Avenview MLT-EDGEPRO-2X2E User manual

VIDEOWALLSVIDEOPROCESSORS
VIDEOMATRIXSWITCHES
EXTENDERSSPLITTERSWIRELESS
CABLES&ACCESSORIES
ControlYour Video
2X2 4K DUAL CHANNEL, CURVED SCREEN
EDGE BLENDER
User Guide
Model #: MLT-EDGEPRO-2X2E

Page|2
www.avenview.com
Revision History
Rev
Changes
Date
1.0
Initial Release
2019/07/11
Copyright
© 2018 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with
Avenview Inc. (“Avenview”) products. Avenview makes no
representations or warranties with respect to the accuracy or
completeness of the contents of this publication and reserves the
right to make changes to specifications and product descriptions at
any time without notice. No license, whether express, implied, or
otherwise, to any intellectual property rights is granted by this
publication. Except as set forth in Avenview Standard Terms and
Conditions of Sale, Avenview assumes no liability whatsoever, and
disclaims any express or implied warranty, relating to its products
of Avenview Inc. is strictly prohibited.

Page|3
www.avenview.com
Table of Contents
1. Getting Started 6
1.1. Important Safeguards 6
1.2. Safety Instructions 6
1.3. Regulatory Notices 7
2. Introduction 8
3. Features 9
4. Package Contents 11
5. Specifications 12
6. Basic operation & setting 13
6.1. Connecting the inputs 13
6.2. Connecting the outputs 14
6.3. Input / Output selection & LED Indicators 14
6.3.1.Input source selection
6.3.2.Output resolution selection
6.3.3.LED indicators
6.4. System connection and Power On 16
6.5. HDMI Loop Out for daisy chain connection 17
6.6. System settings: Box ID, RS232, Ethernet 17
6.6.1. Box ID
6.6.2.RS232 settings
6.6.3.Ethernet
6.7. How to use IR Remote Control 19
6.8. Full screen and native aspect ratio 20
6.9. Image rotation and flip 21
6.10. Color adjustment 21
6.10.1. Global color adjustment: [Picture]
6.10.2. Pre-set Color Temperature and independent RGB color adjustment
6.10.3. Color adjustment function under [Edge Blend] menu adjustment
6.11. OSD Lock and unlock 23
6.12. System synchronization 23
7. Project Plan and preparation for Edge Blending 24
7.1. Determine source signal resolution 24
7.2. System synchronization 25
7.3. Relation between Overlap pixels and geometry alignment accuracy 25
7.4. Get installation data from Excel Spread Sheet 27
7.5. Apply Spread Sheet data for projector installation and EdgePro setting 29
7.5.1.Installation data from Spread Sheet from previous section
7.5.2.Mark projection region for each projector

Page|4
www.avenview.com
7.5.3.Installation the projector
7.6. Projector settings before edge blending 30
7.7. EdgePro settings before edge blending 31
8. . Geometry Alignment 31
8.1. 8.1. Select the right Grid Pattern for geometry alignment 31
8.2. 8.2. Grid pattern pixel size selection 32
8.3. 8.3. Geometry alignment 33
8.3.1. Geometry alignment through remote controller
8.3.2. Activate grid pattern
8.3.3. [2x2] 4 corner geometry alignment
8.3.4. [3x3], [5x3], [9x5] warp alignment
8.3.5. Linearity grid line adjustment
8.3.6. Corner [Wall] geometry adjustment
8.3.7. [Gwarp]
9. [Video Wall] settings 42
9.1. [Zoom]: split the signal source 43
9.2. [Pan]: assign image location 43
9.3. [Overlap]: crop the right image for each projector 44
9.4. [Position]: shift image position without changing image size 45
10. 10. [Edge Blend] settings 45
10.1. [Edge] selection location and set edge blending value 46
10.2. [Shift]: shift Edge Blend position and execute Edge Mask 47
10.3. [Gamma]: color correction in edge blending area 47
10.4. Black level uplift: [Offset] & [Corner] adjustment 49
10.4.1. [Offset]
10.4.2. [Corner]
10.5. [Color]: Individual projector white balance and color correction 52
10.6. Edge [Mask} 53
10.7. [Grid] (Please see more details in Section 8.2) 54
10.8. Final image quality fine-tuning 55
11. Example for 3 projector edge blending procedures 56
11.1. Get detailed edge blending information through AVENVIEW Excel Spread Sheet 56
11.1.1.Assumption
11.1.2.Excel calculation
11.2. Mark image location and install the projectors 57
11.3. System connection 58
11.4. Projector settings 59
11.5. EdgePro settings 59
11.6. Geometry alignment 59
11.7. Video wall settings 62
11.8. Edge blending setting 63

