Avaya S8510 User manual

Job Aids for Field Replacements (FRUs)
for the Avaya S8510 Server
03-602953
Issue 1
June 2008

© 2008 Avaya Inc.
All Rights Reserved.
Notice
While reasonable efforts were made to ensure that the information in this
document was complete and accurate at the time of printing, Avaya Inc.
can assume no liability for any errors. Changes and corrections to the
information in this document may be incorporated in future releases.
For full legal page information, please see the complete document,
Avaya Legal Page for Hardware Documentation, Document number
03-600759.
To locate this document on our website, simply go to http://
www.avaya.com/support and search for the document number in
the search box.
Documentation disclaimer
Avaya Inc. is not responsible for anymodifications, additions, or deletions
to the original published version of this documentation unless such
modifications, additions, or deletions were performed by Avaya.
Customer and/or End User agree to indemnify and hold harmless Avaya,
Avaya's agents, servants and employees against all claims, lawsuits,
demands and judgments arising out of, or in connection with, subsequent
modifications, additions or deletions to this documentation to the extent
made by the Customer or End User.
Link disclaimer
Avaya Inc. is not responsible for the contents or reliability of any linked
Web sites referenced elsewhere within this documentation, and Avaya
does not necessarily endorse the products, services, or information
described or offered within them. We cannot guarantee that these links
will work all of the time and we have no control over the availability of the
linked pages.
Warranty
Avaya Inc. provides a limited warranty on this product. Refer to your
sales agreement to establish the terms of the limited warranty. In
addition, Avaya’s standard warranty language, as well as information
regarding support for this product, while under warranty, is available
through the following Web site:
http://www.avaya.com/support
Copyright
Except where expressly stated otherwise, the Product is protected by
copyright and other laws respecting proprietary rights. Unauthorized
reproduction, transfer, and or use can be a criminal, as well as a civil,
offense under the applicable law.
Avaya support
Avaya provides a telephone number for you to use to report problems or
to ask questions about your product. The support telephone number
is 1-800-242-2121 in the United States. For additional support telephone
numbers, see the Avaya Web site:
http://www.avaya.com/support

03-602953 Issue 1 June 2008 3
Job Aid: Replacing the Avaya S8510 server. . . . . . . . . . . . . . . . 7
Reusing hardware components . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Replacement materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hardware and tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Required information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Before going to the customer site . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Replacing the S8510 server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Back up data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power down the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Label and disconnect cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remove the S8510 server from the rack . . . . . . . . . . . . . . . . . . . . . 12
If you are re-using the SAMP/dual NIC . . . . . . . . . . . . . . . . . . . . . . 14
Replace the server cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Install the replacement S8510 server in the rack . . . . . . . . . . . . . . . . 20
Install Communication Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Set TELNET parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Install the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Verify the software version . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Set the time, date, and time zone . . . . . . . . . . . . . . . . . . . . . . . . . 22
Copy files to the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Download optional language files . . . . . . . . . . . . . . . . . . . . . . . . 23
Install service pack, updates . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Configure network parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Verify connectivity to the backup files . . . . . . . . . . . . . . . . . . . . . . 25
Restore backup data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Check for a super-user login . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Install the Communication Manager license and authentication files . . . . . 28
Reboot the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Integrity check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Ensure SAMP administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
If the server is a LSP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Stop and start Communication Manager. . . . . . . . . . . . . . . . . . . . . 30
Save translations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Final replacement tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Return the defective equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Job Aid: Replacing the hard drive on the
Contents

