metal ring and place the
loop over the headrest. Adjust the strap until the bag is firmly
secured.
2). Take another strap from the carrier bag, and connect the latch to
the lower metal ring on the left side of the bag. Attach the “S”
hooktothesameringafterloopingthestraparoundtheseatrail.
Repeat this process for the right side. In some vehicles, it may
be necessary to attach the “S” connector to the rail directly, as it
may not be long enough to reach back to the ring.
3). Adjust the straps tightly so that the bag is secured.
Seat Standoff

7
2. Installing the system between the driver/passenger seat
(Refer to Figure 3)
Figure 3
1). Takeone strap and connect the latch to the upper metal ring on
the left side of the bag. Attach the “S” hook to the same ring
after looping the strap around the headrest of the driver’s seat.
Repeat this process for the right side (Passenger Seat).
2). Take another strap and connect the latch to lower metal ring on
the left side of the bag. Attach the “S” hook to the same ring
after looping the strap around the driver’s seat rail. Repeat this
process for the right side. In some vehicles, it may be neces-
sary to attach the “S” connector directly to the rail, as it may not
be long enough to reach back to the ring.
3). Adjust the straps tightly so that the bag is secured.

8
F. Controls, Indicators, and Connectors
1. Unit View (Refer to Figure 4)
Figure 4
1) Menu
2) UP Button
3) LEFT Button
4) DOWN Button
5) OK Button
6) RIGHT Button
7) Open Button
8) Previous Button
9) Stop Button
10) Next Button
11) Play Button
12) Pause
13) Screen Mode (WIDE) Button
14) Monitor Off Button
15) IR Transmitter
16) Remote Control Sensor
17) Power LED
18) DVD Video Output Jack
19) DVDAudio Output Jack
20)VideoInputJack
21)Audio L+R Input Jack
22) Power On/Off Switch
23) Volume +/- control
24) Headphone Jack 2
25) Headphone Jack 1
26) PAL/NTSC Switch
27) IR Switch
28) DC 9V Input Jack
29) Brightness +/- control

9
2. Remote Control View (Refer to Figure 5)
1) DISPLAY Button
2) ANGLE Button
3) SUBTITLE Button
4) AUDIO Button
5) ZOOM Button
6) UP/DOWN/LEFT/RIGHT/
ENTER Biotins
7) RETURN Button
8) A-B Button
9) FORWARD Button
10) REVERSE Button
11) SLOW Button
12) STOP Button
13) NUMERICKEYPAD
14) SETUP Button
15) MENU Button
16) REPEAT Button
17) PREVIOUS Button
18) NEXT Button
19) PLAY Button Figure5
20) PAUSE Button

10
G. Loading and Playing a Disc
a. After connecting power to the unit, slide the POWER ON/OFF on
the right side to ON, the DVD player’s POWER indicator lights.
b. Open the disc tray by pressing OPEN at the lower right of the disc
tray, and place a disc into the tray with the disc’s label facing up.
c. Press at the right side of the door until it clicks shut. The unit will
load the disc and start playing.
d.RotateBRIGHTand VOLUME to adjust theLCD’sbrightnessand
the DVD player’s volume.
e. To stop playing a disc, press STOP.
f. ToturnofftheDVDplayer,slidePOWERON/OFFtoOFF.The
DVDplayer’sPOWER indicatorturnsoff.
g. To remove the disc, open the disc tray, then you will see a
pictureontherightinnercornerofthe covertoindicatehowto
removethe disc,justuseyour fingertoaccess therightinner
corner of the disc tray and lift up the disc and remove it from
thedisctray. Pleaserefer to Figure6.
Figure 6

11
H. SETUP
Press ‘SETUP’ to display the Main screen o f the SETUP Menu on
the screen. Press ‘SETUP’ again to exit the SETUP Menu and the
unit will resume its last playback mode.
1) Press ‘SETUP’, the ‘General Setup’ page will display on screen.
General SETUP Menu Screen
a).Select ‘TV Type’ using UP/DOWN, and then press the RIGHT
buttontoenter thesubmenu. Choose TVTypeusingUP/DOWN
and then press ENTER to confirm the setting. Press the LEFT
button to return.
TV Type Screen Display
b).Select ‘TV DISPLAY’ using the DOWN button, and then press
RIGHT toenterthe submenu.SelecttheTV displaymodeonthe
screen using UP/DOWN, and press ENTER to confirm the
setting. Press LEFT to return.

