Avaya VSP 4000GSX Series User manual

Release 4.0.50
NN46251-309
Issue 02.02
July 2015
Installation Job Aid for Avaya VSP 4000 4450GSX series
How to get help
To access the complete range of services and support that Avaya provides, go to www.avaya.com.
You can also go to www.avaya.com/support to access the following pages:
• technical documentation
• product training
• technical support
If you purchased a service contract for your Avaya product from a distributor or authorized reseller
and you need assistance, contact the technical support staff for that distributor or reseller.
Notices
Notice paragraphs alert you about issues that require your attention. The following paragraphs
describe the types of notices used in this guide.
Note:
Notes provide tips and useful information regarding the installation and operation of Avaya
products.
Electrostatic alert:
ESD
ESD notices provide information about how to avoid discharge of static electricity and
subsequent damage to Avaya products.
Caution:
Caution notices provide information about how to avoid possible service disruption or damage to
Avaya products.
Warning:
Warning notices provide information about how to avoid personal injury when working with
Avaya products.
© 2015 Avaya Inc. Installation Job Aid for Avaya VSP 4000 4450GSX series 1

Voltage:
Danger — High Voltage notices provide information about how to avoid a situation or condition
that can cause serious personal injury or death from high voltage or electric shock.
Danger:
Danger notices provide information about how to avoid a situation or condition that can cause
serious personal injury or death.
Safety messages
Warning:
Installation must be performed by qualified service personnel only. Read and follow all warning
notices and instructions marked on the product or included in the documentation.
Voltage:
This equipment relies on the building's installation for overcurrent protection. Ensure that a fuse
or circuit breaker no larger than 120 VAC, 15 A U.S. (240 VAC, 16 A International) is used on
the phase conductors.
Caution:
This device is a Class A product. In a domestic environment, this device can cause radio
interference, in which case the user may be required to take appropriate measures.
Caution:
When mounting this device in a rack, do not stack units directly on top of one another in the
rack. Each unit must be secured to the rack with appropriate mounting brackets. Mounting
brackets are not designed to support multiple units.
Voltage:
Use only power cords that have a grounding path. Without a proper ground, a person who
touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the
switch can result in excessive emissions.
Warning:
Disconnecting the power cord is the only way to turn off power to this device. Always connect
the power cord in a location that can be reached quickly and safely in case of an emergency.
Warning:
Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into
an optical fiber or connector port. Always assume that fiber optic cables are connected to a light
source.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 2

Caution:
Risk of high current and board burn out if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
Warning:
The lithium battery is not field replaceable. It must only be removed and replaced by authorized
personnel. Contact Avaya Technical Support for assistance if the battery requires replacement.
Before you begin
Ensure the area where you install and use the VSP 4000 switch meets the following environmental
requirements:
• Ambient temperature between 32° and 122° F (0° and 50° C)
• Relative humidity between 0% and 95% noncondensing
• No nearby heat sources such as hot air vents or direct sunlight
• No nearby sources of severe electromagnetic noise
• No excessive dust
• Adequate power source within six feet; one 15-Amp circuit required for each power supply
• At least 2 inches (5.08 cm) on all sides of the switch unit for ventilation
• Adequate space at the front and rear of the switch for access to cables
If you are installing a single VSP 4000 switch on a table or shelf, ensure the surface can support at
least 15 to 20 pounds (7 to 9 kilograms).
Installing the Avaya VSP 4450GSX series switches
The VSP 4450GSX series consists of the 4450GSX-PWR+, 4450GSX-DC and the TAA compliant
versions.
Warning:
Do not use the ERS to VSP conversion kit (part number EC4810003-3.0) with these chassis .
The kit is incompatible with the VSP 4450GSX series switches.
Note:
A factory-supplied 4450GSX series switch has a USB slot but no USB device or cover.
Installing the Avaya VSP 4000 switch on a table or shelf
You can install a single Avaya VSP 4000 switch on any flat surface. The surface must support the
combined weight of the switch and attached cables (from 15 and 20 pounds [7 to 9 kilograms]).
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 3

