Avenview SDI-SPLITPRO-4S User manual

Advanced SDI Quad Screen Multiviewer
3827.
© 2012 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims
any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular
purpose, or infringement of any intellectual property right. Reproduction of this manual, or parts thereof, in any form, without the express written
permission of Avenview Inc. is strictly prohibited.
Model #: SDI-SPLITPRO-4S

Page|2
www.avenview.com
TABLE OF CONTENTS
SECTION 1: GETTING STARTED........................................................................................................ 3
1.1 IMPORTANT SAFEGUARDS ................................................................................................ 3
1.2 SAFETY INSTRUCTIONS ..................................................................................................... 3
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) .......... 4
2. INTRODUCTION ................................................................................................................. 5
3. PACKAGE CONTENTS........................................................................................................ 6
4. BEFORE INSTALLATION ..................................................................................................... 6
5. PANEL DESCRIPTION.......................................................................................................... 7
6. SDI-SPLITPRO-4S I/O CONNECTORS................................................................................ 8
7. INSTALLATION .................................................................................................................... 9
8. INSTALLATION .................................................................................................................... 9
9. SOFTWARE SETUP GUIDE................................................................................................ 10
10. SPECIFICATIONS................................................................................................................ 14
11. GENERAL TROUBLESHOOTING...................................................................................... 15

Page|3
www.avenview.com
SECTION 1: GETTING STARTED
1.1 IMPORTANT SAFEGUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
1.2 SAFETY INSTRUCTIONS
The Avenview SDI-SPLITPRO-4S Advanced Quad Screen Video Processor has been tested for conformance to
safety regulations and requirements, and has been certified for international use. However, like all electronic
equipment’s, the SDI-SPLITPRO-4S should be used with care. Read the following safety instructions to protect
yourself from possible injury and to minimize the risk of damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls
or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.

Page|4
www.avenview.com
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols
Description
ONLY USE THE PROVIDED POWER CABLE OR
POWER ADAPTER SUPPLIED. DO NOT TAMPER
WITH THE ELECTRICAL PARTS. THIS MAY
RESULT IN ELECTRICAL SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO
WILL VOID THE WARRANTY AND CONTINUED
USE OF THE PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO
STATIC. PLEASE ENSURE IF RACK MOUNTED OR
INSTALLED ON A SURFACE, IT SHOULD BE IN A
GROUNDED ENVIROMENT.

Page|5
www.avenview.com
2. INTRODUCTION
The SDI-SPLITPRO-4S Advanced 3G/HD/SD-SDI Quad-view Video Processor is an advanced video processor
for multimedia presentations and ideal for surveillance applications. This unit is an ideal solution for applications
where four video signals must be displayed on a single display. It supports up to 4 SDI video inputs, which can be
outputted simultaneously with the desired display layout through software control. The advanced video
processor allows you to manipulate the output images to various sizes and multiple positions on the desired
display. This unit can controlled with the ease of the RS232 via a cable or control system, this functionality allow
the user to easily set the desired outputs by 5 preset layouts or 8 custom layouts saved by the user.
The embedded scalar converts signals from input sources to match the native resolution of monitors, flat panel
displays, projectors as well as user-selectable output settings up to WUXGA (1920x1200). Dual outputs are
provided in both digital (SDI) and digital (DVI) or (DVI/HDMI) format, one is connected to remote display and the
other is connected to on-site display for real time monitoring.
-Supports 3G/HD/SD SDI video formats
-Input resolutions support interlaced or progressive video under SMPTE.
-Dual outputs DVI(640x480 to 1920x1200) / SDI(720P, 1080P)
-Each SDI channel has 1 re-clocked SDI loop-outs.
-Adjustable size& position through software.
-Image parameters and layouts are automatically saved in flash memory and can be recalled for
future use.
-User-selectable output settings, up to 1920x1200(Only for DVI).
-Perfectly as a video screen splitter, a video converter and a video switcher.
-Firmware upgradable for support of new features and technology enhancements.
-Software control through RS-232.
-Control protocol available for customer proprietary design
-1U size.

Page|6
www.avenview.com
3. PACKAGE CONTENTS
Before you start the installation of the converter, please check the package contents.
1
SDI-SPLITPRO-4S
1
Rack Mounting Kit
1U rack mounting ear
1
RS232 to USB Adapter
1
Software CD
1
12V Power Brick
1
AC Power Cord
1
User’s Manual
4. BEFORE INSTALLATION
Put the product in an even and stable location. If the product falls down or drops, it may cause an injury
or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may
cause a fire.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.

