Aurora AU870MA User manual

AU870MA
Model No.
Shredder User Manual
Please read these operating instructions before using the unit.
1-800-327-8508
USA Only
1-310-793-5650
International
Email: [email protected]
For more information, please visit us at:
www.auroracorp.com

WARNING:SAFETY INSTRUCTIONS, READ BEFORE USING!

3ENGLISH
WARNING:SAFETY INSTRUCTIONS, READ BEFORE USING!
Read instructions before use.
Avoid touching the document
feed opening with hands.
Product is not intended for use by
children (product is not a toy).
Do not insert foreign objects into
the paper entry slot.
Do not spray or keep any
aerosol products in or around the
shredder.
Keep loose clothing or jewelry
away from the paper entry slot.
Avoid getting hair near the
paper entry slot.
•AlwaysturntheshredderoffandunplugthepowercordfromtheACoutletwhen
notinuse,beforecleaningit,movingit,oremptyingthewastebasket.
•RISKOFFIRE-Seriousinjury,lossordamagemayoccur. Never use any petroleum based
or flammable oils, spray can oil or lubricants, or any aerosol products in or around the machine as
some oils can combust causing serious injury.
•NEVER dispose of flammable chemicals or materials that have come into contact with flammable
chemicals (for example, nail polish, acetone and gasoline) in the shredder basket.
•Nevershredlargepaperclips,windoworinsulatedenvelopes,continuousforms,
newsprint,boundpages(inexample:notepads,checkbooks,magazines,etc...),
transparencies,laminateddocuments,cardboard,anyitemswithadhesives,hard
materialsorplastic(exceptCreditCards).
•A socket-outlet should be near the equipment and be easily accessible.
•Never let the wastebasket become full. This will lead to shredded material being pulled back up into
the shredder and cause jams.
•Never place the shredder near water or any heat source.
•Do not use the shredder if the power cord is damaged in any way.
•Do not attempt to service this product yourself as doing so may expose you to sharp cutting blades
and/or electricity and will void the manufacturer's warranty.
•Never try to clean or clear the shredder blade.
•Never shred beyond the specified sheet capacity. This may result in extensive damage to the machine.

4ENGLISH
INSTALLATION
PaperShredder
OperatingInstructions
Installation
Operation
Maintenance
Troubleshooting
Service Center
Limited Warranty
*ONEFOLDEDSHEETOFPAPEREQUATESTO2SHEETSOFPAPER
Heavier paper, humidity or other than rated voltage may reduce shredding capacity.
Sheet Capacity
Paper Shred Size
Paper Entry Width
Credit Card
Duty Cycle
Voltage
8 Sheets of 20 lb. bond paper*
5/32 in. x 15/32 in. pieces
0.4 cm x 1.2 cm pieces
8.7 in / 220 mm
1 at a time
5 min. on / 30 min. off
120V~60Hz / 3.0 A
1. This model includes a built-in safety interlock mechanism, which requires the shredder to be correctly
mounted on to the included wastebasket. (FIGURE 1) THE SHREDDER WILL NOT OPERATE UNLESS
IT IS PROPERLY MOUNTED AS PICTURED.
2. A socket-outlet should be near the equipment and be easily accessible.
3. Connect the power cord to any standard 120 volt AC outlet.
Microcut shredders have very sharp exposed blades on the underside.
Use care when mounting the shredder on the wastebasket.
!Caution:
FIGURE1

5ENGLISH
OPERATION
ControlSwitch
Using the switch located on the unit, select one of the following settings
by sliding the switch either left or right. (FIGURE 2)
IAUTO:
This setting allows the shredder to be automatically started by inserting paper into the feed slot. Al-
ways feed the paper in as straight as possible. When the paper has passed through, the shredder
will automatically stop.
OOFF:
This setting turns off all features of the shredder. For safety reasons, we recommend that you leave
the shredder in the “Off” position whenever the shredder is unattended or not in use.
RREV(REVERSE):
In the unlikely event of a paper jam, the reverse setting can be used to help clear the cutters of
paper that did not pass through. Never attempt to clear a jam by using the reverse function until
you have emptied the wastebasket.
FIGURE2
CONTINUED NEXT PAGE



6ENGLISH
OPERATION
NOTE:
•Always turn off and unplug the shredder when not in use.
•This shredder will shred staples and small paper clips. It is recommended that you remove paper
clips whenever possible to extend the lifespan of your shredder.
•Only shred credit cards by feeding them vertically into the middle of the entry, releasing when shredding
begins. Never feed more than one credit card at a time.
•Overfeeding the shredder: Shredding beyond the specified sheet capacity can result in extensive
damage to the shredder. Overfeeding will strain the machine and quickly wear and break the cutting
blades and internal components.
•Overheating with extended use: In the event that the shredder has shred continuously beyond the
maximum running time and overheating, the unit will automatically shut off. If this happens, switch
the shredder Off for 30 minutes or longer before resuming normal operation.
Paper/CreditCardEntry:
Make sure you do not exceed sheet
count per pass (8 sheets max).
Insert paper as straight as pos-
sible into feed slot and release.
Insert one credit card at a time into
the middle of the feed slot.
Overheat:
Red light – Shredder has shred continuously beyond the maximum shred time and
needs to cool down before operation can restart. If this happens, switch the shred-
der off for 30 minutes or longer before resuming normal operation.
LEDStatusIndicator:

