Autronica Autro Safe System manual

116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire And Security AS
Installation Handbook
AutroSafe Interactive Fire Detection System
Release 4

COPYRIGHT ©
This publication, or parts thereof, may not
be reproduced in any form, by any method,
for any purpose.
Autronica Fire and Security AS and its
subsidiaries assume no responsibility for
any errors that may appear in the
publication, or for damages arising from
the information in it. No information in this
publication should be regarded as a
warranty made by Autronica Fire and
Security AS. The information in this
publication may be updated without
notice.
Product names mentioned in this
publication may be trademarks. They are
used only for identification.
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, 116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security
E-1676
This product contains static-sensitive devices. Avoid any electrostatic discharge.
The WEEE Directive
When the marking below is shown on the
product and/or its literature, it means that
the product should not be disposed with
other household wastes at the end of its
life cycle. During waste treatment,
disposal and collection, please separate
the product from other types of wastes
and recycle it responsibly to promote the
sustainable reuse of material resources.
This product should not be mixed with
other commercial wastes for disposal.

Introduction
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 3
Table of Contents
1. Introduction......................................................................7
1.1 About the Handbook..........................................................................7
1.2 Hardware / Software..........................................................................7
1.3 The Reader .......................................................................................7
1.4 Reference Documentation.................................................................8
2. Safety................................................................................9
2.1 Important Safety Information.............................................................9
2.2 National Standards and Regulations.................................................10
2.3 Technical Documentation..................................................................10
2.4 Recommendations for latest available Firmware and Operating
System...............................................................................................10
2.5 System Design, Installation, Commissioning, Testing and
Validation...........................................................................................11
2.6 Modifications to the products ............................................................11
2.7 Safety Notices ...................................................................................12
2.8 Compliance with Standards and Directives.......................................12
2.8.1 Standards NFPA 70 and NFPA 72 .........................................12
2.9 Environment Compatibility.................................................................13
2.9.1 Recycling.................................................................................13
2.9.2 Disposal ..................................................................................13
3. Pre-installation.................................................................14
3.1 Location.............................................................................................14
3.2 Environmental Requirements............................................................14
3.3 Mounting Height / Space Requirement .............................................14
4. System Units –Overview ................................................15
4.1 Power Supplies .................................................................................17
5. Loop Panels –Overview..................................................18
6. Mounting Instructions .....................................................19
6.1 Introduction........................................................................................19
6.2 Mounting Fire Alarm Control Panel BS-420/Controller BC-420........20
6.3 Mounting the Operator Panel BS-430...............................................22
6.4 Mounting Repeater Panel BU-BV-420 ..............................................23
6.5 Mounting Loop Panels (BV-110 and BU-110)...................................25
6.6 Mounting Power Cabinet STX Range ...............................................26
6.7 Mounting Power Supply Unit BPS-410 .............................................27
6.8 Inserting Text Foils............................................................................28
6.9 Cable Inlets / Outlets.........................................................................29
6.10 Cut Out Dimensions for Flush Mounting in a Wall ............................30
6.10.1Repeater Panel BU-BV-420....................................................30
6.10.2Operator Panel BS-430...........................................................31