Page|7
www.avenview.com
5. PANEL DESCRIPTION
Avenview Quad Screen Video Processor (SDI-SPLITPRO-4S) has 4 inputs, 2 Main outputs, 4 SDI Local Loop out
to local monitors as well as DVI output accepts both graphics and video signals, which come from SDI, composite
video sources respectively.
INPUT PANEL (SDI-SPLITPRO-4S) Front
1. Power indicator
INPUT PANEL (SDI-SPLITPRO-4S) Rear
2. Power Switch: On/OFF
3. RS-232: To Send Serial Commands
4. Power Supply: 12V DC
5. Dip Switch: Factory Reset
6. Device ID: To identify between units
7. USB: Firmware Update
8. Ethernet: To connect via IP
9. Outputs: 2 x SDI Outputs
10.Outputs: DVI Output
11. Inputs: 4 x SDI inputs
12. Loop Out: 4 x SDI Local Loop out

Page|8
www.avenview.com
6. SDI-SPLITPRO-4S I/O CONNECTORS
CONNECTORS
VIDEO SOURCE
INPUT
SDI
SDI
CVBS
OUTPUT
DUAL
SDI/DVI-D OUT
Display
1 x DVI/HDMI Display [165MHz]
2 x SDI
4 x SDI LOCAL LOOP with Re-Clocking

Page|9
www.avenview.com
7. INSTALLATION
To setup Avenview SDI-SPLITPRO-4S follow these steps for connecting to a device:
1. Mount or fix the SDI-SPLITPRO-4S safely
2. Switch off SDI-SPLITPRO-4S and all source devices and displays that will be connected
3. Connect a monitor, projector and any HD displays that come with DVI / HDMI inputs by using 1 male –
male DVI cable to SDI-SPLITPRO-4S DVI output. (you can connect 2 displays equipped with DVI and
SDI.
4. Connect FOUR (4) devices equipped with SDI output (such as broadcast camera) which can output
3G/HD/SD video signals to the BNC input connectors to the SDI connector on the rear of the unit.
5. Connect your computer to SDI-SPLITPRO-4S via RS232 cable and then install the software
6. Turn ON SDI-SPLITPRO-4S
7. Run the Control Software and establish the connection between PC and SDI-SPLITPRO-4S
8. Turn ON all connected devices and then control the display output thru RS232 and included software
8. INSTALLATION
1. The SDI-SPLITPRO-4S provides a software control program which runs under Microsoft Windows 98,
2000, XP, Vista, 7 through the interface of RS-232 serial control.
2. Before you click on the icon of the software, make sure you have secured the connection between your
computer COM port and the SDI-SPLITPRO-4S.
3. Install driver for RS232 to USB adapter
4. Once SDI-SPLITPRO-4S is turned on, it display green LED light
Ensure that correct driver for RS232-USB Adapter (included with SDI-SPLITPRO-4S/K) is
installed.
You can check “Device Manger” under “Ports” page to check if drivers are installed
correctly.

Page|10
www.avenview.com
9. SOFTWARE SETUP GUIDE
1. Power up the SDI-SPLITPRO-4S and you can see VFD on the front panel blink. .
2. Launch Avenview Control Software. It will open following “Serial Port” setting page.
3. Click on Scan button and it will automatically detect Avenview Video Processor and display the following
screen:
4. Note the “Device – ID” and Select Correct “Com Port” and Device ID” from bottom of screen. Once
Correct “Com Port” and “Device ID” is selected, it will change “Device Modular Error” to “Device
Ready” as shown below:

Page|11
www.avenview.com
5. Once Device is Ready, click “OK” and Avenview Control Software will launch
.

Page|12
www.avenview.com
MAIN Input Panel
This window displays the inputs Size and position on the desired output monitor.
Toolbar Icons
1. CPU ICON- retrieves the data from the device and updates the software state.
2. RS-232 ICON- Opens the RS-232 settings window.
3. SAVE ICON-Opens the Custom Layout Setting Window
OUTPUT RESOLUTION
SUPPORTED MODE
RESOLUTION
SUPPORTED MODE
RESOLUTION
HDTV 1080p
1920x1080@60Hz (SDI)
VESA
1280x1024 @ 60Hz
VESA
1680x1050@60Hz
VESA
1280x960 @ 60Hz
VESA
1600x1200 @ 60Hz
VESA
1280x768 @ 60Hz
VESA
1440x900 @ 60Hz
HDTV 720p
1280x720 @ 60Hz (SDI)
VESA
1366x768 @ 60Hz
VESA
1024x768 @ 60Hz
Main Panel Setting
1. Control Percent 10-100%-This percentage control allows the user to control the
window size of the Main Panel to view all the inputs easily.
2. PAP Layout Display –opens the PAP Layout Display Window
3. Lock Aspect Ratio- Fix the size ratio when the window is resizing.
PAP Mode Control/Input Selection
1. Main Window: The user can set the visible, position, size, polarity
and default layout.
2. Input Selection: Set the window to what input.
3. Window Polarity: Set the main window layer polarity in “PAP Mode”.
1
3
4
2
5