Page|5
www.avenview.com
11.9. Final image quality fine-tuning 64
12. Save/Load system settings 65
13. Multiple unit applications 66
13.1. System connection in multiple unit edge blending 66
13.2. Content overlap setting issue 68
13.3. Convenient setting in multiple unit application 69
13.3.1.Setup by remote controller
13.3.2.Setup by Ethernet
14. WebGUI and Windows PC Tool 69
14.1. WebGUI 70
14.2. Windows PC Tool 71
15. 15. Advanced applications and settings 71
15.1. Immersive display with multiple projectors 71
15.1.1.Assumption
15.2. Portrait edge blending 74
15.3. Flexible display 75
15.4. Unique content displayed in each projector 76
15.5. Complete system aspect ratio adjustment 77
16. 16. Miscellaneous settings 78
16.1. Helpful tips for edge blending 78
16.2. System structure and control 79
16.2.1.System Structure
16.2.2.OSD Command Execution in Channel 1 & Channel 2
16.3. EDID setting 80
16.4. HDMI vs. DVI output signal 81
16.5. System standby and automatically turn off output signal 82
16.6. Change background color 82
16.7. Turn off Splash screen Logo 82
16.8. Limitation in image flip and rotation 83
16.9. Limitation in audio output 83
17. Troubleshooting 83
17.1. Front panel LED indicators 83
17.2. Intermittent or loss of input signal 83
17.3. Video quality issues 84
17.4. Image position shift after installation 84
17.5. System crash and malfunction 85
17.6. Synchronization issue in the outputs 85

Page|6
www.avenview.com
SECTION 1: GETTING STARTED
IMPORTANT SAFEGUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover
•Any product, on which the serial number has been defaced, modified or removed.
•Damage, deterioration or malfunction resulting from:
•Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
•Repair or attempted repair by anyone not authorized by us.
•Any damage of the product due to shipment.
•Removal or installation of the product.
•Causes external to the product, such as electric power fluctuation or failure.
•Use of supplies or parts not meeting our specifications.
•Normal wear and tear.
•Any other causes which does not relate to a product defect.
•Removal, installation, and set-up service charges.
SAFETY INSTRUCTIONS
The HDMLT-C5SP-4 and HDMLT-C5SP-8 HDMI Splitter 1x4 / 1x8 Over CAT5E/CAT6 50m has been tested for
conformance to safety regulations and requirements, and has been certified for international use. However, like all
electronic equipments, the HBT-C6POE-SP8 should be used with care. Read the following safety instructions to
protect yourself from possible injury and to minimize the risk of damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls
or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.

Page|7
www.avenview.com
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols
Description
ONLY USE THE PROVIDED POWER CABLE
OR POWER ADAPTER SUPPLIED. DO NOT
TAMPER WITH THE ELECTRICAL PARTS.
THIS MAY RESULT IN ELECTRICAL SHOCK
OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING
SO WILL VOID THE WARRANTY AND
CONTINUED USE OF THE PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE
TO STATIC. PLEASE ENSURE IF RACK
MOUNTED OR INSTALLED ON A SURFACE,
IT SHOULD BE IN A GROUNDED
ENVIROMENT.