Contents
4 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
Avaya S8510 server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Replacement hardware and tools. . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Replacing either hard drive in the S8510 server. . . . . . . . . . . . . . . . . . . 34
Back up the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Remove the front bezel from the S8510 server . . . . . . . . . . . . . . . . . 35
Identify the defective drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Remove the defective hard drive from the S8510 server . . . . . . . . . . . . 38
Install the replacement drive in the S8510 server . . . . . . . . . . . . . . . . 40
Replace the front bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Monitor the drive rebuild . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Return the defective equipment . . . . . . . . . . . . . . . . . . . . . . . . . 42
Job Aid: Replacing the Avaya S8510 dual network interface. . . . . . . 43
Replacement materials and tools. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Required information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Replacing the dual NIC in the S8510 server . . . . . . . . . . . . . . . . . . . . . 44
Record Ethernet interface settings. . . . . . . . . . . . . . . . . . . . . . . . . . 44
Back up data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Power down the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Label and disconnect cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Remove the S8510 server from the rack . . . . . . . . . . . . . . . . . . . . . . . 47
Remove the cover of the S8510 server. . . . . . . . . . . . . . . . . . . . . . . . 49
Remove the defective dual NIC from the S8510 server . . . . . . . . . . . . . . . 50
Install the replacement dual NIC in the S8510 server . . . . . . . . . . . . . . . . 51
Replace the cover on the S8510 . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Install the replacement S8510 server in the rack . . . . . . . . . . . . . . . . . . 52
Check LED activity on the dual network interface card. . . . . . . . . . . . . . . 53
Configure the dual NIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Test connectivity to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Return the defective equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Job Aid: Replacing the power supply on the Avaya S8510 Server. . . . 57
Before you begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Which power supply to remove? . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Replacing the power supply in the S8510 with only one power supply . . . . . . 58
Power down the S8510 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Contents
03-602953 Issue 1 June 2008 5
Disconnect the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Remove the power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Install the replacement power supply . . . . . . . . . . . . . . . . . . . . . . 60
Restore power to the server . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Return the defective power supply . . . . . . . . . . . . . . . . . . . . . . . . 61
Replacing a power supply in the S8510 with dual power supplies. . . . . . . . . 62
Remove the defective power supply . . . . . . . . . . . . . . . . . . . . . . . 62
Replace the power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Restore power to the server . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Return the defective power supply . . . . . . . . . . . . . . . . . . . . . . . . 64
Job Aid: Replacing the SAMP on the Avaya S8510 Server . . . . . . . . 65
Required materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Hardware and tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Replacing the SAMP on the Avaya S8510 server . . . . . . . . . . . . . . . . . . 66
Power down the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Label and disconnect cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Remove the S8510 server from the rack . . . . . . . . . . . . . . . . . . . . . 68
Remove the cover of the S8510 server. . . . . . . . . . . . . . . . . . . . . . 70
Remove the defective SAMP from the S8510 server . . . . . . . . . . . . . . 71
Install the replacement SAMP in the S8510 server . . . . . . . . . . . . . . . 73
Replace the cover on the S8510 . . . . . . . . . . . . . . . . . . . . . . . . . 73
Install the replacement S8510 server in the rack . . . . . . . . . . . . . . . . 74
Update the SAMP firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Ensure SAMP administration . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Return the defective equipment . . . . . . . . . . . . . . . . . . . . . . . . . 76
Job Aid: Replacing the SAMP power supply . . . . . . . . . . . . . . . 77
Required materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Replacing the SAMP power supply for the S8510 server . . . . . . . . . . . . . . 77
Remove the defective SAMP power supply from the S8510 . . . . . . . . . . 77
Replace the SAMP power supply on the S8510 . . . . . . . . . . . . . . . . . 78
Return the defective equipment . . . . . . . . . . . . . . . . . . . . . . . . . 78
Job Aid: Replacing the USB modem. . . . . . . . . . . . . . . . . . . . 79
Required materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Remove the old modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Contents
6 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
Install the replacement modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Return the defective equipment . . . . . . . . . . . . . . . . . . . . . . . . . 80
Job Aid: Replacing the S8510 Compact Flash reader and card . . . . . 81
Required equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Remove the defective card drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Replace the card drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Replace the Compact Flash card . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Return the defective equipment . . . . . . . . . . . . . . . . . . . . . . . . . 83

