Avenview Hbt-c6poe-hdv-s User manual

Control Your Video

VIDEO WALL VIDEO PROCESSORS

MULTIVIEWERS DIGITAL SIGNAGE

EXTENDERS CONTROL CENTERS

SCALERS WIRELESS

HDBaseT HDMI/VGA Scaler Over CAT5e/6/7

Transmitter with LAN Support

The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or

warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications

and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted

by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any

express or implied warranty, relating to its products are is strictly prohibited.

Model #: HBT-C6POE-HDV-S

Military Residential

Medical Aviation

Education Industrial

Corporate House Of Worship

www.avenview.com

Product Application & Market Sectors

www.avenview.com Page

TABLE OF CONTENTS

1. GETTING STARTED ..........................................................................................................................1

2. INTRODUCTION ........................... ..................................................................................................3

4. PACK AGE CONTENTS

.....................................................................................................................4

5. BEFORE INSTALLATION ................................................................................................................... 4

7.3 REMOTE CONTROL .....................................................................................................................8

8. RS-232 PIN DEFINITIONS ....................................................................................................................9

9. RS-232 COMMANDS..... .......................................................................................................................10

...........................................................................................................................................12

10. OSD MENU

11. INPUT RESOLUTION SUPPORT..........................................................................................................14

3. FEATURES ....................................... ...................................................................................................3

6. APPLICATION DIAGRAM ...................................................................................................................5

7. PANEL DESCRIPTION ...................................................................................................................6

7.1 INPUT PANEL (FRONT PANEL) .................................................................................................6

7.2 INPUT PANEL (REAR PANEL) .................................................................................................7

12. INSTALLATION ....................................................................................................................................15

13. GENERAL TROUBLESHOOTING .......................................................................................................15

14. SPECIFICATIONS .................................................................................................................................16

1.2 SAFETY INSTRUCTIONS ..................................................................................................................1

1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................... 2

1.1 IMPORTANT SAFEGUARDS ..............................................................................................................1

www.avenview.com Page

SECTION 1: GETTING STARTED

1.1 IMPORTANT

SAFEGUARDS

Please read all of these instructions carefully before you use the device. Save this manual for future reference.

What the warranty does not cover

•Any product, on which the serial number has been defaced, modified or removed.

•Damage, deterioration or malfunction resulting from:

•Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to

follow instructions supplied with the product.

•Repair or attempted repair by anyone not authorized by us.

•Any damage of the product due to shipment.

•Removal or installation of the product.

•External causes to the product, such as electric power fluctuation or failure.

•u se of supplies or parts not meeting our specifications.

•Normal wear and tear.

•Any other causes which does not relate to a product defect.

•Removal, installation, and set-up service charges.

1.2 SAFETY I NSTRUCTIONS

The HBT-C6POE-HDV-S has been tested for conformance to safety regulations and requirements, and has been certified

for international use. However, like all electronic equipments, the HBT-C6POE-HDV-S should be used with care. Read the

following safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.

! Do not dismantle the housing or modify the module.

! Dismantling the housing or modifying the module may result in electrical shock or burn.

! Refer all servicing to qualified service personnel.

! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage

or other hazards

! keep the module away from liquids.

! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on

to the housing, unplug the module immediately.

! Have the module checked by a qualified service engineer before using it again.

! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

www.avenview.com Page

1.3 REGULATORY N OTICES FEDERAL COMMUNICA

TIONS COMMISSION FCC)

This equipment has been tested and found to comply with part 15 of the f CC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.

Warning symbols Description

ONLY USE THE PROVIDED POWER CABLE OR

POWER ADAPTER SUPPLIED. DO NOT TAMPER WITH

THE ELECTRICAL PARTS. THIS MAY RESULT IN

ELECTRICAL SHOCK OR BURN.

DO NOT TAMPER WITH THE UNIT. DOING SO

WILL VOID THE WARRANTY AND CONTINUED

USE OF THE PRODUCT.

THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.

PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON

A SURFACE, IT SHOULD BE IN A GROUNDED

ENVIROMENT

www.avenview.com Page

2. INTRODUCTION

The HBT-C6POE-HDV-S is an HDBaseT™ Transmitter Scaler that supports both HDMI or PC (VGA) input. It is capable of

scaling and switching any video along with audio and extending the uncompressed digital signal over CAT5e/6/7 cable to the

Receiver at a distance of up to 100 meters. This unit can alsosupport 2-way IR, RS-232 and bidirectional LAN support. The

user can simply control many functions via on-panel buttons or IR remote control with support of an On-screen Display

(OSD) providing selection and system information. The HBT-C6POE-HDV-S provides a full range of output resolutions, from

640 up to 1080p and WUXGA (RB). The bi-directional Power over Ethernet (PoE) function provides greater flexibility during

installations.