Page|8
www.avenview.com
2. Introduction
EdgePro is a dual channel professional curved screen edge blending processor designed for advanced
edge blending, image warping, stacking, projection mapping and much more. 4 inputs (2x HDMI, 1x
DP, 1x VGA) and 2x HDMI outputs are featured in EdgePro. Input supports up to 4096*2160 @60Hz
with 4:4:4 full color sampling. Output supports up to 2048*1080 @60Hz. It is integrated with 10-bit
high end processor, 3D motion adaptive de-interlace, low angle smooth algorithm, 3:2/2:2 pull-down
and supports non-VESA standard input timing for connecting with various input sources. Advanced
warp technology is embedded in the EdgePro. Control is achieved via IR controller or WebGUI to
perform edge blending and sophisticated geometry alignment up to 9x5 grids and 17x17 grids from
Windows PC tool through USB or Ethernet. Selectable grid pattern size and various colors and styles
are embedded. Corner Wall image adjustment for mapping image for 90 degrees corner and Linearity
Grid Line Adjustment are new function in geometry alignment. Separate RGB gamma correction for
edge blending region color fine-tune, individual color correction for each output, color uniformity
and 9 regions non-edge blending area black level uplift are also standard functions in the EdgePro.
Users can see real time geometry and color adjustment to get optimized results. HDMI loop out
supports daisy chain connection up to 4096x2160 @60Hz and allows large display with multiple
EdgePros cascaded. The video wall function in EdgePro is to crop and allocate source image for each
projector and set overlap pixels for edge blending. Complete curved edge blending can be achieved
through remote controller and Ethernet without PC software, video distributor and splitter. EdgePro
is designed to support programmable EDID and non-VESA standard input. User can create any EDID
timing in the range between 1024x768 and 3840x2400 in order to optimize video performance. Using
the EdgePro, users can replace high end projectors with low cost projector without lens shift, warp
and edge blending. It provides easy configuration, low entry barrier, cost effective, reliable and
flexible solution.

Page|9
www.avenview.com
3. Features
A. Input and output:
1 Input ports: 2x HDMI, 1xVGA, 1x DisplayPort。
•HDMI & DisplayPort support 4096*2160 @60Hz, 3840*2400 @60Hz with 4:4:4 sampling
without compression. VGA supports up to WUXGA or 205MHz analog input signal.
•Connect with various video sources and support none VESA standard input resolution.
2. Output ports: 2x HDMI. Selectable output resolutions: 720x480, XGA, WXGA, 1280x1024,
1366x768, 1400x1050, 1600x1200, 1920x1080 (24/30/50/60Hz), 2048x1080/60 &
1920*1200/60.
3. Loop out port: 1x HDMI (supports 4096*2160@60Hz & 3840x2400@60Hz)
4. Signal frame lock for synchronization between multiple output channels.
B. Image warp, geometry alignment and edge blending
1. Selectable grid pattern size for geometry alignment from 8-100 pixels in H&V with variable
color and styles. Default size is 32*32 pixels.
2. With full functions for quick 4 corner alignment, vertical and horizontal keystone correction,
Pincushion & Barrel adjustment, image warp and image 90/180/270 degrees rotation and flip.
3. Each unit controls dual projectors and can be cascaded to control unlimited number of
projectors.
4. Integrated with full function IR remote controller. Manual geometry alignment up to 9*5 grid
patterns with H=+_ 1200 pixels and V=+_1200 adjustment range in full HD output (4 corner +
warp adjustment).
5. Windows PC tool is available for warp and geometry alignment up to 17x17 grid patterns with
H=+_1200 pixels and V=+_1200 pixels adjustment range in full HD output through USB or
Ethernet. After finishing geometry alignment, the parameters can be stored inside EdgePro
and no more PC tool is needed.
6. Corner wall geometry alignment at 90 degrees corner wall up to 900 pixels adjustment range
in H&V directions with up to 1200 pixels position adjustment in horizontal direction.
7. Four directions edge blending up to H=1920, V=1200 overlapped pixels for flat, curved &
cylindrical screens.
8. Independent RGB gamma selection for edge blending color fine tune.
9. Precise black level uplift at multiple selected areas (up to 9) to compensate light leakage in the
projector.
10. White balance and individual color correction for each projector.
11. Fine pixel color uniformity adjustment across entire image.