12
TV DISPLAY Screen Display
* Normal/PS: When the player is connected to a normal TV, and
a wide picture is shown on the full screen.
* Normal/LB: When the player is connected to a normal TV, and
a wide picture is shown on the screen with a black strip at both
the top and bottom of the screen.
* Wide: When the player is connected to a wide screen TV, a
wide picture is shown on the full screen.
c).Select ‘ANGLE MARK’ using the DOWN buttton, and then press
theRIGHTbuttontoenter the submenu. Choose AngleMark on
or off using the UP/DOWN buttons and then press ENTER to
confirm the setting. Press the LEFT button to return.
ANGLE MARK Screen Display
* On: The screen will show the angle mark icon. (*If an angle
optionisavailable).
* Off: The screen will not display theAngle Mark icon.
NOTE: Not all discs contain above features.

13
d). Select ‘SCREEN SAVER’ using the DOWN button.
SCREEN SAVER Display
*On: enables screen saver
*Off: disables screen saver (off)
*NOTE: The DVD player will enter the Screen Saver mode after
approximately five minutes if the same image remains on the
screen.
e). Select “ Last Memory” by using the DOWN button.
LAST MEMORY Screen Display
*On: The unit will return to the last position on the disc.
*Off:: The unit will not return to the last position on the disc.
2) With no disc inside the player select “Video quality Setup” by using
the LEFT/RIGHT buttons, press “Enter” to enter the video quality
set up page.
Main SETUP Menu VIDEO QUALITY

14
a).Select “Brightness” by using the UP or DOWN buttons ,then
press Enter you can change the brightness by pressing the
LEFTor RIGHT buttons. To exit Brightness setting, press Enter
again to return the main Menu.
BRIGHTNESS Screen Display
b).Select “Contrast” by using the UP or DOWN buttons,then
press “Enter” you can adjust the Contrast by pressing the
LEFTorRIGHTbutttons.
CONTRAST Screen Display
To exit “Contrast” setting, press Enter again to return to the main
Menu.
c).Select “Hue” by using the UP or DOWN buttons, then press
“Enter” you can adjust the Hue by pressing the LEFT or RIGHT
buttons
HUE (Tint) Screen Display
To exit “Hue” setting, press “Enter”again to return the main Menu.

15
d).Select “Saturation “ by using the UP or DOWN buttons, then
press“Enter”you can adjusttheSaturationbypressingtheLEFT
orRIGHTbuttons.
SATURATION (Color)Screen Display
To exit “Saturation” setting, press “Enter” again to return to the
main Menu.
3).Select “Password” using the LEFT or RIGHT buttons,press Enter
to enter the password setup page,then press the RIGHT button to
enter the submenu.
PASSWORD CHANGE Menu
Press ‘Enter’ to enter the Password Change Page. Input the Old
Password or the Default Password, the New Password, and the
Confirmed New Password. Press ‘Enter’ to confirm the change.
PASSWORD CHANGE MENU

16
PASSWORD VERIFY Input Screen Display
NOTE: The Default Password is 3308. This password is
always effective even after you have selected your own
password and changed it. To avoid the possibility of others
using the defaultpassword toset theparentallevel and change
the password, you can record this default password in another
area and delete it from this manual. Some discs can be limited
depending on the age of users while some discs cannot.
4).Select ‘PREFERENCES’ using the LEFT or RIGHT buttons, then press
Entertoenterthe preferences page.
a. Select ‘Audio’ using the DOWN button, then press RIGHT to
enter the submenu. Select the audio language you desire using
the UP or DOWN buttons, then press ‘Enter’ to confirm the set-
ting. Press LEFT to return.
Preference Audio Language
b. Select ‘Subtitle’ the using DOWN button, then press RIGHT to
enterthesubmenu.Select the desired subtitle language or Sub-
title Off using the UP or DOWN buttons, then press Enter to
confirm the setting. Press LEFT to return.