• Supports both HDMI/VGA inputs scaling to a full range of HDTV or PC resolutions up to 1080p and WUXGA (RB).

• Transmission of uncompressed data over a single CAT5e/6/7 cable up to 100m/328ft.

• 5Play™ convergence: Video and Audio, LAN serving, bidirectional Power over Ethernet (PoE) and Control (IR RS-232 bypass).

• Supports IR, Remote control, RS-232 (bypass) and on-panel controls.

• Provides bidirectional 24V DC power to or receive from compatible PoE Receiver through CAT5e/6/7 cable.

• Supports Ethernet transmission rates up to 100 Mbps.

• Supports NTSC and PAL formats for Composite Video input.

Note:

1. This system was tested with CAT6/23AWG cables, results may vary with cables of different specifications.

2. The PoE function is designed for powering compatible Receiver units only—non-PoE Receivers will need their own power

supply. Receivers from other brands may not be compatible.

3. DO NOT connect the LAN connection to the CAT5e/6/7 port. Doing so may cause a power shutdown and may damage the

device.

3. FEATURES

www.avenview.com Page

4. PACKAGE CONTENTS

Before you start the installation of the HDMI HDBaseT Transmitter Scaler, please check the package contents.

1HBT-C6POE-HDV-S X 1

IR EXTENDER

IR BLASTER

POWER ADAPTER 24/1.25A

USER’S MANUAL

IR REMOTE

INPUT

EXIT MENU

RESET AUTO

ADJUST

www.avenview.com page 5

6. APPLICATION DIAGRAM

www.avenview.com Page

7. PANEL DESCRIPTION

7.1 INPUT PANEL (HBT-C6POE-HDV-S) Front Panel 7

1. SERVICE: Reserved for manufacturer use only. 2. IR RECEIVER WINDOW: Receives only the IR signal

from the supplied remote control for this device only.

3. HDMI: Connect to a digital source device such as Bluray

Set Top Box.

4. VGA: Connect to a Laptop/Desktop source with a

D-Sub 15 Pin cable.

5. AUDIO: Connect to an analog stereo (L/R) audio

source with a 3.5mm mini-jack cable.

6. MENU: This button enters the On-Screen Display

(OSD) menu.

INPUT (–) Button & HDMI/PC LED: Press the

INPUT (−) button to toggle between CV or PC inputs.

When in CV mode the LED will be lit, off when in PC mode.

7. −/+: Use these buttons to navigate down and up

in the on-screen menu.

ENTER: Press this button to confirm the selection. Also:-

Press this button together with [–] key to switch output timing to 720p@60 instantly.

Press this button together with [+] key to switch output timing to XGA (1024x768) instantly.

1234569

www.avenview.com Page

7.2 INPUT PANEL (HBT-C6POE-HDV-S) Back Panel

1. POWER LED: This LED will illuminate when the

device is connected to an active power supply.

2. DC 24V: Connect the 24 V DC power supply to the

unit and plug the adaptor into an AC outlet. Only one

unit requires powering if both the Transmitter and

Receiver are both PoE compatible.

3. RS-232 IN: Connect to a PC or RS-232 control system

with a D-Sub 9 pin male cable for the transmission of

RS-232 commands.

LAN: Connect to an active network for LAN serving. When

any compatible LAN equipped receivers are connected, this

allows the network access (including internet access if

available) to be shared between any

connected LAN

equipped receivers 100Mbps. Connect any Ethernet

equipped device e.g. a Smart TV or games console to the

LAN port of a receiver for that device

to share the network/

internet access.

23 4 5 6 7

5. IR Blaster: Connect the supplied IR Blaster cable for IR

signal transmission. Place the IR Blaster in direct line-of-

sight of the equipment to be controlled.

6. IR Extender: Connect the supplied IR Receiver cables

for IR signal reception. Ensure that remote being used is

within the direct lineof-sight of the IR Extender.

7. CAT5e/6/7 OUT: Connect to the Receiver unit with a single CAT5e/6/7 cable for transmission of all data signals.

MODE LED: This LED will illuminate when the power is connected.

LINK LED: This LED will illuminate when connected to a Receiver unit

that is connected with a TV/monitor that is displaying the signal.

PANEL DESCRIPTION

7.3 REMOTE CONTROL

www.avenview.com Page 8

1INPUT: Press this button to toggle between the HDMI or PC input.

2EXIT: Press this button to exit the menu or the current selection in the

on-screen menu.

3MENU: Press this button to enter into the OSD menu.

4RESET: Press this button to return the device to the factory default settings.

5AUTO ADJUST: Press this button tooptimize the positioning of the picture

(picture centering) on the screen.

6 OK & ▲▼◄►: Press 'OK' to confirm the selection or use the directional

buttons to navigate the on-screen menus.