03-602953 Issue 1 June 2008 7
Job Aid: Replacing the Avaya S8510 server
!Important:
Important: Always check the Avaya Support Website for Product Support Notices at http://
support.avaya.com/japple/css/
japple?PAGE=ProductArea&temp.productID=162774.
This Job Aid describes the procedures to replace an Avaya S8510 Server running Release 5.1
of Avaya Communication Manager.
Reusing hardware components
When replacing a defective S8510 server, you can re-use these components:
•Server Availability Management Processor (SAMP), see Remove the SAMP from the
defective S8510 server on page 16.
•Network interface card (NIC), see Remove the dual NIC from the S8510 server on
page 17
If either of these components are serviceable, Avaya recommends that you remove them from
the defective server and install them in the replacement server.
Replacement materials
Hardware and tools
Verify that you have the following equipment and tools on site:
•S8510 Server (MID SIZE APP SRVR FOR CM), Material ID 700449119
Note:
Note: Material ID 700449119 applies to the Avaya S8510 server, configured with 2 GB
memory, and running Communication Manager Release 5.1 or greater.
•Customer’s software CD-ROM
•Services laptop and crossover cable

Job Aid: Replacing the Avaya S8510 server
8 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
•#2 Phillips (cross-point) screwdriver
•Electrostatic wrist ground strap and mat
•Key to lock on front bezel
Note:
Note: The server ships with the front bezel unlocked and the keys taped inside it. The
customer decides whether to lock the front bezel or not. When you are finished
with the replacement procedure, please leave the server’s front bezel as you
found it.
Required information
•Server configuration information:
- Server host name
- Subnet mask
- IP addresses of the server and default gateway
•Backup information:
- Location/device
- FTP host name
-Directory
- User name
- Password
•SAMP access information:
- IP address (if connecting remotely)
-Login
- Password
Additional information
The following Avaya S8510 documents might be helpful:
•Installing the Avaya S8510 Server and its Components (03-602918)
•Avaya Server Availability Management Processor (SAMP): Avaya S8510 Server
(03-602923)

Before going to the customer site
03-602953 Issue 1 June 2008 9
Before going to the customer site
Download the following to the laptop that you will use at the customer site:
1. Communication Manager license file and authentication (password) file from the RFA site.
2. Software service pack
3. Security updates
4. Firmware upgrades:
- Server Availability Management Processor™ (SAMP)
- Media gateway
- Media module(s)
- IP telephone firmware
The Avaya Support URL is http://support.avaya.com/downloads.
The RFA URL is http://rfa.avaya.com/.
Replacing the S8510 server
Back up data
To back up the data on the S8510 Server:
1. Connect your laptop to the server’s service port using the crossover cable.
2. At a browser on your laptop log in to the Maintenance Web Pages (192.11.13.6).
Note:
Note: You might need to clear the ARP cache on your laptop (issue the arp -d
192.11.13.6 command from the laptop’s command line) before you connect to
the Maintenance Web Pages.
3. At the Maintenance Web Pages select Data Backup / Restore > Backup Now.
The Backup Now page displays.
4. In the Data Sets section select (check) all of the following data sets:
-ACP Translations and Save ACP translations before backup.
- Server and System Files

Job Aid: Replacing the Avaya S8510 server
10 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
- Security Files
5. Select the Backup Method:
- Local PC Card (the USB-connected Compact Flash reader/card)
Tip:
Tip: Backing up to the USB Compact Flash saves remastering time.
- Network Device: enter the customer-supplied information for:
•User Name
•Password
•Host Name
•Directory
6. Click Start Backup.
Wait for the message indicating that the backup was successful.
Power down the server
Shutdown the S8510 server using either the Maintenance Web Pages or the manual Shutdown
button on the faceplate.
1. On the Maintenance Web Pages, select Server > Shutdown Server.
The Shutdown Server page displays.
a. Select the Delayed Shutdown option.
b. Uncheck the Restart server after shutdown checkbox.
c. Click Shutdown.
2. If you cannot access the Maintenance Web Pages, you can manually power down the
server by pressing the power button on the front panel (Note 1 in Figure 1).
Note:
Note: The system’s Advanced Configuration and Power Interface (ACPI) is disabled,
meaning that power is cut off immediately after pressing the power button.