Introduction
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 4
7. Power Consumption........................................................32
7.1 Mains Power......................................................................................32
7.1.1 STX Power..............................................................................32
7.1.2 BPS-410..................................................................................32
7.2 System Units .....................................................................................32
7.3 Loop Units .........................................................................................32
7.4 Phoenix Ethernet Switches ...............................................................33
8. Cable Connection Overview............................................34
9. Connecting Internal Cables.............................................35
9.1 Overview –BS-420 / BC-420............................................................35
9.2 BS-420 / BC-420...............................................................................36
9.2.1 AL_Com+ Connection on Controller Board BSA-400.............36
9.2.2 AL_Com+ Connection on Communication Module BSL-310..36
9.2.3 Multifunction Serial Port Connection on Controller Board
BSA-400..................................................................................36
9.2.4 Multifunction Serial Port Connection on Terminal Block,
List L1......................................................................................37
9.2.5 Multifunction Serial Port Connection Overview –BSA-400....37
9.3 BC-440 ..............................................................................................38
9.4 Internal Earth Cabling........................................................................38
10.Connecting External Cables ...........................................39
10.1 Introduction........................................................................................39
10.2 Before Connecting Cables ................................................................39
10.3 Cyber Security...................................................................................39
10.4 Mains Wiring - Two-pole Disconnect Device.....................................39
10.4.1115/230VAC Voltage BPS-410...............................................40
10.5 AutroFieldBus Connections...............................................................40
10.5.1Connections to BS-420/BC-420 - Terminal Block (List 1).......40
10.5.2Connections to Connector J2, Power Board BSF-400 ...........41
10.5.3Example of the Interconnection of Several Power Cabinets ..41
10.6 Connection of Network Cables (AutroNet)........................................42
10.6.1AutroNet Redundant Star Topology........................................42
10.6.2AutroNet Single Star Topology ...............................................43
10.6.3AutroNet Ring Topology..........................................................44
10.6.4Connection to Controller Board BSA-400...............................45
10.6.5Common Earth Connections...................................................45
10.7 RS-485 Connections to Terminal Block, List L1 ...............................46
10.8 RS-422 Connections to Terminal Block, List L1 ...............................46
10.9 RS-232 Connections to Terminal Block, List L1 ...............................46
10.10 24V Power Connections....................................................................47
10.10.1 Connections to Controller Board BSA-400A........................47
10.10.2 Connections to Power Board BSF-400................................48
10.10.3 Power Connection Overview................................................49
10.11 Mains Power Connections.................................................................50
10.11.1 Power Cabinet STX..............................................................50
10.11.2 Power Supply BPS-410........................................................50

Introduction
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 5
11.Installing I/O Modules......................................................51
11.1 Introduction........................................................................................51
11.2 Front View of I/O Module...................................................................51
11.3 Mounting / Removing I/O Modules....................................................52
11.3.1General ...................................................................................52
11.3.2Mounting .................................................................................52
11.3.3Removing................................................................................53
11.3.4Before Connecting Cables......................................................53
11.4 Data Sheets - I/O Modules................................................................53
12.Dual Safety Installation ...................................................54
12.1 Dual Safety System Overview...........................................................54
12.2 Rules of Thumb.................................................................................54
12.2.1Example 1: Connections Using AL_Com+ only......................55
12.2.2Example 2: Connections using both AL_Com+ and
AutroFieldBus..........................................................................56
12.3 Connections Overview ......................................................................56
12.3.1Connections –AutroKeeper BN-180.......................................58
12.3.2Switch Settings –AutroKeeper BN-180..................................58
13.Cable Specifications........................................................59
14.Service and Maintenance................................................60
14.1 Introduction........................................................................................60
14.2 Monthly Maintenance ........................................................................60
14.3 Annual Service and Maintenance .....................................................61
14.4 Fuse Replacements ..........................................................................62
14.5 Battery Replacement and Maintenance............................................62
14.6 Testing...............................................................................................62
14.7 Safety Measures during Commissioning and Maintenance..............63
14.8 SIL2 Approved Systems....................................................................63
14.9 Contact Information Local Service Representative...........................63
15.Appendix A - Controller Board BSA_400A.....................64
15.1 Circuit Board Layout..........................................................................64
15.2 Location inside Fire Alarm Control Panel BS-420.............................65
15.3 Description ........................................................................................65
15.4 Internal LED Indicators......................................................................66
15.5 Power Input Connector J18 (screw terminal)....................................66
15.6 Two-stage Push Button Reset (S5)...................................................67
15.7 USB Ports (J10, J11).........................................................................67
15.8 Multifunction Serial Port Connector J3 - AutroFieldBus and Fault
Relay .................................................................................................68
15.9 AutroFieldBus Connections...............................................................69
15.9.114.9.1 Ribbon Cable Connector BSA-400 to Terminal
Block L1 ..................................................................................69
15.10 Multifunction Serial Port Dipswitch Settings –Switch S6..................70
15.11 CAN Bus Termination Dipswitch Settings - Switch S7......................70
15.12 RS-485 Connections.........................................................................71
15.12.1 Ribbon Cable Connector BSA-400 to Terminal Block L1 ....71
15.12.2 Switch Setting –Switch S6 and S1......................................71
15.13 RS-422 Connections.........................................................................72