Page|13
www.avenview.com
4. Window Visible: Set the window visible in “PAP Mode”.
5. Window Position and Size: Set the window
position and size in “PAP Mode”.
FULL SCREEN /PAP MODE
1. Full Screen: Set the MAIN window to Full Screen.
Set Window 1 Full Screen
Set Window 2 Full Screen
Set Window 3 Full Screen
Set Window 4 Full Screen
2. PAP Mode: Set to last PAP layout.
3. Default Layout: The user can set the layout on the Monitor by selecting the Five (5) preset
layout defined in the device.
Panel Cross
*Panel Right –Type
*Panel Left –Type
* Panel Top –Type
*Panel Bottom - Type
NOTE: THE “MAIN WINDOW” WILL BE THE LARGEST SIZE IN THE ICON.
4. Custom Layout- The user can create their own layout and design of by selecting the EIGHT
(8) Custom Layout Tabs ………………. . These layouts can be save by
selecting the SAVE ICON in the Toolbar List
6

Page|14
www.avenview.com
10. SPECIFICATIONS
MODEL
SDI-SPLITPRO-4S
DESCRIPTION
Advanced Quad Screen Video Processor with Front Panel and IR Control
DUAL OUTPUT SUPPORT
Yes [DVI & SDI]
BACKGROUND VIDEO INPUT
No
HDCP COMPLIANCE
Yes
VIDEO BANDWIDTH
DVI/HDMI[165MHz]
SDI 3G/HD/SD
SUPPORTED RESOLUTIONS
480i / 576i/ 720p / 1080i / 1080p
AUDIO SUPPORT
No
CONTROL
RS232 / Ethernet
EMBEDDED VIDEO MIXER
Yes
ABILITY TO CASCADE
No
INPUT TMDS SIGNAL
1.2 Volts (peak –peak)
ESD PROTECTION
Human body model - ± 15kV (air gap discharge) & ±8kV (contact discharge
4x SDI
1 x RS232
1 x RS485
OUTPUT
1 x DVI (Also supports HDMI signal by DVI to HDMI Cable)
2 x SDI
DVI CONNECTOR TYPE
DVI-I (29-Pin female)
BNC CONNECTOR
75inter-locked socket
RS232 CONNECTOR
DE-9 (9-pin D-sub female)
RCA CONNECTOR
75Ω
RJ45 CONNECTOR
WE/SS 8P8C with 2 LED indicators
DIMENSIONS
11.8" x 15.3" x 1.7" (L x W x H)
SIZE
1U Rack-mount with ears
POWER SUPPLY
AC 100-240V
POWER CONSUMPTION
35 Watts (max)
OPERATING TEMPERATURE
0~40°C [32~104°F]
STORAGE TEMPERATURE
-20~60°C [-4~140°F]
RELATIVE HUMIDITY
20~90% RH [no condensation]

Page|15
www.avenview.com
11. GENERAL TROUBLESHOOTING
PROBLEM
POSSIBLE SOLUTION
NO POWER
Ensure that SDI-SPLITPRO-4S is plugged in
If you are recovering from power outage, accidentally unplug the adapter or
other power surge conditions, leave the device off for an at least a minute
and then power it on again.
NO OR DISTORTED
IMAGE
Make sure all cables are in good working condition and properly connected
to the SDI-SPLITPRO-4S and displays.
Configure the output video resolution so that it doesn’t excess the native
resolution of the display. ( in this case, the message of “out of range” is
usually showed on your screen)
POOR QUALITY
We suggest that don’t use T-connectors to split your video source into to
images displayed on two different screens. That will lower output video
quality. Use a distribution amplifier instead of T-connectors.
Make sure the video source is not compressed and maintains the highest
native resolution.
WRONG COLOR
Press “Color Balance” key for auto configuration.
Auto color configuration only works at VGA and Component inputs.
NO VIDEO AFTER
FACTORY
HARDWARE AND
SOFTWARE
RESET
Always perform a hard power reset from the back of the unit using the
power switch on back right.
In the configuration software after the factory reset navigate to:
Advance setting button
Ensure the correct COM Port is enabled
Wait until Green check mark and Device Ready! is complete
Proceed to “Device Setting/Testing” “Execute Selector”
Select “Modular Configure”then Press Execute Button

Page|16
www.avenview.com
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation
or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview
concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits,
or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the Avenview hardware,
software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.