Avanti WD001 User manual

INSTRUCTION MANUAL
Model Number/Número de Modelo:
WD001
HOT AND COLD WATER DISPENSER
DISPENSADOR DE AGUA FRIA Y CALIENTE
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS.
La sección en español empieza en la página 11.
Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications
without notice.
Avanti Products
P.O. Box 520604 - Miami, Florida 33152
www.avantiproducts.com

2
Table of Contents
Help Us Help You
3
Parts and Features
4
Important Safety Instructions
5
Installation Instructions
5
Electrical Connection
6
Before Using Your Dispenser
7
Operating Your Water Dispenser
8
Control and Display Panel
8
Child Safety Guard on Hot Water Faucet
8
Care and Maintenance
9
Taking Dispenser Out of Service
9
Wiring Diagram
9
Problems with Your Dispenser
10
Troubleshooting Guide
10
Instrucciones en Español
11 –12

3
HELP US HELP YOU
Read this guide carefully.
It is intended to help you operate and maintain
your new water dispenser properly.
Keep it handy to answer your questions.
If you don't understand something or you need
more assistance please call:
Avanti Customer Service
800-220-5570
Keep proof of original purchase date (such as
your sales slip) with this guide to establish the
warranty period.
Write down the model and serial numbers.
You'll find them on a label located on the back
side of the unit.
Please write these numbers here:
____________________________________
Date of Purchase
____________________________________
Model Number
____________________________________
Serial Number
Use these numbers in any correspondence or
service calls concerning your water dispenser.
If you received a damaged water dispenser,
immediately contact the dealer (or builder) that
sold you the water dispenser.
Save time and money. Before you call for
service, check the Trouble Shooting Guide. It
lists causes of minor operating problems that
you can correct yourself.
IF YOU NEED SERVICE
We're proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, here are some
steps to follow for further assistance.
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased. In
most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the
details, including your telephone number, and
send it to:
Customer Service
Avanti Products
10880 NW 30 Street
Miami, FL 33172

4
PARTS AND FEATURES
1
Water Intake
5
Hot Water Outlet
2
Display Panel
6
Cold Water Outlet
3
Hot Water Faucet
(With Child Safety Guard)
7
Removable Drip Tray
4
Cold Water Faucet
Back
Panel
Hot and Cold Water System
Power Switches
Drain Plug

5
Important Safety Instructions
WARNING
To reduce the risk of fire, electrical shock,
or injury when using your appliance, follow
these basic precautions:
Read all instructions before using the water dispenser.
Never clean parts with flammable fluids. The fumes can create a fire hazard or
explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity
of this or any other water dispenser. The fumes can create a fire hazard or
explosion.
-Save these instructions-
INSTALLATION GUIDELINES:
Remove the exterior and interior packing.
Place your appliance on a countertop or surface that is strong enough to support the dispenser
when it is fully loaded. The unit is provided with four plastic feet, if it does not sit level on the floor,
adjust the front feet to level the unit well to the floor.
Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Extreme cold ambient temperatures may also cause the appliance not to perform
properly.
Allow 5 inches of space between the water dispenser and the wall, which allows for proper air
circulation to cool the compressor.
Plug the appliance into an exclusive properly installed-grounded wall outlet. Do not cut or remove
the third (ground) prong from the power cord under any circumstances. Any questions concerning
power and/or grounding should be directed toward a certified electrician or an authorized Avanti
Products service center.
This water dispenser is not recommended for outdoor use.
Do not locate the dispenser in area where the temperature may fall below freezing (32º F).
Keep area around dispenser free of dust and dirt.
Keep the reserve supply of water bottles away from excessive heat and light.
Never unplug the water cooler, except for maintenance.