Page|10
www.avenview.com
C. High end 10-bit video processor
1. Integrated with 10-bit high end processor with 3D motion adaptive de-interlace, low angle
smooth algorithm and 3:2/2:2 film mode detect and recovery function.
2. Complete color adjustment function, including brightness, contrast, hue, saturation, pre-set
color temperature, independent RGB color adjustment and white balance correction.
D. Edge mask
1 Image [SHIFT] to execute edge mask up to 500 pixels following the image after geometry
adjustment and Edge [Mask] with 8 adjustment points to provide irregular edge mask up to
900 pixels in each control point.
E. Video wall function
1. Image cropping and location assignment for each projector.
2. Overlap pixel adjustments up to 1800 pixels for image position shift, bezel compensation and
creating overlap region for edge blending and aspect ratio adjustment.
3. Connect with 4k/2k input signal and split the image for display devices without additional PC,
image splitter or other devices.
4. Serve as video wall controller for irregular video wall display up to 15x15 matrix display from
single signal input source.
F. Image rotation and flip
1 Image 90/270 degrees’ rotation & flip under 4k/30Hz input. Image 0/180 degrees’ rotation
and flip supports up to 4k/60Hz input.
G. System control and other features
1. 1U housing for easy rack installation. Professional design and reliable.
2. Operation temperature: 0-45〫C. Relative humidity: 10%-90% non-condensing.
3. Replace high price projector with low cost projector and achieve the same functionality.
4. Full function OSD by IR remote controller.
5. Full function system setup through USB, WebGUI or Ethernet (Including through WiFi by
Mobile or iPad)
6. Firmware update via USB or Ethernet.
7. Windows PC tool can control multiple processors simultaneously through USB or Ethernet.
8. Internal grid pattern with selective pixel size, color and style for easy geometry alignment.
9. RS232 & Ethernet system control compatible with most of control system.
10. User can select blue or black background color when no input signal is detected.
11. Programmable EDID in the range at H=1024~3840, V=720~2400.
12. BOX ID and programmable IP address for convenient multiple unit control at the same time.
13. User can save up to 5 settings and can be recalled by remote controller, RS232, USB or
network.

Page|11
www.avenview.com
14. Automatic power ON/OFF through input signal control. While no input signal is detected, it
will shut down output automatically.
15. Dual AC & DC Power supply systems. Provide DC 12V 1A output for signal extender while using
AC.
16. Dimension and weight: 440x190x45mm, 2.2kg (Body only)
4. Package Contents
1
The EdgePro Dual Channel Video Wall
Controller
X1
2
RC-400 IR Remote Controller with AAA battery
X1
3
IR Extending Receiver with 1.8m cable
X1
4
AC Main Power Cable
X1
5
User Guide
Avenview Website