To install an Avaya VSP 4000 on a table or shelf, perform this procedure.
1. Attach the included rubber footpads on the bottom of the switch at the locations indicated.
2. Set the switch on a table or shelf as illustrated below. Allow at least 2 inches (5.1
centimeters) on each side for proper ventilation and at least 5 inches (12.7 centimeters) at
the back for power cord clearance.
Installing the Avaya VSP 4000 switch in an equipment rack
To install an Avaya VSP 4000 switch in an equipment rack, perform this procedure.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 4

Prerequisites for installing the Avaya Virtual Services Platform 4000 in an equipment rack:
• Ensure that you have a space of 1.75 inches (4.45 centimeters) in height for each switch in an
EIA or IEC-standard 19-inch (48.2-centimeter) equipment rack.
• The rack is bolted to the floor and braced if necessary.
• The rack is grounded to the same grounding electrode used by the power service in the area.
The ground path must be permanent and must not exceed 1 Ohm of resistance from the rack
to the grounding electrode.
1. Attach the L-bracket to each side of the switch using a #2 Phillips screwdriver as illustrated
below.
2. Slide the switch into the rack as illustrated.
3. Insert and tighten the rack-mount screws.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 5

Installing SFP transceivers
Install SFP transceivers by performing this procedure.
1. Remove the transceiver from the protective packaging.
2. Verify that the transceiver is the correct model for the network configuration.
3. Grasp the transceiver between your thumb and forefinger.
4. Insert the transceiver into the proper module on the switch. Apply a light pressure to the
transceiver until it clicks and locks into position in the module.
5. Remove the dust cover from the transceiver optical bores.
Removing SFP transceivers
Remove SFP transceivers by performing this procedure.
1. Disconnect the network fiber cable from the transceiver.
2. Use the locking mechanism on the transceiver to release it. The locking mechanism varies
from model to model as illustrated below.
3. Slide the transceiver from the module slot.
4. If the transceiver does not slide easily from the module slot, use a gentle side-to-side rocking
motion while firmly pulling the transceiver from the slot.
5. Attach a dust cover over the fiber-optic bores and store the transceiver in a safe place until
you need it.
Important:
Discard transceivers in accordance with the proper laws and regulations.
Power specifications for the Avaya VSP 4450GSX series switches
This section describes the regulatory AC and DC power specifications for the Avaya VSP 4000
4450GSX series switches.
The following table describes the regulatory AC power specifications for the VSP 4450GSX-PWR+
switch and its TAA compliant version. The regulatory AC power specifications are based on the
maximum rated capacity of the power supplies and are not based on typical power consumption,
which is lower.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 6

Table 1: AC power specifications
4450GSX-PWR+
Input Current: 12A/6A
Input Voltage (rms): 100 to 240VAC at 50 to 60 Hz
Power Consumption: 248 W maximum
Thermal Rating: 508 BTU/Hr maximum
Inrush Current: 70 A maximum
Turn on Condition: 1 second maximum after application of AC power
Important:
12 V output rise time, from 10 to 90 per cent, must be the maximum of 50 ms and monotonic under all
defined input and output conditions.
The following table describes the regulatory DC power specifications for the VSP 4450GSX-DC
switch. The regulatory DC power specifications are based on the maximum rated capacity of the
power supplies and are not based on typical power consumption, which is lower.
Table 2: DC power specifications
4450GSX DC
Input Current: 25A
Input Voltage: 12VDC
Power Consumption: • Typical: 116W
• Maximum: 164.6W
Thermal Rating: 508 BTU/Hr
Power supply power specifications for the VSP 4450GSX series switches
The Avaya VSP 4450GSX series switches support two external field replaceable AC and DC power
supplies. One power supply ships with the chassis. You can install a secondary power supply to
provide redundancy, load sharing, and to add Power over Ethernet Plus (PoE+) power budget on
PWR+ models.
AC power supply power specifications
The VSP 4000 4450GSX-PWR+, including the TAA compliant version, supports dual 54V 1000W
Power over Ethernet Plus (PoE+) AC power supplies.
Important:
Ensure that you use only 1000W power supplies (both primary and secondary) on VSP 4000
PWR+ models.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 7