6
ELECTRICAL CONNECTION
This appliance should be properly grounded for your safety. The power cord of this appliance
is equipped with a three-prong plug which mates with standard three prong wall outlets to
minimize the possibility of electrical shock.
Do not under any circumstances cut or remove the third ground prong from the power cord supplied.
For personal safety, this appliance must be properly grounded.
This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly
grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation
to have it replaced with a properly grounded 3-prong wall outlet.
The cord should be secured behind the appliance and not left exposed or dangling to prevent
accidental injury.
The appliance should always be plugged into its own individual electrical outlet which has a voltage
rating that matches the rating label on the appliance. This provides the best performance and also
prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never
unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from
the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
When moving the appliance, be careful not to damage the power cord.
EXTENSION CORD
Because of potential safety hazards under certain conditions, it is strongly recommended that you do
not use an extension cord with this appliance. However, if you must use an extension cord it is
absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord
having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at
least 10 amperes.
SURGE PROTECTOR
Most electrical appliances use a series of electric control boards to operate. These boards are very
susceptible to power surges and could be damaged or destroyed.
If the appliance is going to be used in an area or if your city / country is prone to power surges /
outages; it is suggested that you use a power surge protector for all electrical devices / appliances you
use. The surge protector that you select must have a surge block high enough to protect the
appliance it is connected to. If you have any questions regarding the type and size of surge protector
needed contact a licensed electrician in your area.
Damages due to power surges are not considered a manufacturer covered defect and will void your
product warranty.
Warning
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
damaged, have it replaced by an authorized Avanti Products service center.

7
OPERATION INSTRUCTIONS:
Before Using Your Water Dispenser
Check to be sure the following parts are included:
Instruction manual
2 extra cup dispenser cabinet plugs (Located in the bag with this manual)
2 extra drain seals (Located in the bag with this manual)
Accessories order form.
Before connecting the appliance to the power source, let it stand upright for approximately 2
hours. This will reduce the possibility of a malfunction in the cooling system from handling during
transportation.
The water dispenser is pre-cleaned at the factory but the reservoir and water lines must be flushed
with fresh water before use as follows:
Keep the unit unplugged.
Fill water tank with tap water full to capacity. Wait for 15 minutes as indicated above.
Slide child safety button then push the hot water faucet (See the Hot Water Faucet diagram on
the next page) until water comes out, then stop.
Plug the dispenser into the electrical outlet. Locate and flip the COLD (Green) and HOT (Red)
power switches at the rear of the unit to the ON position.
We are ready to complete the first cycle. In order to do that, wait for the hot water to reach
temperature in approximately 10 minutes, and then wait for the cold to reach temperature
(another 40 minutes, approximately).
Warning: The water coming out of the back may be scolding hot
Flip the COLD (Green) and HOT (Red) power switches to the OFF position.
Unplug the dispenser from the electrical outlet. Proceed to drain the water from the faucets one at
a time until no more water remains. (Note: To facilitate this operation, use a large container).
Then, drain any water left in the tanks by opening the drain plug located on the back, until it drains
completely.
Proceed to close the drain cap tightly and ensure there are no leaks.
Push water faucet buttons to insure water flows from both faucets.
Plug dispenser back into the electrical outlet.
Flip the COLD (Green) and HOT (Red) power switches to the ON position.
Now you are ready to use your water dispenser.
ATTENTION:
If you do not plan to use the water heating function for more than three days, we recommend that you
turn off the hot water function.