17
Preference Subtitle Language
c.Select‘Disc Menu’ using theDOWNbutton,thenpress RIGHT to
enter the submenu. Select the Disc Menu Language you desire
using the UP or DOWN buttons , then press Enter to confirm the
setting. Press LEFT to return.
Preference Disc Menu LANGUAG
Note: Language and subtitle selection is only available for discs
that are recorded in the above listed languages. If the selected,
language is not available, the player will play and display on the
screen the original recorded language contained in the disc.
d. Select ‘Parental’ using the DOWN button, then press RIGHT to
enter the submenu.
Parental Preference Screen Display

18
Select the parental level you desire using the UP or DOWN but-
tonsfordiscswithlock-outfunctionormultipleratinglevels.These
are listed from the lowest level (1 Kid Safe) to the highest level
(Adult). Enter a 4 digit password, then press ‘ENTER’ to confirm
the parental level setting.
NOTE: The level of 8Adult is the factory default.
e. Select ‘Default’ using the DOWN button, then press RIGHT to
enter the submenu. Press Enter to make the setting return to the
factory-set mode.
Loading Factory Setting
NOTE: The parental setting is not affected by the default reset
function.

19
I. Playing DVD
1. Basic Operation
POWER
OPEN
PLAY
SLOW
PAUSE
STOP
NEXT
PREVIOUS
FORWARD
REVERSE
LEFT/RIGHT/UP/DOWN
ENTER
NUMBERS
RETURN
MENU
REPEAT
A-B
DISPLAY
ANGLE
SUBTITLE
AUDIO
ZOOM
SETUP
Turntheuniton/off
Remove/loadthedisc
StartPlay/Executeitemorsetting
Playat1/2,1/4,1/8or1/16 times speed
StillPicture
(1time)Stopatthepresentplayingpoint/
(2times)Stopplaying
Gotothenextchapter,trackorsceneduring
playback
Gobacktothepreviouschapter,trackor
sceneduringplayback
Scanforwardat2,4,8,16or32timesspeed
Scanbackwardat2,4,8,16or32timesspeed
UsedforMenuNavigation
Executeitemorconfirmsetting
Selectitemorsetting
Return
Displaythemainmenuofthedisc
Repeatplayingtitle,chapter,ortrack
RepeataspecificportionfrompointAtopoint
B of the disc
Displayinformation(title,chapter,track,time,
etc.).
Changetheviewinganglesonthescene
Selectthesubtitlelanguageandturniton/off
Selecttheaudiolanguage
Enlargeanimageto2,3,or4 times the
originalsize.
Display the setup menu to select and set
items,andexitthe setupmenu.

2. MENU
A DVDis dividedintosectionscalledtitlesandchapters. Whenyou
playaDVD,arootmenuofthediscwillappearonthescreenofyour
TVorMonitor.Thecontentsofthemenuvaryfromdisctodisc.Press
MENUduringplaybacktodisplaythemenu. SomeDVDsonlyallow
youtoselectdiscplaybackoptionsusing the DVD rootmenu.
3. DISPLAY (Display contents vary from disc to disc.)
1. PLAYING TIME AND REMAINING TIME
a.Duringplaybackpressthe ‘DISPLAY’ buttontodisplay the cur-
rent title number (1), the total number of Titles (2), the current
chapter number (3), the total Number of Chapters (4), and the
playing elapsedTimeforthetitle(5).Theheadingwilldisappear
automaticallyafter3secondsifnobuttonsarepressed.
Title, Chapter Number, and Time Screen Display
b.Press‘DISPLAY’againtodisplaytheremainingtimeof the title.
Theheadingwilldisappear automatically in 3seconds.
Title Remaining Time Screen Display
20