Replacing the S8510 server
03-602953 Issue 1 June 2008 11
Figure 1: Avaya S8510 front panel
3. Continue only after the server has powered down and the power-on indicator light (Note 1 in
Figure 1) is out.
Label and disconnect cabling
Be sure to label and disconnect the following connections:
1. Label and disconnect the power cord(s) from the power supply(ies) at the back of the
server.
2. Label and disconnect the Ethernet cable from the dual NIC at the back of the server.
3. Label and disconnect the power cord from the SAMP at the back of the server.
4. Label and disconnect the USB modem cable from the USB port on the SAMP at the back of
the server.
5. Label and disconnect the LAN connection (if used) from the Ethernet port on the SAMP at
the back of the server.
Figure notes:
1. Power-on indicator, power button 5. USB 2.0 connectors
2. Nonmaskable Interrupt (NMI) button
(disabled) 6. Video connector (not used)
3. System identification button (used to
locate equipment within the rack) 7. Hard disk drives
4. LCD display (system ID, status
information, and system error
messages)
8. Slimline CD/DVD drive
01
III
hw8510fn LAO 020108
7
1 2 3 4 5 6
8

Job Aid: Replacing the Avaya S8510 server
12 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
Remove the S8510 server from the rack
To remove the S8510 server from the rack:
1. Ensure that all cables are labeled and disconnected from the server.
2. Loosen the captive screws on both sides of the server (Note 1 in Figure 2).

Replacing the S8510 server
03-602953 Issue 1 June 2008 13
Figure 2: Remove the S8510 server from the rack
3. Slide the server clear of the rails (Note 2 in Figure 2).
Figure notes:
1. Loosen the captive
screws. 3. Release the rail lock.
2. Slide the server clear of
the rails.
hw8510rk LAO 040308
13
2

Job Aid: Replacing the Avaya S8510 server
14 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
4. Release the rail lock by pushing the level in as you slide the server out of the rack (Note 3 in
Figure 2).
If you are re-using the SAMP/dual NIC
If you are re-using the SAMP and/or the dual NIC from the defective server, complete this
section. Otherwise, omit this section and continue with Install the replacement S8510 server in
the rack on page 20.
Remove the cover of the S8510 server
!CAUTION:
CAUTION: Ensure that the power is completely removed from the server: power cords must
be detached from the power supply(ies) and the SAMP.
To remove the cover from the S8510 server to access internal components:
1. Use a #2 Phillips (cross-point) screwdriver to rotate the latch release lock counter-clockwise
to the unlocked position (Note 1 in Figure 3).

Replacing the S8510 server
03-602953 Issue 1 June 2008 15
Figure 3: Removing the cover of the S8510 server
2. Lift the latch up to unlock (Note 2 in Figure 3).
3. Lift the cover back then straight up and set it aside (Note 3 in Figure 3).
Figure notes:
1. Turn the latch release lock
counter-clockwise to the unlocked
position.
3. Slide the cover back then lift straight
up to remove.
2. Lift the latch up to unlock.
1
2
3
hw8510cr LAO 021008

Job Aid: Replacing the Avaya S8510 server
16 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
Remove the SAMP from the defective S8510 server
!CAUTION:
CAUTION: The SAMP has separate power source than the server’s. You must remove all
power from the server and the SAMP card before starting this procedure.
ELECTROSTATIC ALERT:
ELECTROSTATIC ALERT: Take precautions against electrostatic discharge: wear a wrist strap connected to
an approved ground.
The SAMP card resides in a PCI expansion card riser at the rear of the S8510 server. To
remove the defective SAMP from the riser:
1. Lift the release latches located at the left side of the PCI expansion card riser as shown in
Figure 4.
Figure 4: Removing/replacing the S8510 SAMP card
Figure notes:
1. Press the release latches
on the PCI expansion
card riser.
3. Remove the SAMP from the
expansion slot.
2. Remove the cable from
the SAMP. 4. Remove the ribbon cable from the motherboard.
hw85smpr LAO 040308
1
2
3
4