7.4 IR Cable Pin Assignment

Power

IR Blaster Signal

IR Signal

Power

Ground

IR Extender

IR Blaster

INPUT

EXIT MENU

RESET AUTO

ADJUST

PIN DEFINE TX / RX

1N/C

2TxD/RxD

3RxD/TxD

4NC

5GND

6NC

7NC

8NC

9NC

8. RS-232 PIN DEFINITIONS

www.avenview.com Page 9

RS-232 SETTINGS

Baud Rate: 9600bps

Data Bit: 8 bits parity:

None

Flow Control: None

Stop Bit: 1

COMMAND DESCRIPTION

S SOURCE 1~2 1=PC

2=HDMI

R SOURCE Reports the numerical equivalent for the

SOURCE setting (as listed above)

S OUTPUT 0~25 12=1600×1200

0=Native

1=640×480

2=800×600

3=1024×76

5=1360×768

6=1280×720

7=1280×800

8=1280×1024

9=1440×900

10=1400×1050

11=1680×1050

13=1920×1080

16=1920×1200

17=480p

18=720p@60

19=1080p@60

20=1080i@60

22=576p

23=720p@50

24=1080p@50

25=1080i@50

R OUTPUT Reports the numerical equivalent for the

OUTPUT setting (as listed above)

S SIZE 0~6 0=OVERSCAN 4=LETTER BOX

1=FULL 5=UNDER 2

2=BEST FIT 6=UNDER 1

R SIZE

3=PAN SCAN

Reports the numerical equivalent for the SIZE setting

(as listed above)

Sets the numerical value for the CONTRAST

setting (0~60)

S CONTRAST 0~60

R CONTRAST Reports the numerical value for the CONTRAST

setting (0~60)

Sets the numerical value for the BRIGHTNESS

setting (0~60)

S BRIGHTNESS 0~60

R BRIGHTNESS Reports the numerical value for the BRIGHTNESS

setting (0~60)

9. RS-232 COMMANDS

www.avenview.com Page 10

COMMAND DESCRIPTION

S HUE 0~60 Sets the numerical value for the HUE setting

(0~60)

R HUE Reports the numerical value for the HUE setting

Sets the numerical value for the SATURATION

setting (0~60)

S SATURATION 0~60

R SATURATION Reportsthe numerical value for the SATURATION

setting (0~60)

Sets the numerical value for SHARPNESS setting

(0~30)

S SHARPNESS 0~30

R SHARPNESS Reports the numerical value for the SHARPNESS

setting (0~30)

S NR 0~3 0=OFF 2=MIDDLE

1=LOW 3=HIGH

R NR Reports the numerical equivalent for the NOISE

REDUCTION setting (as listed above)

S AUDIO DELAY 0~3 0=OFF 2=110ms

1=40ms 3=150ms

R AUDIO DELAY Reports the numerical equivalent for the AUDIO

DELAY setting (as listed above)

S AUDIO MUTE 0/1

R AUDIO MUTE

0=ON 1=MUTE

Reports the numerical equivalent for the AUDIO

MUTE setting (as listed above)

FW Checks the FIRMWARE version

S RESET 1 Sets the numerical equivalent for the RESET

setting (as left)

Note:

1. RS-232 commands will not execute unless followed by a carriage

return and LF (Line Feed).

2. Commands are not case-sensitive.

3. Resolutions 1~16 are RGB encoded and 17~25 are YUV encoded.

www.avenview.com Page 11

0=ENABLE 1=DISABLE

S KEY LOCK 0/1

R KEY LOCK Reports the numeric equivalent for the KEY

LOCK setting (as listed above)

S AUTOSCAN 0/1 0=DISABLE 1=ENABLE

R AUTOSCAN Reports the numeric equivalent for AUTO SCAN setting

(as above)

1ST LAYER 2ND LAYER 3RD LAYER 4TH LAYER

DISPLAY OUTPUT Native

640x480 60

800x600 60

1024x768 60

1360x768 60

1280x720 60

1280x800 60

1280x1024 60

1440x900 60

1400x1050 60

1680x1050 60

1600x1200 60

1920x1080 60

1920x1200 60

720x480P 60

1280x720P 60

1920x1080I 60

1920x1080P 60

720x576P 50

1280x720P 50

1920x1080I 50

1920x1080P 50

SIZE SIZE OVER SCAN

FULL

ASPECT RATIO

PAN SCAN

LETTER BOX

UNDER 2

UNDER 1

10. OSD MENU

www.avenview.com Page 12

1ST LAYER 2ND LAYER 3RD LAYER 4TH LAYER

SIZE MODE INFO INFO

OFF

PC (PC mode only) AUTO SETUP NO

YES

H_POSITION 0~60 (30)