Figure 1: 1000W AC power supply
Connector
The 1000W AC power supply uses an IEC 60320 C16 AC power cord connector. The AC power
cord is in close proximity to the hot air exhaust, and supports high operating temperatures.
Figure 2: IEC 60320 C16 connector
Power over Ethernet Plus (PoE+) specifications
Table 3: Avaya VSP 4450GSX-PWR+ PoE+ specifications
Maximum PoE+ W Average PoE+ W on 12 ports
835W with one power supply
1835W with two power supplies
17.8W or 32.4W (802.3.at) — 1 power supply
• The VSP 4450GSX-PWR+ can support 802.3af 17.8W or 32.4W on each port with one power
supply installed. You can add a second power supply for redundancy.
Related Links
DC power supply power specifications on page 8
DC power supply power specifications
The VSP 4450GSX-DC switch uses field replaceable 300W DC PSUs.
The following table describes the DC power supply specifications for this switch.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 8

Table 4: DC power supply specifications
Description DC-DC-12V-300 W
Output power 300 W
Input voltage 48 V DC
Input current 10 A
Output voltage 12 V DC
Output current 25 A
Related Links
Power supply power specifications for the VSP 4450GSX series switches on page 7
Installing the Avaya Virtual Services Platform 4000 power supply
You must install at least one power supply before using the switch. Avaya VSP 4000 models
support two field replaceable external power supplies. If supported, you can install an optional
second power supply for redundancy, load sharing, or to provide additional PoE+ power budget.
Perform the following procedure to install an external power supply into your switch.
Note:
Avaya VSP 4000 hardware can vary. This procedure only applies to hardware models with field
replaceable power supplies.
1. If a blanking plate covers the required power supply slot, remove the blanking plate before
attempting to insert the power supply.
2. Insert each power supply into a rear power supply slot.
3. Verify that each power supply is fully seated in the slot. Secure the power supply with the
two thumb screws.
Note:
The switch chassis can prevent an incorrect installation of a power supply. If you insert a
power supply upside down, it will not fully insert and the thumb screws will not engage.
4. Once you install a power supply, you can proceed with connecting AC power.
Note:
Do not connect an AC and DC power supply in the same chassis. Load sharing may be
affected.
Important:
You can hot swap power supplies while the switch is operational. One power supply is required
for continued switch operation. PoE+ load reductions can occur if you remove one power supply
while the switch is operating with dual power supplies.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 9

Connecting to AC power
To connect AC power to the switch, you need an appropriate AC power cord as described in the
following table, also see the following table for plug specifications.
Table 5: International power cord specifications
Country and Plug Specification Specifications Typical Plug
Continental Europe:
• CEE7 standard VII male plug
• Harmonized cord (HAR marking on the outside of the cord
jacket to comply with the CENELEC Harmonized
Document HD-21)
• 220 or 230VAC
• 50 Hz
• Single phase
United States of America, Canada, and Japan:
• NEMA5-15P male plug
• UL-recognized (UL stamped on cord jacket)
• CSA-certified (CSA label secured to the cord)
• 100 or 120VAC
• 50–60 Hz
• Single phase
United Kingdom:
• BS1363 male plug with fuse
• Harmonized cord
• 240VAC
• 50 Hz
• Single phase
Australia:
• AS3112-1981 male plug
• 240VAC
• 50 Hz
• Single phase
Danger:
Using power cords with a proper grounding path
Use only power cords that have a grounding path. Without a proper ground, a person who
touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the
switch can result in excessive emissions.
Connecting to DC power
To connect DC power to the switch, use the short power cable that is provided with the switch.
July 2015 Installation Job Aid for Avaya VSP 4000 4450GSX series 10