7ENGLISH
MAINTENANCE
Warning:Failuretoproperlymaintainyourshredderwillvoidthewarranty.
Oil the shredder blades every month with basic vegetable, cooking oil or shredder oil. Follow oiling
procedure below (FIGURE 3). It helps to keep the shredder blades operating well over many years of
use.
Oilingprocedure:
1. Turn off shredder.
2. Apply shredder oil across paper entry.
3. Turn shredder in reverse mode for 3~5 seconds.
Note:lubricatingoilisNOTincluded.
• Donotsprayorkeepanyaerosolproducts
inoraroundshredder.
• DONOTUSECANNEDAIRONSHREDDER.
CLEANING:
• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!
• Only clean the shredder by carefully wiping the unit with a dry soft cloth or towel.
• Do not clean or immerse shredder in water. Having the unit wet may result in damage or malfunction to
the electrical components. If the shredder happens to get wet, be sure to completely dry the unit immedi-
ately with a cloth or towel.
• Never use anything flammable to clean the shredder. This may result in serious injury or damage to the product.
FIGURE3
Shredder
Oil
DONOTUSE
AEROSOLPRODUCTS!
!Caution:

8ENGLISH
TROUBLESHOOTING
CONTINUED NEXT PAGE
If there is a problem with your shredder, check below for the symptoms and steps to resolve. If you con-
tinue to have problems, contact customer support at our Service Center 1-800-327-8508. DO NOT
ATTEMPT TO REPAIR BY OPENING THE SHREDDER HEAD. This will completely void the product
warranty.
Theshredderdoesnotworkatall.
1)Make sure the unit is pluggedin and that the outlet is in good working order.
2) Overheatingwithextendeduse: In the event that the shredder has shred continuously
beyond the maximum running time and overheated, the unit will automatically shut off. If this hap-
pens, switchtheshredderOfffor30minutes or longer before resuming normal operation.
3) If using a plastic bag to line the wastebasket, please remove it. This may cause the shredder not to
operate properly.
4) The activation sensor of the shredder is located near the center of the feed slot. Be sure to feed
directly into the center area to activate the machine (especially applies to smaller pieces of paper
or credit cards).
Theshredderrunsin“Rev(Reverse)”modebutnotin“Auto(On)”mode.
While in “Auto” mode, the motor will not start running until paper is inserted into the feed slot. Set the
unit to “Auto” and insert paper to shred. The sensor that activates the shredder in Auto mode is located
directly in the center of the slot. If the paper you are inserting is narrow, it may not be activating the
optical sensor. It is also possible that the feed slot has become blocked with paper. Insert an index card
or any rigid sheet of cardstock (old greeting card or folded file folder), directly in the center of the feed
slot, while applying force to help push the jammed paper through. This will usually clear any paper
blockage.
Howtoclearapaperjamintheshredder.
1) Switch the shredder over into Reverse (REV) mode. While in Reverse, the shredder will back up and
loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively
clear the machine. When jammed paper is loosened or removed, switch back to the Auto-On mode
to continue shredding. Repeat steps if needed.
2) With stubborn situations where the reverse function does not help, you may loosen the jammed
paper with shredder oil (cooking oil is acceptable, nothing aerosol). Start by drizzling oil into the
feed slot where the paper is jammed. Let it soak for about 30 minutes to completely saturate. Return
the shredder back to Auto-Onmode. Ifrequired,anindexcardorarigidsheetof
cardstock(oldgreetingcardorfoldedfilefolder)canbefedintotheshredderto
helppushthejammedpaperthrough.

9ENGLISH
TROUBLESHOOTING
Theshredderisconstantlyrunningwhilein“Auto(On)”mode.
1) It is possible that the activation sensor, which starts the shredder, has become blocked with paper.
Insert an index card or any rigid sheet of cardstock (old greeting card or folded file folder), directly
in the center of the feed slot, while applying force to help push the jammed paper through. This will
usually clear any paper blocking the activation sensor and feed entry.
2) The activation sensor is being triggered by dust, debris, or oil. A cotton swab may be
used to clean the sensor. DO NOT USE CANNED AIR. The activation sensor of the shredder is
located around the center of the feed entry.
Powerswitchinautoposition
Usethickpaperstockorgreetingcard
topushthejamthrough
If you have any questions in regards to the operation of this shredder or in need of a spare part, please
contact our service center at:
Telephone: [phone](U.S.A.only)or1-310-793-5650(International)
Business hours: Monday to Friday 8:00 am - 5:00 pm PST (Pacific Standard Time)
Email: [email protected]
Or for more information, please visit our website at http://www.auroracorp.com
SERVICECENTER

10 ENGLISH
LIMITEDPRODUCTWARRANTY
We warrant the cutting cylinders of the machine against defects of workmanship and material for a
period of 5years from the original purchase date to the original consumer, and all other parts of
the machine against defects of workmanship and material for a period of 1year from the original
purchase date to the original consumer.
Should there be a defect or malfunction of this product, we will repair or replace the product free of
charge. Customer is responsible for all shipping charges to return the defective product to us. Acopy
oftheproofofpurchaseshowingoriginalpurchasedateisrequired. This warranty is
void if the product has been subject to damage, unreasonable use, improper service, or other causes
not arising from defects in original material or workmanship. This warranty is void if factory seal is bro-
ken or removed from the product. This warranty does not include adjustments, parts or repairs required
by circumstances beyond the control of us.
There are no expressed warranties other than those stated herein.
Any expressed or implied warranties, including but not limited to merchantability and fitness for a
particular purpose are limited to the above warranty period. We shall not be liable for any incidental
or consequential cost, expenses or damages resulting from any failure defect or malfunction of this
product.
Some states do not allow the exclusion of limitations of implied warranties or consequintial damages,
therefore, the above limitations may not apply to you.
This warranty grants you specific legal rights, and you may also have other rights that vary from state to state.
Beforereturninganyproduct,pleasecallourServiceCenterforspecificreturn
instructions.
1-800-327-8508USAONLY
1-310-793-5650INTERNATIONAL
[email protected]