Introduction
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 6
15.13.1 Ribbon Cable Connector BSA-400 to Terminal Block L1 ....72
15.13.2 Switch Setting –Switch S6 and S1......................................72
15.13.3 Schematic of port equivalent:...............................................72
15.14 RS-232 Connections.........................................................................73
15.14.1 Ribbon Cable Connector BSA-400 to Terminal Block L1 ....73
15.14.2 Switch Setting –Switch S6 and S1......................................73
15.15 Serial Debug Connector J21.............................................................73
15.16 AL_Com+ Connector J5....................................................................74
15.17 LCD Backlight Connector J17...........................................................74
15.18 Ethernet Ports (RJ-45 Connectors)...................................................75
15.18.1 Ethernet Straight Through Cable .........................................75
16.Appendix B –Power........................................................76
16.1 Power Unit BPS-410 .........................................................................76
16.2 Power Board BSF-400 ......................................................................76
16.3 Description ........................................................................................77
16.4 Power Block Diagram –Example......................................................77
16.5 Batteries ............................................................................................78
16.6 Power Unit BPS-410 .........................................................................78
16.7 Battery Charging ...............................................................................78
16.8 Button S2 –Start on S2 on Standby Source.....................................79
16.9 Configuration Settings.......................................................................80
16.10 Dipswitch table –S5 and S6 .............................................................81
16.11 Connector Description BPS-410 .......................................................82
16.13 Fault Relay Watchdog J26................................................................83
16.14 Battery Resistance Measurement.....................................................84
16.15 Electronic fuses.................................................................................84
16.15.1 Power outputs ......................................................................84
16.15.2 Battery Input.........................................................................84
16.16 Part of an AutroFieldBus Network.....................................................85
16.17 Power Unit BPS-410 as Standalone .................................................85
17.Appendix B - Fault messages Power Board
BSF_400.................................................................................86
18.Appendix C –BP_405 (Obsolete) ...................................88
18.1 Mounting Power Cabinet BP-405 (obsolete).....................................88
18.2 Power Cabinet and Power Units .......................................................91
18.2.1Power Cabinet BP-405 (OBSOLETE).....................................91
18.2.2Power Unit BPS-405 (OBSOLETE)........................................91

Introduction
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 7
1. Introduction
1.1 About the Handbook
This handbook is intended to provide all necessary information for the
installation of a standard AutroSafe Interactive Fire Detection System,
Release 4. It also gives detailed information on connections to
Autronica’s local area network (AutroNet) and guidelines for the
installation and addressing of loop units.
Information on the connection of detectors and other loop units to the
detection loop is found in a separate handbook.
The chapter «Service and Maintenance» outlines the recommended
monthly and annual service and maintenance procedures that should
be performed after the system has been commissioned.
1.2 Hardware / Software
Systems with SW version 4.10.0 and later can have a mixed
environment consisting of BSA-400A and BSA-400 based panels.
Appendix A provides details on BSA-400A Controller Board in respect
to circuit board layout, components, switches, connectors etc.
For more information about replacement of previous BSA-400
Controller Boards with BSA-400A Controller Boards, refer to separate
handbook.
1.3 The Reader
The handbook is intended to be used by Autronica Fire and Security
trained service and technical personnel who are responsible for the
installation of the AutroSafe Interactive Fire Detection System, Release
4.
All tasks described in the handbook are to be performed without
applying power to the system.
Power must not be applied before commissioning, refer to
Commissioning Handbook.
Note that this handbook deals with the mechanical and electrical
installation only. All tasks described in the handbook are to be
performed without applying power to the system. Power must not
be applied before commissioning, refer to Commissioning
Handbook.

Introduction
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 8
1.4 Reference Documentation
The table below shows an overview of the technical marketing
documentation for AutroSafe Interactive Fire Detection System,
Release 4.
Docu
Document Name
System Description
Installation Handbook
Commissioning Handbook
User Guide, Remote Access
Installer’s Guide
Operator’s Handbook
User Guide
Wall Chart
Menu Structure
Datasheet; Fire Alarm Control Panel BS-420
Datasheet; Operator Panel BS-430
Datasheet; Repeater Panel BU-BV-420
Datasheet; Fire Brigade Loop Panel BU-110
Datasheet; Information Loop Panel BV-110
Datasheet; Controller BC-420
Datasheet; Controller Unit Rack BC-440
Datasheet; Power Cabinet STX Range with power supply (2A, 5A, 10A
Datasheet; Power Cabinet BP-405 (obsolete)
Datasheet; Power Unit BPS-405 (obsolete)
Datasheet; Power Unit BPS-410
Datasheet; AutroKeeper BN-180
NOTE:
Autronica Fire and Security provides documentation in other languages
and will be continuously updated according to changes in the English
version.
All documents can be downloaded at
http://product.autronicafire.com/products/
For detailed technical information on Phoenix Ethernet Switches, refer
to Phoenix Contact web site at
http://select.phoenixcontact.com/phoenix/dwl/dwlfr1.jsp?lang=en
t Name Part number File name
ly.