Page|12
www.avenview.com
TECHNICAL
DESCRIPTION
Units
MLT-EdgePro-2X2E
UNIT DESCRIPTION
4K Edge blending Video wall processor
INPUT
2x HDMI 2.0b
1x DP1.2a
1x VGA
HDCP
HDMI V2.2/V1.4, DP: HDCP: V1.3
MAX. INPUT RESOLUTION:
HDMI & DP:4096*2160 @60Hz, 3840*2400 @60Hz with 4:4:4 sampling without compression
VGA: WUXGA or 205MHz analog input signal
OUTPUT
2x HDMI up to 2048x1080/60 & WUXGA
Selectable Output Resolution
720x480, XGA, WXGA, 1280x1024, 1366x768, 1400x1050, 1600x1200, 1920x1080
(24/30/50/60Hz), 2048x1080/60 & 1920*1200/60.
LOOP OUT
1x HDMI 2.0 for multiple unit cascade & daisy chain connections
(supports 4096*2160@60Hz & 3840x2400@60Hz)
MAXIMUM GEOMETRY
ADJUSTMENT
1200 pixels horizontal, 1200 pixels vertical
SUPPORT CORNER WALL
ADJUSTMENT
Yes: horizontal & vertical at same image scaling factor
SUPPORT LINEARITY GRID LINE
adjustments for quick horizontal & vertical line position alignment.
VIDEO WALL
Embedded full function video wall function for image split, cropping and overlap pixel setting.
video sources Timings
SUPPORT NON-VESA STANDARD INPUT TIMINGS
Settings Save
SETTINGS BACKUP AND SAVE
GRID CONTROL POINTS
17 X17
GRID PATTERN
Selectable grid pattern size from 8-100 pixels in H&V direction.
Default is 32*32 pixels.
Selectable grid pattern color and with optional transparency to see background image.
ASPECT RATIO ADJUSTMENT
Flexible aspect ratio adjustment in each edge up to+-1800 pixels
FREQUENCY
50Hz in/out & frame rate conversion.
PROCESSOR
10-bit processor, 3:2/2:2 cadence, low angle smooth algorithm, high quality scaling engine
3D
3D motion adaptive de-interlace
Frame lock for multiple channel synchronized outputs
HDR SUPPORT
SMPTE ST-2084, SMPTE ST-2086
Video Adjustments
•Individual color and white balance adjustment in each output channel.
•Individual 90/180/270 rotation, flip, cropping, scaling& color adjustment in each channel
•90/270 degrees rotation and flip only available under4k/30Hz input resolution
Audio
Embedded HDMI & SPDIF audio outputs
EDID
Selectable and programmable EDID
ESD Protection
±8kV (Air-gap discharge), ±4kV(Contact discharge)
Power supply
AC 100-240V
Power consumption
Max. 11w
Working environment
45〫C, 10-90% RH
Control
IR, RS232, USB, Ethernet
Dimensions
440mm*180mm*45mm,
Weight
2.2kg
Certified
CE/FCC/RoHS/Green
5. Specifications

Page|13
www.avenview.com
6. Basic operation & setting
6.1. Connecting the inputs
HDMI & DP input ports support up to 4096x2160 @60 Hz.
Only HDMI 2.0-1 input signal can be looped out. Loop out signal is unprocessed signal same as
HDMI 2.0-1 input signal. User can connect to next EdgePro for cascade application or as source
monitoring signal.
User can select from HDMI, DP and VGA input sources and display separate contents for two
projectors under below configuration: HDMI 2.0-1 (or HDMI 2.0-2) + DP, HDMI 2.0-1 (or
HDMI2.0-2) + VGA or DP + VGA. Please select source for CH-1, then second source for CH-2.
User can’t select two different HDMI input sources and display separately in two projectors.
6.2 Connecting the outputs
If the system uses only two projectors, user can connect any output to any projector and
select projector locations via [Video Wall]—[Pan] menu.
If multiple units of EdgePro are used and independent content display is required, user
needs to arrange the input source and output port connection and let input source be
displayed at desire projector.
Unprocessed signal
Loop out for cascade
HDMI Input
source
DP Input
source
VGA Input
source
CH-2 HDMI Output
Connector (Max. WUXGA)
Loop out for cascade or
input source monitoring
CH-1 HDMI Output
Connector (Max. WUXGA)

Page|14
www.avenview.com
Once input signal and output ports are properly connected, LED indicator on the front
panel will show up. If any of the LED in CH-1 & CH-2 is not showed up, please check the
input/output connection and cable.
LED lights up after proper input/output signals are active
6.3Input / Output selection & LED Indicators
If Power SW is on,
LED will light up
If Input Source is
detected, LED will light
If Output projector is
connected, LED will light up
•Select CH, then select input port and output resolution.
Each CH can select different input.
•
Output resolution will apply to two CH at the same time.
Press CH key to select
operation channel.

