Aventura VENDOMA-MPG User manual
VENDOMA-MPG DVR
(Digital Video Recorder)
Hardware Installation Guide
Version 1.00.00
© 2004 Aventura Technologies, Inc.
VENDOM
A
DV
R
t
INDEX
1. Features 4
2. Installation Notes 6
3. Products and Components 7
4. Install Capture Board 8
4-1. Vendoma MPG 12004 Board 8
4-2. Vendoma MPG 24008 Board Type A 10
4-3. Vendoma MPG 24008 Board Type B 12
4-4. Vendoma MPG 48016 Board Type A 14
4-5. Vendoma MPG 48016 Board Type B 17
5. Pin number 20
5-1. Vendoma MPG 12004 Board 20
5-2. Vendoma MPG 24008, 24016 Board 21
5-3. Accessories 23
6. RS422/485 Converter 25
7. Vendoma System 27
9-1. Front View 27
9-2. Rear View 28
8. P/T/Z Camera Connection Guide 30
2
VENDOM
A
DV
R
t
Preface
This guide book describes the individual hardware components and how to install them.
For a description of the software and how to install it, please refer to the Installation and User Guide
provided with your unit.
This guide is for the following Aventura Technologies products: Vendoma MPG 12004, 24008, and
48016 capture boards.
Board shapes and item names may be slightly different than those in this manual.
We are looking forward to hearing your comments about our DVR. Should you have any questions,
please contact us.
Telephone: 1 (800) 870 5330
Fax: (631) 434 7000
www.aventuratechnologies.com
www.vendoma.com
3
VENDOM
A
DV
R
t
1. Features
About Your Vendoma-MPG DVR
4, 8, or 16 Camera Input/Output
Normal input condition: 75 Ohm, 1 Volt
1 4, 8, or 16 Sensor Inputs
4 channels, 4 sensors (16 sensors optional)
8 channels, 8 sensors (16 sensors optional)
16 channels, 16 sensors
Note: DC 12 Volt power is required
1-16 Digital Outputs (Relay Outputs)
4 channels: 4 Relays (16 sensors optional)
8 channels 4 Relays (16 sensors optional)
16 channels 8 Relays (16 sensors optional)
Note: DC 12 Volt power is required
Sound Recording and Two Way Communications Capabilities
16 channel sound recording.
Sound can be recorded locally on 16 channels; however, two-way voice communication can
be done remotely on only one channel
Multi-Viewing
You can view 1, 4, 9, 10, or 16 cameras on your screen.
A full screen option is also available.
Pan/Tilt/Zoom/Focus Remote Control
You can manipulate your Pan/Tilt/Zoom cameras via Vendoma Main.
Auto Rebooting System
If this feature is enabled, when the DVR detects a malfunction in the system, the system
reboots and corrects the malfunctions. This is also called the Watchdog feature.
4
VENDOM
A
DV
R
t
Motion Detection and Sensor Trigger
You can set the DVR to record only when movements are detected, which saves storage
space.
Scheduled recording
You can specify a recording schedule.
Data Backup and Auto Backup
Backed up data can be transferred to different media, such as DAT, CD, or DVD. You can
also back up the data from a specific camera and view the date and time stamp on the
footage. Like the scheduled recording, the data backup program can also be scheduled.
Digitalized Video Search
Recorded data can be played back digitally on one or more cameras at a time.
By entering the date and the time, you can retrieve an image from the video. You can also
edit, enlarge, save, and print images separately.
Network Support (TCP/IP, ISDN, and PSTN Support)
With network software, you can log in to Vendoma-Main remotely to view live recording,
search and save video data locally, and even change the DVR’s settings.
5
VENDOM
A
DV
R
t
2. Installation Notes
We recommend the following for ideal performance:
Intel chip motherboards
Intel Pentium 4 or equivalent (Nothing lower than a 2.0 GHz Celeron)
256 MB or more of RAM
80 GB or more hard disk space
If you try to use a 160 GB hard drive or higher, your operating system should be updated
with the latest service pack.
Windows 2000 or Windows XP
Screen savers and power management must be disabled
System standby and energy saving mode for both the hard drive and the monitor should be disabled
For sound recording DirectX 8.0 or higher must be installed
ATI video cards are recommended, but any product higher than a 128 Radeon can be used
6
VENDOM
A
DV
R
t
3. Products and Components
VENDOMA-MPG 12004
(120 Frames per second, 4 Channels)
VENDOMA-MPG 24008
(240 Frames per second, 8 Channels)
MPG 12004 Accessory
MPG 24008Accessory Type A MPG 24008 Accessory Type B
MPG 48016Accessory Type A MPG 48016Accessory Type B
The boards pictured above and their accessories may be subject to change by hardware upgrade.