Safety
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 9
2. Safety
2.1 Important Safety Information
IMPORTANT SAFETY INFORMATION. READ ENCLOSED WARNINGS AND
SAFETY INFORMATION.
THIS MANUAL CONTAINS PRODUCT SAFETY WARNINGS, WARRANTY
DISCLAIMERS, LIMITATIONS OF LIABILITY
PRODUCT WARNINGS
THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION BY,
AN EXPERIENCED PROFESSIONAL. AUTRONICA FIRE AND SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS
PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL FIRE
RELATED PRODUCTS.
A PROPERLY INSTALLED AND MAINTAINED PRODUCT/SYSTEM MAY
ONLY REDUCE THE RISK OF EVENTS SUCH AS FIRE, SMOKE; IT IS NOT
INSURANCE OR A GUARANTEE THAT SUCH EVENTS WILL NOT OCCUR,
THAT ADEQUATE WARNING OR PROTECTION WILL BE PROVIDED, OR
THAT THERE WILL BE NO DEATH, PERSONAL INJURY, AND/OR
PROPERTY DAMAGE AS A RESULT.
AUTRONICA FIRE AND SECURITY
BATTERY OPERATED SENSORS, DETECTORS AND PANEL ACCESSORIES
HAVE A LIMITED BATTERY LIFE. WHILE THESE PRODUCTS ARE
DESIGNED TO PROVIDE SOME WARNING OF IMMINENT BATTERY
DEPLETION THE ABILITY TO DELIVER SUCH WARNINGS IS LIMITED AND
SUCH WARNINGS MAY NOT BE PROVIDED IN ALL CIRCUMSTANCES.
PERIODIC TESTING OF THE SYSTEM IN ACCORANCE WITH THE
INSTRUCTIONS PROVIDED IN THE USER MANUAL IS THE ONLY WAY TO
ENSURE ALL SENSORS, DETECTORS AND PANEL ACCESSORIES ARE
FUNCTIONING PROPERLY.

Safety
asafeinstall_dgb, AutroSafe Interactive Fire Detection System, Release 4,
116-P-ASAFE-INSTALL/DGB, Doc-1004796-2, 2021-08-23, Autronica Fire and Security AS
Page 10
WARRANTY DISCLAIMERS
TO THE MAXIMUM EXTENT PERMITTED BY LAW, AUTRONICA FIRE AND
SECURITY HEREBY DISCLAIMS ALL WARRANTIES AND
REPRESENTATIONS, WHETHER EXPRESS, IMPLIED, STATUTORY OR
OTHERWISE INCLUDING (BUT NOT LIMITED TO) ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH
RESPECT TO ITS PRODUCTS AND RELATED SOFTWARE. AUTRONICA
FIRE AND SECURITY FURTHER DISCLAIMS ANY OTHER IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS.
AUTRONICA FIRE AND SECURITY MAKES NO REPRESENTATION,
WARRANTY, COVENANT OR PROMISE THAT ITS PRODUCTS AND/OR
RELATED SOFTWARE (I) WILL NOT BE HACKED, COMPROMISED
AND/OR CIRCUMVENTED; (II) WILL PREVENT, OR PROVIDE ADEQUATE
WARNING OR PROTECTION FROM, FIRE , SMOKE; OR (III) WILL WORK
PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS.
2.2 National Standards and Regulations
Products from Autronica Fire and Security are developed and manufactured in
compliance with international safety standards. Any additional national or
local safety standards that apply where the equipment is installed and
operated, must also be taken into account together with the safety
regulations in the product documentation.
2.3 Technical Documentation
Anyone installing, commissioning, using or maintaining Autronica Fire
and Security products must follow the instructions in this handbook
and other applicable handbooks or standards in order to ensure safe
operation of the products and services. It is their responsibility to
ensure that updated documentation is used. The most recent
electronic versions can be downloaded from the Autronica product
web http://product.autronicafire.com/products/
2.4 Recommendations for latest available Firmware
and Operating System
We strongly recommend to always make sure that the systems are
operated with the latest available firmware/operating system in order to
ensure optimal operation and performance at all times.n