Avalue Technology RiTab-10T1 User manual

RiTab-10T1
10”Semi-Rugged Tablet
Quick Reference Guide
1st Ed –01 April 2016
Copyright Notice
Copyright 2016 Avalue Technology Inc., ALL RIGHTS RESERVED.

RiTab-10T1
2 RiTab-10T1 Quick Reference Guide
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment and it also complies with Part 15 of the FCC RF Rules. This equipment must
not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provide with antenna installation instructions and consider
removing the no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Caution!
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment should be installed and operated with a minimum distance of 0mm between
the radiator and your body.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference; and

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
3
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS
102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on
RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de
RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information
canadienne sur l'exposition et la conformité de rf.
"This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter. This equipment should be installed and operated with a minimum distance of
0mm between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune
autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une
distance minimum de 0mm entre le radiateur et votre corps."
Notice
This guide is designed for experienced users to setup the system within the shortest time.
For detailed information, please always refer to the electronic user's manual.
Copyright Notice
Copyright 2016 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.

RiTab-10T1
4 RiTab-10T1 Quick Reference Guide
Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Life Support Policy
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL
OF Avalue Technology Inc.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into body, or (b) support or sustain life and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to
perform can be reasonably expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
5
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

RiTab-10T1
6 RiTab-10T1 Quick Reference Guide
Content
1st Ed –01 April 2016.......................................................................................................1
1. Getting Started ........................................................................................................8
1.1 Safety Precautions....................................................................................................8
1.2 Packing List...............................................................................................................8
1.3 System Specifications...............................................................................................9
1.4 System Overview....................................................................................................11
1.4.1 Front View.............................................................................................................................. 11
1.4.2 Rear View.............................................................................................................................. 11
1.4.3 Right Side.............................................................................................................................. 12
1.4.4 Left Side................................................................................................................................. 12
1.4.5 Top View................................................................................................................................ 13
1.4.6 Bottom ................................................................................................................................... 13
1.4.7 I/O Interface........................................................................................................................... 13
1.4.8 LED Indicator......................................................................................................................... 14
1.5 System Dimensions ................................................................................................15
1.5.1 RiTab-10T1............................................................................................................................ 15
2. Hardware Configuration .......................................................................................16
2.1 Battery Removal/Change........................................................................................17
2.2 Inserting SIM Card..................................................................................................17
2.3 Inserting Micro SD Card..........................................................................................18
2.4 MSR (Optionsl)........................................................................................................18
2.5 SCR (Optional)........................................................................................................19
2.6 Barcode Scanner (Optional)....................................................................................19
2.6.1 Barcode Scanner Specifications............................................................................................ 19
2.6.2 Barcode Scanner Distance.................................................................................................... 20
2.6.3 Barcode Scanner Trigger ...................................................................................................... 20
2.7 NFC.........................................................................................................................21
3. Software.................................................................................................................22
3.1 Adjusting LCD Brightness .......................................................................................23
3.2 Adjusting Speaker Volume......................................................................................25
3.3 Battery Overview.....................................................................................................26
3.4 WiFi.........................................................................................................................27
3.5 Bluetooth.................................................................................................................28
4. Accessories...........................................................................................................29
4.1 Desktop Cradle .......................................................................................................30
4.2 4-Bay Battery Charging Station...............................................................................31

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
7
4.3 Handstrap ...............................................................................................................31
4.4 Mushroom Head Handle.........................................................................................33
4.5 Shoulder Strap........................................................................................................34

RiTab-10T1
8 RiTab-10T1 Quick Reference Guide
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x RiTab-10T1
1 x 19V Adapter
1 x Power Cord

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
9
1.3 System Specifications
System
Processor
Intel® ATOM™Z3735F 1.33GHz Processor
System Memory
Onboard 2GB DDR3L
Storage
Onboard 32GB eMMC, Optional 64GB
Operation System
Win 10 / Android 4.4
Display & Touchscreen
LCD Size
10.1"
Display Type
WXGA
Resolution
1280x800
Luminance
350 cd/m²
Touch Type
10 Points Projective Capacitive
Wireless Communication
WLAN
802.11 b/g/n
Bluetooth
Bluetooth 4.0 Dual mode
WWAN
Optional 3G(WCDMA/HSDPAHSUPA/HSPA+)
Ethernet Chipset
2 x Intel I211AT 10/100/1000 Base-Tx Gbe Compatible
Data Collection
Camera
5MP Rear Camera With Auto Focus
NFC
ISO/IEC 14443 A/B, 15693/18092
Support MIFARE and Felica Specifications
Barcode Scanner
Optional 2D Barcode Scanner
Smart Card Reader
Optional Smart Card Reader
MSR
Optional Magnetic Stripe Reader
System I/O
I/O Connectors
1 x Audio Jack
1 x USB 2.0 Type A
1 x micro SD
1 x DC Jack
1 x Micro HDMI Output
1 x Micro SIM Slot
System Control
Control Buttons
1 x Power Button
1 x G Sensor Lock Button
2 x Barcode Trigger
LED Indicator
1 x Power/Battery
In-Box Accessory
Accessory
+19V 40W Power Adaptor

RiTab-10T1
10 RiTab-10T1 Quick Reference Guide
Power Requirement
Power Connector
DC Jack
Power Requirement
+19V
Battery
Hot-Swappable 27.75W Li-Polymer Battery (3S1P)
Internal 3.7W Li-Polymer Battery (2S1P)
Battery Operating Time
8 Hours
Adaptor
Input: 100~240Vac/50~60 Hz
Output: 40W Adaptor (19VDC@2.1A)
65W Adaptor (19[email protected])
Mechanical & Environmental
Construction
Rubber + Plastic
Dimension
281.9mm x 201mm x 20.8mm
Weight
1Kg
Operating Temperature
0°C~40°C (32°F~104°F)
Storage Temperature
-10°C~60°C (14°F~140°F)
Operating humidity
0%~90% Relative Humidity, Non-Condensing
IP Rating
IP54
Vibration Test
MIL-STD-810G Method 514.6 Procedure 1
Shock Test
MIL-STD-810G Method 516.6 Procedure 1
Drop
4-Feet Drop on Concrete Floor,
MIL-STD-810G 516.5 Procedure VI
Certifications
Certification Information
CE, FCC Class B
Note: Specifications are subject to change without notice.