Page|15
www.avenview.com
Press CH-1/CH-2 button to select input port. Default input port is HDMI 2.0-1.
For one content edge blending display (all-in-one), user can select any input source in one
EdgePro application.
If multiple EdgePros are cascaded for edge blending, user needs to select HDMI-1 input source
and cascade to next unit through loop out port for big scale edge blending. If user wants to
select other signal sources for multiple unit cascade, user needs to add video distributor (or
splitter) in signal source and feeds the same signal to all EdgePro.
User needs to select source for CH-1 first, it will apply to both channels. Then select source for
CH-2 if CH-2 requires different source content.
If user wants to display independent content in each projector, user can select any two input
sources among HDMI, DP and VGA. User can’t select two HDMI input sources for independent
display in two projectors due to system limitation.
In multiple unit cascade system, user still can implement independent content display in each
projector through the selection of the input port for each output channel.
The output resolution selection will apply to both output channels at the same time. Default
output resolution for all channels is 1080p.
The output resolution should be the same as the projector native resolution to get the best
video quality. If user changes output resolution, geometry result will also be changed.
User can select output resolution through remote controller, USB or Ethernet.
Output resolution list: 720x480, XGA, WXGA, 1280x1024, 1366x768 ,1400x1050, 1600x1200,
1920x1080 (24/30/50/60Hz), 2048x1080/60 & 1920*1200/60。All output default resolution is
60Hz, RGB 4:4:4 and progressive. User can select 1080p 50 Hz to avoid frame repeat issue if the
input is 50Hz.
User can set EDID to have input source provide desired resolution. However, input resolution
is subjected to signal source and may not output desired resolution.
EdgePro can support non-VESA standard input timing once signal source can provide, such as
4096x2160, 3200x2400.
When press [OTH] key to select output resolution from remote controller, the monitor will
show the timing and take few seconds to finish the selection.
User can click [Info] key to get system information and see input / output signal resolution.
6.3.1 Input source selection
6.3.2 Output resolution selection

Page|16
www.avenview.com
LED indicators will show the input/output signal status.
Green LED will show up when the input signal is detected.
Orange LED will show up when the display device (projector) is detected.
If user presses Menu key for 5 seconds on the remote controller, EdgePro OSD menu will be
locked and the Power LED will be flashing. To press another 5 seconds, it will unlock OSD menu.
If multiple units are used in the system, user can set different ID and use remote controller [
85x ] key to execute independent control. Press [851] following other OSD keys, the remote
controller can only show Box ID #1 OSD and Power LED on front panel in other units will be
flashing. User can disable OSD LOCK with [850] command via IR controller.
Poor quality HDMI cable and signal source will affect the connection distance and may cause
signal noise or show intermittent image.
To ensure all cables are connected correctly, it is recommended to use locking cables.
Complete edge blending system should be connected to one power Distribution Box with
proper grounding. Power on the system after finishing all connections to avoid system damage
by floating voltage among devices.
When EdgePro is powered on, the booting time is about 19 seconds and the Input & Output
LEDs on front panel will stay “Lighted” all the time for the channel with correct input source
and output monitor connections.
If continuous flashing in some LED, it means the OSD function has been Locked. Please press
[Menu] key for 5 seconds to disable [OSD Locked] function. If system lock is done by remote
controller through [85x] operation, please press [850] to unlock system control.
6.3.3 LED indicators
6.4System connection and Power On

