AutoConnect AC1379WR User manual

AC1379WR
8AM - 5PM Monday to Friday MT
CERTIFIED TRACKING SOLUTIONS
CALL TO TEST GPS TRACKING DEVICE BEFORE CLOSING UP THE DASH
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY DAMAGE EQUIPMENT AND VOID ITS WARRANTY
MUST BE TESTED!
1.855.287.4477
12-24V
AC1379WR
Green - Starter Disable Out (-)
Yellow: Input 1 (-) OPTIONAL
Vehicle Start
Interrupt Wire
CUT
Red
White
White - Key Ignition Source (+)
Red (12-24V+) - Constant
Black - GND
Black
Blue
RELAY
Type 1 GPS Only
Type 2 GPS with Starter Disable (optional)
Green - Starter Disable Out (-)
Yellow: Input 1 (-) OPTIONAL
White - Key Ignition Source (+)
Brown/Blue - DATA ONLY
DO NOT CONNECT
Red (12-24V+) - Constant
Fuse
Fuse
Black - GND
Brown/Blue - DATA ONLY
DO NOT CONNECT
1. Connect Red wire to Constant +12-24V and fuse.
2. Connect Black wire to Ground.
3. Connect White wire to True Ignition (+).
1. Connect Red wire to Constant +12-24V and fuse.
2. Connect Black wire to Ground.
3. Connect White wire to True Ignition (+).
4. Connect Green wire to relay.
87A
30
86
85
86 87a 87
85 30
REV072219
QUICK INSTALL GUIDE
AC1379WR
AC1379WR
AC1379WR

Securely position the device with the correct side pointing skyward. (device
label indicates proper orientation)
Do not cover with metal or position near any source of interference.
Failure to follow these instructions may result in weak cellular and/or GPS
signal and will impact the performance of the device.
Select in-vehicle device location
This device is equipped with an IP66 dust and water resistant case making it
suitable for a wide range of applications.
1
Connect constant power
The device requires a minimum 12V constant (Battery Power) on this
line to function
3
Connect ground
For best results, create a new connection to bare-metal chassis ground
4
Connect ignition
In order to function properly the device needs to be connected to a
suitable "True" Ignition source
2
Do not remove/bypass the fuse.
Connect the Red wire to a constant 12-24V source.
Do not use a shared ground or supplied ground from any module or device.
Connect the Black wire to ground.
This source has battery voltage whenever the vehicle is turned on and zero
volts whenever the vehicle is turned off.
This source does NOT drop in voltage during crank.
Connect the White wire to the ignition source.
This source must operate the same when starting by key or by
remote starter.
If connecting starter disable, the ignition source must provide sufficient
power to trigger the relay.
AC1379WR
a) Push and hold button for 3 seconds then release the button.
b) LED will come on after 10 seconds
IMPORTANT!
The device is delivered in “Shipment Mode.” To take the device out of
“Shipment Mode,” you must perform the following steps:
This is a wire that if cut will prohibit the vehicle from starting by any method.
Be sure to test after the wire is cut that the vehicle cannot be started AND
when reconnected the vehicle starts without fault codes.
Due to data bus systems on newer vehicles this wire may not be at the
ignition switch.
Connect the Red wire of the Relay Harness (87a) to one side of the cut Vehicle
Start Interrupt Wire.
Connect the Blue wire of the Relay Harness (30) to the other side of the cut
Vehicle Start Interrupt Wire.
Connect the relay to the vehicle start interrupt wire
(DO NOT USE A WIRE THAT WILL SHUT DOWN THE VEHICLE WHEN RUNNING)
Ensure Red wire of the device has constant 12-24 volts.
Ensure White wire is a TRUE ignition source. Measure with a multi-meter to
ensure voltage does NOT drop out during crank. Should have zero volts when
vehicle is not running.
Confirm Starter Kill connections. Remove relay from the relay harness. The
vehicle should not start by key or by remote starter.
Test connections
6
TEST DEVICE
Call the Toll Free number BEFORE CLOSING THE DASH
7
Connect the Black wire from Relay Harness (86) to the Green wire of the device.
Connect the White wire from Relay Harness (85) to the White wire of the device.
Connect starter disable
The device prevents the vehicle from starting by triggering a relay to open
and disconnect a "Vehicle Start Interrupt Wire". Starter disable is optional,
please check with your supervisor before proceeding.
Connect the device to the relay:
5