7
VENDOM
A
DV
R
t
4. Install Capture Board
4-1. VENDOMA MPG 12004 Board
MPG 12004 Board andAccessories
MPG 12004 Board TV-Out, Sensor, Relay
Video Input Audio Input
Watchdog
8
VENDOM
A
DV
R
t
1 Connect audio input cable
2 Connect video input cable
3 Connect TV-OUT cable
4 Connect sensor relay cable
5 Connect Watchdog cable
Assembly View
Note:
1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the
Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in
next to the Watchdog on the DVR card.
2. If the Watchdog cable and/or the Reset switch are connected incorrectly, the system will not
reboot and you may not have video. Try reconnecting the pins to restore the video.
9
VENDOM
A
DV
R
t
4-2. VENDOMA MPG 24008 Board Type A
MPG 24008 Board andAccessories
MPG 24008 Board TV-Out, Sensor, Relay
Video Input cable Audio Input cable
Watchdog
10
VENDOM
A
DV
R
t
1 Connect audio input cable
2 Connect video input cable
3 Connect TV-OUT cable
4 Connect sensor relay cable
5 Connect Watchdog cable
Assembly View
Note:
1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the
Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next
to the Watchdog on the DVR card.
2. If the Watchdog cable and/or the Reset switch are connected incorrectly, the system will not
reboot and you may not have video. Try reconnecting the pins to restore the video.
11
VENDOM
A
DV
R
t
4-3. VENDOMA MPG 24008 Board Type B
MPG 24008 Board andAccessories
MPG 24008 Board BNC Back panel
Audio Input cable Watchdog
Video Input cable Sensor & relay cable
12
VENDOM
A
DV
R
t
1 Connect Audio Input cable
2 Connect BNC cable
3 Connect Back panel cable
4 Connect Sensor Relay cable
5 Connect Watch dog cable
Assembly View
Note:
1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the
Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next
to the Watchdog on the DVR card.
2. If the Watchdog cable and/or the Reset switch are connected incorrectly, the system will not
reboot and you may not have video. Try reconnecting the pins to restore the video.
13
VENDOM
A
DV
R
t
4-4. Vendoma MPG 48016 Board (Board TYPE A)
MPG 48016 Board andAccessories
MPG 24008-1 Board MPG 24008-2 Board
Video Input cable Audio Input cable
TV-Out, Sensor, Relay 2EA Watchdog TV-OUT Loop
14
VENDOM
A
DV
R
t
1 Connect Video cable
(MPG 24008-1 & MPG 24008-2)
2 Connect Audio cable
(MPG 24008-1 & MPG 24008-2)
3 Connect TV-OUT cable
(MPG 24008-1 Only)
4 Insert Sensor Relay
(MPG 24008-1 & MPG 24008-2)
5 Connect Watch dog cable
(MPG 24008-1 Only)
6 MPG 24008-1 & MPG 24008-2
Hook up TV-OUT Loop
15
VENDOM
A
DV
R
t
Assembly View
1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the
Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next
to the Watchdog on the DVR card.
2. If the Watchdog cable and/or the Reset switch are connected incorrectly, the system will not
reboot and you may not have video. Try reconnecting the pins to restore the video.
16
VENDOM
A
DV
R
t
4-5. Vendoma MPG 48016 Board TYPE B
MPG 48016 Board andAccessories
MPG 24008-1 Board MPG 24008-2 Board
Video Input cable Audio Input cable
Watchdog TV-OUT Loop Sensor & relay cable
17
VENDOM
A
DV
R
t
1 Connect Audio cable
( MPG 24008-1 & MPG 24008-2)
2 Connect BNC cable
( MPG 24008-1 & MPG 24008-2)
3 Connect BNC cable
( MPG 24008-1 & MPG 24008-2)
4 connect Back panel cable
5 Insert Sensor Relay
( MPG 24008-1 & MPG 24008-2)
6 Connect Watch dog cable
( MPG 24008-1 Only)
18
VENDOM
A
DV
R
t
7 MPG 24008-1 & MPG 24008-2
Hook up TV-OUT Loop
Assembly View
1. After connecting the Watchdog cable, the other end of the cable must be plugged in to the
Reset pin of the PC’s motherboard. The Reset switch from the PC must be plugged in next to
the Watchdog on the DVR card.
2. If the Watchdog cable and/or the Reset switch are connected incorrectly, the system will not
reboot and you may not have video. Try reconnecting the pins to restore the video.
19
VENDOM
A
DV
R
t
5. Pin numbers
5-1. MPG4 12004 Capture Board
Composite-OUT
Composite-Out
Video In
Audio In
Sensor & Relay(digital I/O)
Pin name Pin number
Sensor Input 0-3 1-4
Input Common 0-1 17, 18
Relay(Digital) Output 0-3 19-22
Output Common 0-1 23, 24
Watchdog
Pin name Pin number
Signal Ground 1, 3
Reset Signal 2, 4
20
This manual suits for next models
3
Table of contents
Other Aventura DVR manuals
