Avalue Technology OFT-10W01 User manual

Part No. E2017OT21A2R
OFT-10W01
10.1" Open Frame Tablet
Quick Reference Guide
1st Ed –05 January 2016
Copyright Notice
Copyright 2016 Avalue Technology Inc., ALL RIGHTS RESERVED.

OFT-10W01
2 OFT-10W01 Quick Reference Guide
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTATLLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Caution
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also
to prevent interference to the nearby radio and television reception. It is essential that only
the supplied power cord by used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for

Quick Reference Guide
OFT-10W01 Quick Reference Guide
3
compliance could void the user’s authority to operate the equipment.
RF exposure caution:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. & This device and its antenna(s) must not be co-located or
conjunction with any other antenna or transmitter
RF exposure caution:
This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found
compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247
(b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of
this Wireless LAN device is far below the FCC radio frequency exposure limits.
Nevertheless, this device shall be used in such a manner that the potential for human
contact during normal operation is minimized.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

OFT-10W01
4 OFT-10W01 Quick Reference Guide
Content
1. Getting Started............................................................................................................5
1.1 Safety Precautions ................................................................................................5
1.2 Packing List...........................................................................................................5
1.3 System Specifications ...........................................................................................6
1.4 System Overview...................................................................................................8
1.4.1 Right View.................................................................................................................................... 8
1.4.2 Left View ...................................................................................................................................... 8
1.5 System Dimensions...............................................................................................9
1.5.1 Front and Rear side ..................................................................................................................... 9
1.5.2 Installing Extend Brackets.......................................................................................................... 10
1.5.3 Front and Rear side (With Extend Bracket)............................................................................... 11
1.6 Flush Mounting Concept......................................................................................12
1.7 Wall Mounting Concept........................................................................................13
2. Hardware Configuration...........................................................................................14
2.1 Architecture Overview—Block Diagram...............................................................15
2.2 BCX11 Overviews................................................................................................16
2.3 BCX11 Connector list...........................................................................................18
2.4 BCX11 Connectors settings.................................................................................20
2.4.1 Touch button board connector (JTB1) ........................................................................................ 20
2.4.2 General purpose I/O connector (JDIO1) ..................................................................................... 20
2.4.3 RS-232 connector (J232-1)......................................................................................................... 21
2.4.4 RS-485 connector (J485-1)......................................................................................................... 21
2.4.5 USB connector (JCAM1)............................................................................................................. 22
2.4.6 AMPLIFIER_L (JAMP_L) ............................................................................................................ 22
2.4.7 AMPLIFIER_R (JAMP_R)........................................................................................................... 23
2.4.8 A-MIC connector (JAMIC1)......................................................................................................... 23
2.4.9 I2C connector (JSEN1) ............................................................................................................... 24
2.5 Antenna Assembly and Cable Routing ................................................................25
2.6 Android Rotate Setting.........................................................................................30

Quick Reference Guide
OFT-10W01 Quick Reference Guide
5
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x OFT-10W01 Open Frame Tablet

OFT-10W01
6 OFT-10W01 Quick Reference Guide
1.3 System Specifications
Board Specification
Processor
Intel Atom Z3735F
System Memory
2GB DDR3L RAM
Storage
8GB or 32GB eMMC
RF
WIFI
WIFI 802.11 b/g/n/
System Specification
Internal I/O
MIO
1 x RS232 (TX/RX) / RS485 header
1 x 16 bit GPIO header
1 x USB header
1 x I2C header (Optional)
1 x eDP & Dual channel 24bit LVDS
1 x backlight control & power
2 x speaker header (1.2W stereo)
1 x A-MIC header
1 x Touch Button connector header
1 x DC input 4pin header
External I/O
USB
2 x USB 2.0
1 x micro USB Client (Android only)
LAN
1 x 10/100 Ethernet
Display
1 x HDMI
Audio
1 x Head phone jack
SD
1 x Micro SD slot
Power-in
1 x DC jack
Mechanical & Environmental
Power
Requirement
19V DC input
Optional 12V or 24V DC input
Power Type
DC Jack
DC input 4pin header
Optional POE 802.3AT (10” only)
Operating Temp.
0°C ~ 40°C
Storage Temp.
-20°C ~ 60°C
Operating
Humidity
0% ~ 90% Relative Humidity, Non-condensing

Quick Reference Guide
OFT-10W01 Quick Reference Guide
7
LCD Characters
Panel
Resolution
1280 x 800
Luminance
350
View Angle
(H+-/V+-)
85°/85°
Touch
Touch
PCAP
Surface
hardness
6H
Note: Specifications are subject to change without notice.

OFT-10W01
8 OFT-10W01 Quick Reference Guide
1.4 System Overview
1.4.1 Right View
1.4.2 Left View
Connectors
Label
Function
Note
HP
Audio line-out connector
HDMI
HDMI connector
USB
2 x USB 2.0 connector
DCIN
DC power-in connector
SD
Micro SD card slot
Micro USB
Micro USB connector
LAN
RJ-45 Ethernet

Quick Reference Guide
OFT-10W01 Quick Reference Guide
9
1.5 System Dimensions
1.5.1 Front and Rear side
(Unit: mm)

OFT-10W01
10 OFT-10W01 Quick Reference Guide
1.5.2 Installing Extend Brackets
Step1. Locate brackets on both sides, matching the holes on the monitor.
Step2. Insert and fasten 16 screws on each side of the monitor to secure Mounting brackets.