V_POSITION 0~60 (30)

PHASE

CLOCK

WXGA/XGA XGA

WXGA

RESET NO

YES

COLOR COLOR

R OFFSET

G OFFSET

B OFFSET

CONTRAST 0~60

BRIGHTNESS 0~60

HUE 0~60

SATURATION 0~60

SHARPNESS 0~60

NR. OFF

LOW

MIDDLE

HIGH

www.avenview.com Page 13

1ST LAYER 2ND LAYER 3RD LAYER 4TH LAYER

AUDIO VOLUME 0~100

DELAY OFF

40ms

110ms

150ms

SOUND ON

MUTE

SETUP FACTORY RESET NO

YES

KEY LOCK OFF

INFORMATION INPUT

OUTPUT

REVISION

11.Input Resolutions Support

INPUT RESOLUTION HDMI PC

NTSC/PAL



VGA@60/72/75 Hz



SVGA@56/60/72/75 Hz 

XGA@60/70/75 Hz 

SXGA@60/75 Hz 

UXGA@60 Hz 

1280×800@60 Hz 

1680×1050@60 Hz (RB) 

1920×1080@60 Hz 

www.avenview.com Page 14

Note: Items in Bold are the default settings.

480i/576i

480p/576p

720p@50/60 Hz

1080i@50/60 Hz

1080p@50/60 Hz



www.avenview.com Page

12. INSTALLATION (HBT-C6POE-HDV-S)

To setup Avenview HBT-C6POE-HDV-S please follow these steps for connecting to a device:

1. power off all sources such as media player, set-top box, pC etc;

2. Connect both HDMI/VGA video Source to the HDMI & VGA INpuT of (HBT-C6POE-HDV-S);

3. Connect HBT-C6POE-HDV-S to HBT-C6POE-R with a CAT5e/6 at the CAT5e/6 OUT;

4. Connect HBT-C6POE-R to TV/Monitor with HDMI Cable;

5. plug in 24V/2.7A DC power adapter to power jack of HBT-C6POE-HDV-S;

6. power on HDMI & VGA Source and TV/MONITOR;

7. When the Input is connected and powered on the corresponding POWER lED will light .

13. GENERAL TROUBLESHOOTING

PROBLEM POSSIBLE SOLUTION

NO IMAGE

•Check if connection to the source and the display are correct.

•Ensure that display device supports resolution from 640 up to 1080p.

•

•Check Power lED , MODE and Link lights on the CAT5E/6 connector

MODE LED: This LED will illuminate when the power is connected.

LINK LED: This LED will illuminate when connected to a Receiver unit that is connected

with a TV/monitor that is displaying the video and audio signal.

•Check INPUT (–) Button & HDMI/PC LED: Press the INPUT (−) button to toggle

between HDMI or PC inputs. When in HDMI mode the LED will be Red,

LED Green when in PC mode. (Section 3 panel Description)

please use the supplied power supply-24V DC

www.avenview.com Page

14.SPECIFICATIONS

Item Description

UNITS HBT-C6POE-HDV-S

UNIT DESCRIPTION HDBaseT™ Transmitter Scaler

OUTPUT BANDWIDTH 300MHz / 10.2Gbps

HDMI RESOLUTION SUPPORT 480i~1080p

VGA RESOLUTION SUPPORT VGA~WUXGA (RB)

CAT5 RESOLUTION SUPPORT HD: Up to 1080p@60 Hz / PC: Up to WUXGA (RB)

IR FREQUENCY 30~50 kHz

INPUT

1×HDMI, 1×VGA, 1×3.5mm, Mini-jack (L/R), 1×RS-232,

1×LAN,

1×IR Extender

OUTPUT 1×CAT5e/6/7, 1×IR Blaster

DIMENSIONS (WxDxH) 7.9" x 5.7" x 1.2" (Jacks Included)

NET WEIGHT 1.33lbs

POWER SUPPLY 24V/2.7A DC / 110-240V

POWER CONSUMPTION 17W

ESD PROTECTION 1 x HDMI Type A (19 pin female)

Environmental

OPERATING TEMPERATURE 32˚ ~ 104˚F (0˚ to 40˚C)

STORAGE TEMPERATURE -4˚ ~ 140˚F (-20˚ ~ 60˚C)

RELATIVE HUMIDITY 20~90% RH (non-condensing)

www.avenview.com

Avenview Warranty Certificate

AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used

normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s

published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.

LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance

and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,

please contact s[email protected].

PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if

the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact

[email protected].

To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented

to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must

be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight

charges and brokerages when shipping the product(s) to the receiver.

NOT COVERED BY THIS WARRANTY

This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including

but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,

earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service

performed by anyone who is not a representative of Avenview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the

normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).

AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR

CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR

ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;

LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT

OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.

Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or