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
11
1.4 System Overview
1.4.1 Front View
1.4.2 Rear View
Camera
Barcode Scanner
Trigger
Barcode Scanner
Trigger
Battery Lock
Speaker
Accessory Hole
NFC Reader
SCR
MSR
Power Button
LED Indicator

RiTab-10T1
12 RiTab-10T1 Quick Reference Guide
1.4.3 Right Side
1.4.4 Left Side
Power Button Control Mode
Time
Function
1 Sec.
Power On
4 Sec.
ForcedPower Off
1 Sec.
Suspend
1 Sec.
Resume
7 Sec.
EC Reset
SCR
MSR
Power Button
G Sensor Lock

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
13
1.4.5 Top View
1.4.6 Bottom
1.4.7 I/O Interface
Connectors
Label
Function
Note
Micro HDMI
Micro HDMI Connector
Micro SD
Micro SD Card Slot
USB
1 x USB 2.0 Type A
Docking
Connector
Docking Station Connector
Audio
Audio Connector
DC-In
DC Power-In Connector
Barcode Scanner
I/O
(See 1.4.7)
I/O
(See 1.4.7)

RiTab-10T1
14 RiTab-10T1 Quick Reference Guide
1.4.8 LED Indicator
Status
Power Off
Sleep Mode
Power On (Main Battery
Capacity)
Not Charging
LED Off
LED Off
21% ~ 100% LED Off
11% ~ 20% Red, Blinking:
ON 0.5sec., OFF 2 sec.
4% ~ 10% Red,
Blinking: ON 0.5 sec., OFF 1
sec.
Charging
Amber
Amber
Amber
Charging Finished w A/C
Green
Green
Green
LED
Indicator

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
15
1.5 System Dimensions
1.5.1 RiTab-10T1
(Unit: mm)

RiTab-10T1
16 RiTab-10T1 Quick Reference Guide
2.Hardware
Configuration
Note: If you need more information, please visit our website:
http://www.avalue.com.tw

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
17
2.1 Battery Removal/Change
Rotate the battery lock to remove/change the battery.
2.2 Inserting SIM Card
SIM card slot is located inside the battery bay. Remove the battery before inserting the
SIM card in the direction shown as below.
NOTE: Cellular function is only available when 3G module is installed.

RiTab-10T1
18 RiTab-10T1 Quick Reference Guide
2.3 Inserting Micro SD Card
Push the Micro SD card into the slot. To remove the Micro SD card, simply push the card
again and it will pop out automatically..
2.4 MSR (Optionsl)
The Magnetic Strip Reader is located at the right side of RiTab-10T1 and is used in the
direction shown as below.

Quick Reference Guide
RiTab-10T1 Quick Reference Guide
19
2.5 SCR (Optional)
The Smart Card Reader is located at the right side of RiTab-10T1 and is used in the
direction shown as below.
2.6 Barcode Scanner (Optional)
2.6.1 Barcode Scanner Specifications
Performance
Sensor
CMOS sensor with rolling shutter and 640*480pixel resolution.
Illumination &
Aiming
White LED Illumination; Aimer: Red LED Dot
Typical Frame Rate
30 fps
Motion Tolerance
Up to 100 cm/s (4 in/s) for 13 mil UPC at optimal focus
Field of View
Horizontal Field Angle: 37.8°, Vertical Field Angle: 28.8°
Scan Angles
Tilt: 360°, Pitch: +/- 45°, Skew: +/-45°
Symbol Contrast
35% minimum reflectance
Symbologies
Aztec Code, Codabar, Codablock F, Code 11,Code 32(PARAF)
Code 128, Code 2 of 5, Code 39, Code 93, Data Matrix,
EAN/JAN-13, EAN/JAN 8, EAN-UCC Composite Codes,
EAN-UCC Emulation, IATA Code 2 of 5, Interleaved 2 of 5,
Matrix 2 of 5, MaxiCode, MicroPDF417, MSI, PDF417, QR Code,
GS1 DataBar, TCIF Linked Code 39, UPC-A, UPC E, RSS

RiTab-10T1
20 RiTab-10T1 Quick Reference Guide
Expanded , RSS Limited , RSS-14 , Chinese Sensible(Han Xin)
code , Codablock A , UPC-A/EAN-13 with Extended coupon
Code , Coupon GS1 , GS1codebar
Mechanical/Electrical
Dimensions
Typical: 21.17mm(W) x 14.6mm(D) x 11.52mm(H)
Maximum: 21.57mm(W) x 14.95mm(D) x 11.73mm(H)
Interface
12 pin non-zif connector
Input Voltage
232: 3.3VDC ± 5%, USB: 5.0VDC ± 5%,
Typical Current
Draw
232: 3.3V input--Scan 310mA RMS, Idle 65mARMS, Standby
3.5mA
USB: 5V input---Scan 220mA RMS, Idle 60mA RMS, Standby
2.5mA
2.6.2 Barcode Scanner Distance
2.6.3 Barcode Scanner Trigger
Press the barcode scanner trigger to active the function if your RiTab-10T1 has
built-in barcode scanner.
Trigger
Trigger