AutoTest Brake Fluid Tester User manual

User Manual
Version 1
AUTO Test
®
Brake Fluid Tester

DECLARATION OF CONFORMITY
We, AutoTest Products Pty Ltd. declare under our sole responsibility that the product AutoTest Brake Fluid Tester is in conformity with the provisions
of the following Council Directive: 1999/5/EC.
A copy of the Declaration of Conformity is available from http://www.autotest.net.au
© AutoTest Products Pty Ltd (AutoTest) [2020].
Copyright in the drawings, information and data recorded in this document (the information) is the property of AutoTest Products. This document and
the information are solely for the use of the authorised recipient and this document may not be used, copied, or reproduced in whole or part for any
purpose other than that for which it was supplied by AutoTest Products. AutoTest Products makes no representation, undertakes no duty, and accepts
no responsibility to any third party who may use or rely upon this document or the information.
Under no circumstances shall AutoTest Products be responsible for any loss of data or income or any special, incidental, consequential or direct
damages howsoever caused. The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind,
either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation
to the accuracy, reliability or contents of this document. AutoTest Products reserves the right to revise this document or withdraw it at any time without
prior notice.
E7474

Preface
Thank you for purchasing AutoTest products. Please read this manual completely before installing
and operating the product so as to ensure correct operation of the product. Make certain that this
manual can be accessed whenever necessary.
For Your Safety
Read these simple guidelines. Not following them may be dangerous. Read the complete user
guide. Further detailed information is given in this manual.
SWITCH ON SAFELY
Do not switch the device on when wireless device use is prohibited or when it may cause
interference or danger.
SWITCH OFF WHEN REFUELING
Do not use the device at a refuelling point. Do not use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the device where blasting is in progress.
USE SENSIBLY
Use only in the positions as explained in the product documentation.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ACCESSORIES AND BATTERIES
Use only approved accessories and batteries. Do not connect incompatible products.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user's guide for detailed safety
instructions. Do not connect incompatible products.
RISK OF DAMAGE TO EYES
Wear safety goggles when operating near vehicle battery as Battery acid, fumes, oil and
dust particles might cause damage to the eyes.

AutoTestTM Brake Fluid Tester
Brake Fluid Moisture Testing
Brake fluid is designed to have a high boiling point to withstand the high temperatures generated by friction in the
vehicle brake system. Unfortunately brake fluid readily absorbs moisture from air that transfers through the flexible
rubber hoses. Moisture reduces its boiling point leading to possible brake failure.
Overseas studies have highlighted that over 50% of vehicles on the road today may have fluid that is too old to be
within safety standards. Just like oil, brake fluid wears out and then it is simply not as reliable as fresh new brake fluid.
In addition, moisture contaminated brake fluid can corrode internal engine parts.
The AutoTest™ Brake Fluid Tester measures the moisture content in vehicle brake fluid. It provides accurate results in
less than one minute that allows users to identify vehicles that require a brake fluid change. Consequently, it increases
sales of brake fluid and brake fluid flushes.
The Brake Fluid Tester also increases the value of quick lube inspections, seasonal brake checks and routine
servicing.
Enhance your reputation for customer care and protect your clients by providing a brake fluid safety check.
It’s not age and mileage that determines brake fluid change intervals; it’s moisture absorption. Brake fluid gradually
absorbs moisture from the air. Moisture enters through the flexible hoses and reservoir breather. Absorbed moisture
reduces the boiling point of brake fluid. Under
prolonged hard braking conditions, particularly in hot weather or when a vehicle is heavily loaded, heat from the
braking action can suddenly
vaporize the fluid. Vapor unlike liquid is compressible and the driver’s foot suddenly goes straight to the floor resulting
in complete loss of
brakes, known as Vapor Lock.
The AutoTest™ Brake Fluid Tester is inserted into the master cylinder reservoir on the car and clipped onto the
battery. When the
button is pressed, a small sample of the fluid is heated up to boiling point where the temperature is recorded by an
accurate electronic
thermometer and displayed. This display alternates with the specified minimum boiling points so that it is instantly
clear if the fluid needs to be changed or is within specification. The meter can be withdrawn and the display will
continue so that it can be shown to the car owner.
Disconnecting the battery then resets the meter for use again. There is no additional cost of consumables, nothing to
order and stock and the
meter is practically maintenance free.
The test itself can be completed in less than one minute and it can then lead to a complete overhaul of the braking
system where appropriate. Customers appreciate work that may have a direct impact on their safety and that of their
family.
Unique Features
•Ergonomic Design
•User Friendly
•Checks brake fluid condition in under 1 minute
•Operates off 12 volt supply – vehicles own battery
•LCD display screen instructions lead operator through the complete test sequence
•Increase brake servicing revenue
•Suitable for use on new brake fluid and racing fluids
Product dimensions: 2250mm (h) x 1000mm (w) x 806mm (d)

WARRANTY
To ensure prompt warranty service should it be required, please complete warranty
registration form, and return to AutoTest Products Pty Ltd within 10 days of purchase of the
product. AutoTest Products or an Authorised Service Centre warrants this product against
defects in material and workmanship for a period of 12 months from the original date of
purchase. This warranty applies only to products and components supplied by AutoTest
Products which can be identified by the trade name or logo affixed to them or by other
documents.
AutoTest Products does not warrant any products not supplied by AutoTest Products.
During the warranty period, AutoTest Products or an Authorised Service Centre will repair
(or at its option replace), any defective component(s) without charge for labour, provided
the product is returned in its original or suitable equivalent container, freight prepaid, to an
authorised AutoTest Service Centre. Transit insurance and return freight will be at the
owner's expense.
In order to obtain calibration, warranty or non-warranty service, ship the product, freight
and insurance prepaid to your nearest AutoTest Service Centre. Attach to the product your
name, address, contact numbers, description of the problem and if a warranty claim, proof
of purchase (dated sales receipt or invoice). `
AutoTest Products or an Authorised AutoTestService Centre reserves the right to refuse
warranty repair if accident, abuse, misuse or misapplication has damaged the product in
transit or as a result of service or modifications by other than an Authorised Service
Centre, nor are any other warranties expressed or implied, including any regarding
merchantability or fitness for any other particular purpose. AutoTest Products or an
Authorised Service Centre is not responsible for incidental or consequential damages
resulting from the breach of any express or implied warranty, including damage to property
and, to the extent permitted by law, damages for personal injury.

Copyright 2020 AutoTest Products Pty Ltd ABN 47 005 712 005.
®denotes a trademark owned by AutoTest Products Pty Ltd ABN 47 005 712 005.
AUTO
TEST Products Pty Ltd
61-63 Parsons St Kensington VIC 3031 Australia
Phone: [phone]
Service: ([phone] [e-mail]
Sales:([phone] [e-mail]
www.autotest.net.au