8
OPERATING YOUR WATER DISPENSER
Steps To Replace Water Bottles
Remove cap from the 5-gallon bottle and use a clean cloth to wipe off the neck of the bottle.
Carefully lift bottle (approx. 40 lbs.) using your legs and not your back. Do not place hands on
opening of bottle while placing in reservoir.
Place the 5-gallon bottle of water on the water intake, allow the water to stand for approximately 5
minutes.
Wipe off any water which may have splashed on dispenser top.
Control and Display Panel
For operation of unit, please fill water and make sure water settles inside the water tank, and then
switch on both hot and cold switches at back of unit.
To get hot water:
Slide red safety button to the right and hold
while pressing downward on hot water faucet
to dispense hot water.
Safety button will return to its original position
when faucet is released.
NOTE:
THE DISPENSING CAPACITY OF HOT WATER IS APPROXIMATELY 2 ½ CUPS AT A SINGLE
TIME. ONCE THE MAXIMUM NUMBER OF CUPS HAS BEEN DISPENSED THE RESERVOIR
WILL REFILL AND BE READY TO DISPENSE ANOTHER 2 ½ CUPS IN APPROXIMATELY 5 –6
MINUTES
NOTE:
THE HOT WATER FAUCET HAS A CHILD-SAFETY GUARD ATTACHMENT.
When a new bottle is installed you must open the hot water faucet and remove no less than 4 full cups of
water to insure the water flows properly and the water reservoir is at the proper level.

9
CARE AND MAINTENANCE
Wash the inside of the reservoir with a warm water and baking soda solution. The solution should
be about 2 tablespoons of baking soda to a quart of water. (Turn off the hot water function).
The drip tray and water faucets should be cleaned with mild detergent and warm water.
At regular intervals or once a month inspect the coils located across the back of the dispenser.
Vacuum accumulation of dust or clean it with a hard brush.
TAKING DISPENSER OUT OF SERVICE
If the water dispenser will not be used for a long period of time, unplug the power cord from the
wall outlet.
Turn off the hot water.
Drain the water through the faucets.
Drain the water from the tanks by removing the plug from the back of the dispenser.
Unit should NOT be transported on the units side. Place it upright if possible and cover it with a
blanket.
Cup Dispenser (OPTIONAL)
The cup dispenser may be installed by using the mounting holes (covered with plastic caps) located
near the top of the right side panel of the cooler. The cup dispenser comes equipped with a mounting
bracket and screws and may be ordered by completing the enclosed order form provided with your
instruction manual.
WIRING DIAGRAM
WARNING—THE WATER COMING OUT OF THE BACK MAY BE SCOLDING HOT.

10
PROBLEMS WITH YOUR WATER DISPENSER?
You can solve many common water dispenser problems easily, saving you the cost of a
possible service call. Try the suggestions outlined below to see if you can solve the problem
before calling the servicer.
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
Water dispenser does not operate.
Not plugged in.
The circuit breaker tripped or a blown fuse.
Water cooler is not cold enough.
Check to be sure the cold switch on the back is ON.
The water dispenser does not have the correct
clearances.
Cooling coils at the back of the unit need to be cleaned.
Water dispenser hot water is not hot enough.
Check to be sure the hot switch on the back is ON.
Thermostat may be tripped. Contact Customer Service
for additional instructions.
Compressor turns on and off frequently.
The room temperature is hotter than normal.
The water dispenser does not have the correct
clearances.
Vibrations.
Check to assure that the water dispenser is level.
The water dispenser seems to make too much
noise.
The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds
caused by the flow of refrigerant in your water dispenser.
Contraction and expansion of the inside walls may
cause popping and crackling noises.
The water dispenser is not level.
Bottle feels warm.
The water system is overfilled. Dispense Cold water until
air is released into the bottle.
Water bottle is hot.
Water is boiling in the hot tank and bubbling up into the
bottle. Press the hot dispenser button until water flows to
remove air from the hot tank.

