Aurora AS1018CD User manual

If the shredder continues to work after a shredding cycle and does not stop then this
is either;
1. The waste bin is full. You should empty the bin or compact the shredded paper.
2. Some paper is blocking the auto sensor, try clearing it by reversing and then
returning the switch to auto or by shredding some more paper.
3. Glue from envelopes or label’s is obstructing the sensor. You should not shred
gummed envelopes or sticky labels, try cleaning and lubricating the shredder with
Aurora SP1000 Lubrication and sharpening sheets.
Problem 3 –The shredder has jammed whilst shredding
Empty the waste bin and try reversing the unit to clear the jam.
If this does not work disconnect power, trim off paper above and below the jam,
reconnect power and try alternating between reverse and auto until the jam clears.
If at any point the shredder stops working during this process it has probably over
heated and will need to cool down for 60 minutes.
Please be careful not to exceed the maximum paper capacity and feed the paper in
straight, please be aware damage caused to the shredder by inserting too much
paper or by failing to shred using a straight paper path is classed as misuse and
invalidates your warranty.
Never attempt to clear paper jams by inserting implements into the shredder or by
opening the unit.
Warranty
Your Aurora shredder comes with a 12 months return to base warranty, please
contact your supplier for further details.
Aurora warrants all parts of the machine to be free from defects in materials and
workmanship for a period of 1 year from the date of the purchase by the original
consumer. If the shredder is found to be defective during the warranty period the
sole and exclusive remedy will be the repair or replacement at Aurora’s option and
expense.
Aurora Electronics (UK) Ltd disclaims any liability for incidental or consequential
damages attributable to the product. The liability of Aurora Electronics (UK) Ltd is
limited to the cost of the repair/replacement of the unit under warranty.
The warranty shall be immediately invalidated if unauthorized repairs or
modifications are made, if the machine has been abused or mishandled, if the
product has been re-sold, or if the product has not been operated in accordance
with the instructions contained in this document.
The warranty is in addition to and does not diminish the consumer’s statutory or
legal rights.
Aurora Electronics (UK) Ltd
Email: [email protected]
www.aurora-ltd.co.uk

User Manual for the AS1018CD Aurora Shredder
IMPORTANT!
READ ALL INSTRUCTIONS BEFORE USING
Thank you for purchasing the AS1018CD Paper Shredder. This product is designed to
shred paper and small staples it will also accept small paper clips, credit cards and
CD/DVD’s. It does not shred adhesive labels, self-seal envelopes, transparencies,
fabrics, glossy paper, newspaper, plastic (other than credit cards), cardboard or
continuous forms. Please note that using it for these purposes is likely to cause
damage and will invalidate your warranty. This paper shredder is not designed to shred
large volumes so please refer to the recommended usage capacity quoted below. You
may find paper particles in the bin when first opening the shredder this is a result of QC
testing procedures.
Recommended Daily Usage = 50 passes per day. (5 minutes on/ 20 minutes off)
Safety Instructions
1. Before use inspect the shredder, mains cable and plug for damage or defects.
2. Locate the shredder away from heat and water sources.
3. Ensure the switch is set to ‘off’ before connecting to the mains.
4. Always keep ties, loose clothing, jewelry and long hair away from the shredder.
5. Keep children and pets away from the shredder.
6. Disconnect from the mains when not in use or when emptying or cleaning.
7. Do not insert fingers or objects into the shredder at any time.
8. Never attempt to dismantle the shredder for any reason, please return to an
authorized service agent for repair or servicing.
9. Never dispose of flammable chemicals or materials that have come into contact with
flammable chemicals (for example nail polish, acetone and petroleum) in the shredder
basket. Never use flammable oils, petroleum based products or flammable aerosols of
any kind in the vicinity of the machine including compressed air dusters.
Operational Instructions
1. Remove all packaging and install the shredder unit on top of the waste bin ensuring it
locates firmly in position. There is a safety cut out on the shredder head to prevent
operation when not safely located on the waste bin, the shredder will not operate
unless placed correctly on the waste bin. The shredder will only operate with the
waste bin provided.
2. Set the switch to ‘Auto’, the shredder is now in stand–by mode.
3. The shredder will start automatically when paper is fed into the paper entry slot.
4. Ensure paper entry is straight so to avoid curling as it enters the shredder.
5. Do not enter more sheets of paper than stated on the shredder at one time. Sheet
capacity is based on a paper thickness of 75 gsm. Thicker paper will reduce the amount
of sheets the shredder can shred in one go as, will the presence of staples or
paperclips
6. Do not operate continuously for more than 5 minutes
7. Prolonged shredding will cause the unit to overheat and shut down. This is not a fault
and indicates the unit has reached its maximum temperature tolerance, turn the unit off
at the mains and allow it to cool down for 60 minutes before resuming normal operation.
8. If the amount of paper inserted is too much or is not fed in straight then the
shredding speed will slow or even stop. If this happens stop shredding and use the
reverse function to clear the jam. Always ensure the waste bin is not full before
reversing.
9. To shred a credit card –Insert the credit card in the entry slot on the shredder.
You should only shred one credit card at a time. To destroy a CD –Insert the CD
into the middle of the entry slot which is marked ‘Maximum 1 CD’, the CD will be
cross cut into several pieces. You should only destroy one CD at a time.
Status Indicators
1. If the overload LED comes on turn power off and leave the shredder for
approximately 60 minutes before continuing to use.
2. If the misaligned LED comes on ensure that the shredder head is fitted correctly
on the bin and the bin is not full.
Maintenance
1. Empty the waste bin frequently
2. Reversing the shredder often helps to clear a buildup of paper dust and particles,
always ensure the waste bin is not full before reversing.
FAQ & Troubleshooting
If you experience problems with your shredder please try some of the solutions
below, under no circumstance should you attempt to open the shredder unit, this will
expose you to a risk of electric shock and will invalidate your warranty.
Problem 1 –The shredder fails to operate
Is the shredder connected at the mains and is the power turned on?
Is the shredder switch set to ‘auto’?
Is the shredder located correctly on top of the basket? –(Press down firmly on the
shredder head to ensure it is in the correct position.)
Has the shredder over heated? –(Turn off at the mains and leave to cool down for
60 minutes then try again.)
Has the shredder blown a fuse? –(Turn off at the mains and try replacing the fuse in
the mains plug.)
Problem 2 –The shredder will not stop working
The shredder is designed to operate for a couple of seconds after paper has cleared
the machine –this is normal and helps clear paper through the cutting heads.
3. It is not essential to oil an Aurora
shredder however regular lubrication will
extend the life of your shredder, prevent
an increase in noise and help to keep
the shredder in optimum working
condition. We recommend using the
‘Aurora SP1000 Shredder Lubrication
and Sharpening sheets’ at least once
a month to keep your shredder blades
lubricated and free from a buildup of
paper dust. The Aurora SP1000 sheets
also contain a special grinding
powder that will keep your shredder
blades sharp. These are available from
your supplier in packs of 12.