Page|17
www.avenview.com
Loop Out provides the same unprocessed source signal from HDMI2.0-1 input port.
HDMI 2.0-2, DP and VGA ports input source signal can’t be looped out. It can only be selected
in the same EdgePro. If user wants to execute multi-unit edge blending through DP or VGA input
ports, please add DP or VGA video distributor and feed signal to all EdgePro.
User can connect any Loop Out signal to any HDMI input port in the next EdgePro. No specific
HDMI input port is assigned.
User can connect up to more than 10 units of EdgePro through daisy chain connection. The
daisy chain connection number is related to the quality of HDMI cables and signal source
resolution—good cable or lower source resolution can connect more units. User can also add
HDMI splitter at the front end to increase daisy chain connection number for large scale video
display.
If loop out port is not connected, user can connect to a monitor for signal source monitoring
purpose. HDMI Loop Out port is for daisy chain connection. It is not an input port.
Box ID, RS232 and Ethernet settings can be executed through CH-1 or CH-2. The setting result
will be applied to both channels.
User can control or operate EdgePro settings through Ethernet. Default IP address is
192.168.0.100.
When multiple units are used at the same time, user can set different IP address in each
EdgePro so that each EdgePro can be controlled independently.
6.5HDMI Loop Out for daisy chain connection
HDMI Loop Out to next EDGEPRO HDMI input port or signal source
6.6System settings: Box ID, RS232, Ethernet

Page|18
www.avenview.com
The range of Box ID is 0 ~ 99 for RS2323 command.
If user uses remote controller to execute system operation, the Box ID range is 0 ~ 9.
RS232 is designed with DB-9 connector. User can select baud rate between 11520 and 9600.
We can provide UART protocol for the control from RS-232, USB, or Ethernet.
User needs to connect EdgePro to Wi-Fi Router or switch/hub through RJ45 to LAN port. Then
User can control the system through Ethernet.
Crossover UTP cable can be used for direct connection between PC and EdgePro. User needs to
set PC TCP/IPv4 with the same domain as EdgePro (for instance, to set IP address at
192.168.0.105) and subnet mask at 255.255.255.0).
Open web browser (Google Chrome or Internet Explorer) and input EdgePro IP address
(default IP address is 192.168.0.100), user can see EdgePro WebGUI and see virtual keys and
menu similar to OSD for further system operation. There is no additional software tool is
required.
If user can’t connect the network, please power off/on EdgePro again to let PC detect EdgePro
network system.
6.6.1 Box ID
6.6.2 RS232 settings
6.6.3 Ethernet

Page|19
www.avenview.com
Windows PC Tool is another web tool that has full function for system settings and operation.
It can also update Firmware or MCU code. Windowscan be downloaded from AVENVIEW
website.
Each EdgePro can set different IP address for independent operation and control.
Please use < > OSD keys to select OSD menu items and use ˄ ˅ OSD keys to change IP address.
If EdgePro is connected with WiFi Router (through LAN port), user can control EdgePro through
WiFi via PC, iPad or mobile phone.
If web server function is required, please contact us for further details.
IR remote controller has full functions for the operation of EdgePro.
IR receiver is on Front Panel. One 3.5ø mm audio connector for IR extender is located at Back
Panel of EdgePro. 1.8m IR extension cable is equipped in the packing. User can add audio
cable to extend the distance up to more than 20 meters.
IR remote control system is possible to be interfered and cause abnormal or discontinuous
operation. Under this condition, Ethernet operation may be the best choice.
6.7How to use IR Remote Controller
Crossover UTP cable

Page|20
www.avenview.com
[Scaling] under [Image Properties] menu is to select the display mode following either signal
source original aspect ratio or full screen display
For edge blending application, please set to [Full Screen] mode. Otherwise, there may be
abnormal display in some input timing.
Power on/off. If power off
by remote controller,
please power on by
Profile [Load] shortcut key
Channel selection
HDMI2.0-2 input port
HDMI2.0-1 input port
Work with other function
keys to execute function to
all channels at the same
time
Profile [Save] menu
System Information
OSD Menu operation
Input source selection
Output resolution selection
[4 Corner] geometry alignment
[Warp] curve geometry alignment
[Edge Blend] menu
[Video Wall] Menu
Grid pattern
Video Wall [Overlap]
System reset menu
6.8Full screen and native aspect ratio