11
INSTRUCCIONES EN ESPAÑOL
ADVERTENCIA
EL USO INCORRECTO DEL CABLE ATIERRA PUEDE OCASIONAR UN CHOQUE ELECTRICO.
SI EL CORDON ESTA DAÑADO, REEMPLACELO EN UN CENTRO DE SERVICIOS AUTORIZADO
POR AVANTI PRODUCTS.
PASOS RECOMENDADOS PARA CAMBIAR EL BOTELLON
DIRECCIONES BASICAS DE OPERACION:
COLOQUE EL ENFRIADOR DE PIE POR UN PERIODO DE 2 HORAS ANTES DE ENCHUFAR
LA UNIDAD A LA PARED.
COLOQUE EL ENFRIADOR EN UN AREA BIEN VENTILADA Y DEJE UN ESPACIO DE UN
POCO MAS DE 5 PULGADAS ENTRE LA UNIDAD Y LA PARED.
ESCOJA UN LUGAR CON PISO NIVELADO.
NO COLOQUE EL ENFRIADOR DONDE LA TEMPERATURA AMBIENTAL PUEDA BAJAR DE
32°F (0°C).
REMUEVA LA ARANDELA QUE ESTABILICE EL BOTELLON ESTANDAR, ESTE ARTICULO
NO ES NECESARIO CUANDO ESTE UTILIZANDO EL BOTELLON DE ZEROWATER.
ANTES DE ENCHUFARLO
AUNQUE EL ENFRIADOR SALE LIMPIO DE LA FABRICA, DEBE LIMPIAR Y ESTERILIZAR LOS
CONDUCTOS DEL TANQUE Y LOS GRIFOS DE ACUERDO A LOS SIGUIENTES PASOS:
LLENE EL TANQUE DE AGUA (HASTA EL TOPE) CON AGUA DE LA PILA.
DEJE NIVELAR EL AGUA POR 15 MINUTOS.
ENCHUFE LA UNIDAD A LA PARED.
ENCIENDA LOS INTERRUPTORES DE AGUA CALIENTE Y FRIA LOCALIZADOS EN LA
PARTE TRASERA DE LA UNIDAD.
VACIE EL TANQUE COMPLETAMENTE ABRIENDO LA TAPA DE DRENAJE SITUADA ATRAS
DEL GABINETE. CIERRELAS. AHORA SU DISPENSADOR DE AGUA ESTA LISTO PARA
USAR.
PARA OBTENER AGUA CALIENTE:
MUEVA EL BOTON DE SEGURIDAD HACIA LA DERECHA SIN SOLTARLO.
MANTENGA AGARRADO ESE BOTON DE SEGURIDAD MIENTRAS QUE EMPUJE EL GRIFO
HACIA ABAJO PARA DISPENSAR EL AGUA CALIENTE.
CUANDO SUELTE EL GRIFO ASEGURESE DE RETORNARLO A LA POSICION ORIGINAL.
NOTA: SU ENFRIADOR FUE LIMPIADO Y ESTIRILIZADO ANTES DE SALIR DE LA FABRICA. EN
CASO QUE SIENTA ALGUN SABOR EN EL AGUA, ECHE UNA CUCHARADA DE BICARBONATO
DE SODIO Y AÑADA AGUA DE LA PILA. LLENE EL TANQUE Y REPITA LA OPERACION INICIAL.
AVISO:
ESTE GRIFO DE AGUA CALIENTE TIENE UN ADAPTADOR DE SEGURIDAD PARA
NIÑOS.

12
MANTENIMIENTO
ANTES DE EFECTUAR LA LIMPIEZA, DESENCHUFE EL ENFRIADOR.
PARA LIMPIAR LAS PARTES DE PLASTICO SE REQUIERE JABON LIQUIDO YAGUATIBIA.
NO USE LIMPIADORESABRASIVOS EN LASUPERFICIE SUPERIOR NI EN LA BANDEJADE
ESCURRIMIENTO.
SI NO VAAUSAR EL ENFRIADOR POR UN TIEMPO PROLONGADO
DESENCHUFE LAUNIDAD.
QUITE EL BOTELLON DE AGUA.
COLOQUE LOS INTERRUPTORES (EN LA PARTE TRASERA) EN LA POSICION “OFF”.
(APAGADO)
DRENE ELAGUAABRIENDO LAS LLAVES.
DRENE LA APERTURA EN LA PARTE TRASERA QUITANDO EL TAPON (EN LA PARTE
TRASERA).
WD001 –06032014
PRINTED IN CHINA