Replacing the S8510 server
03-602953 Issue 1 June 2008 17
2. Disconnect the cable assembly from the SAMP (Note 2 in Figure 4). Set the cable aside;
you will not re-use the cable but will return it to Avaya with the SAMP.
3. Remove the SAMP card by pulling it gently out of the expansion slot in the riser assembly
(Note 3 in Figure 4).
4. .Remove the ribbon cable from the motherboard (Note 4 in Figure 4).
Install the SAMP in the S8510 server
To install the SAMP in the S8510 server, refer to Figure 4 and using the steps in reverse order:
1. Connect the ribbon portion of the SAMP cable assembly to the motherboard (Note 4 in
Figure 4).
2. Carefully grasp the SAMP by the outer edges and align it with the opening on the PCI
expansion slot riser assembly. Press the SAMP firmly into the expansion slot (Note 3 in
Figure 4).
!CAUTION:
CAUTION: Make sure the SAMP card is completely seated in the expansion slot before you
apply power to the S8510 server. Incomplete insertion might cause damage to
the system board or to the SAMP card.
3. Connect the other end of the SAMP cable assembly to the SAMP (Note 2 in Figure 4).
4. Press the PCI expansion card riser release latches (Note 1 in Figure 4) to secure the SAMP
and the riser assembly.
Remove the dual NIC from the S8510 server
To remove the dual NIC from the S8510 server:
1. Press the release latches on the PCI expansion card riser (Note 1 in Figure 5).

Job Aid: Replacing the Avaya S8510 server
18 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
Figure 5: Removing and replacing the dual NIC in the S8510
2. Grasp the dual NIC by its edges and carefully pull it straight out of the PCI expansion card
riser slot (Note 2 in Figure 5).
Install the dual NIC in the S8510 server
To install the dual NIC in the S8510 server:
1. Carefully grasp the NIC by its edges and position it so that the card-edge connector aligns
with the expansion-card slot on the PCI riser board (Note 2 in Figure 5).
2. Insert the card-edge connector firmly into the PCI expansion card riser until the card is fully
seated.
3. Close the PCI expansion card riser latch (Note 1 in Figure 5).
Figure notes:
1. Press the release latch on the
PCI expansion card riser. 2. Pull the dual NIC card straight outof the slot.
hw85nicr LAO 040308
11
2

Replacing the S8510 server
03-602953 Issue 1 June 2008 19
Replace the server cover
To replace the cover on the S8510 server use Figure 6 in reverse order.
!WARNING:
WARNING: Ensure that the SAMP cable and any other internal cables are clear of the cover
before replacing it on the server.
1. Place the cover on top of the server, aligning it with the J hooks on the sides.
Figure 6: Replacing the cover on the S8510 server
2. Slide the cover forward.
3. Push the latch down to lock (Note 2 in Figure 6).
4. Rotate the latch release lock clockwise to secure the cover (Note 1 in Figure 6).
5. Place the customer’s Communication Manager CD in the optical drive tray (Note 8 in
Figure 1) of the replacement server.
Figure notes:
1. Latch release lock 3. Slide the cover back then lift straight
up to remove.
2. Push the latch down to lock. 4. Align the cover with the J hooks on
each side of the server.
1
2
3
hw8510cr LAO 021008

Job Aid: Replacing the Avaya S8510 server
20 Job Aids for Field Replacements (FRUs) for the Avaya S8510 Server
Install the replacement S8510 server in the rack
To install the replacement S8510 server back in its rack:
1. Install the server onto the slide rails in the rack (see Note in Figure 2.
2. Reconnect the Ethernet cable to the dual NIC at the back of the server.
3. Reconnect the power cord to the SAMP at the back of the server.
4. Reconnect the USB modem cable to the USB port on the SAMP at the back of the server.
5. Reconnect the LAN connection (if used) from the Ethernet port on the SAMP at the back of
the server.
6. Reconnect the power cord(s) to the power supply(ies) at the back of the server.
7. Push the server completely into the rack and secure into place with the captive screws on
both sides of the server.
Install Communication Manager
Set TELNET parameters
The Microsoft TELNET application might be set to send a carriage return (CR) and line
feed (LF) each time you press Enter. The installation program interprets this as two key
presses. You must change this before you TELNET to the server.
Note:
Note: This procedure is performed entirely at your laptop, not on the server.
1. Click on Start > Run to open the Run dialog box.
2. Type telnet and press Enter to open a Microsoft TELNET session.
3. Type unset crlf and press Enter.
4. Type display and press Enter to confirm that either Sending only CR or Line feed
mode--causes the return key to send CR displays.
5. Type quit or close the TELNET window by clicking on the Xin the upper-right corner.
This closes the TELNET connection and resets your Microsoft TELNET defaults, which do
not need to be set each time you use TELNET.