Avermedia AVerDiGi EH5116 Pro Operator's manual

AVerMedia®
AverDiGi EH5116 PRO
Quick Installation Guide

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT
PRIOR NOTICE
i
THE INFORMATION CONTAINED HEREIN IS TO BE
CONSIDERED FOR REFERENCE ONLY
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT
MODIFICATION
Copyright ©2008
AVerMedia INFORMATION, Inc
All rights reserved
Reproduction without permission is prohibited

Package Contents
(1) (2)
(3)
AVerMedia
AVerDiGiEH5116
®
QuickInstallationGuide
(4) (5) (6)
(7)
(8)
i
If there is any damage, shortage or inappropriate item in the package
contents, please contact with local dealer
(1) EH5116 PRO unit
(2) Remote Control (Batteries are
included)
(3) Quick Installation Guide
(4) Power Cord (*The power cord may
vary according to the local
electricity system.)
(5) Audio cable (16CH audio out, 1CH
audio in, 1CH microphone in)
(6) Software CD (Manual is included)
(7) 12 * screws for internal HDD
installation
(8) SATA cable
1

Hardware Installation
A. Install the hard disk
Follow the steps to install the hard disk:
i
For hard disk spec, please referring to
http://www.avermedia.com/AVerDiGi/Product/ →Embedded Hybrid
DVR/NVR →AVerDiGi EH5116 →Hardware Recommendations
Follow the illustrated instructions below to install the hard disk:
1. Unlock the removable hard disk
drawer
2. Open the removable hard disk
drawer
3. And then, pull out the removable
hard disk drawer 4. Remove the removable hard disk
drawer cover
2

5. Carefully insert the hard disk in
the removable rack 6. Turn the removable hard disk
drawer over and screw hard disk
with screws
7. And then, close the removable
hard disk drawer cover
8. Slide the drawer back
9. Lock the removable hard disk
drawer keylock
10. Power on the removable hard disk
drawer
11. You may now connect all the cables and power on the DVR unit.
i
Please make sure the power of removable hard disk is on before starting DVR
unit to avoid hard disk detection error.
3

B. After the hard disk installation, please connect the cables and
power as the illustration showed
i
– DVR unit can connect 16 cameras in analog and IP cameras combo.
– DVR unit doesn’t supply the power to connected external device.
– Each time you change the video display output, the power must be
turned off and switch the video display output, and then turn on the
DVR unit.
– Pen drive and external hard d sk must be FAT32 format.i
4

Using DVR System
A、Way to Operate DVR
There are three ways can be managed the DVR unit:
1. Using mouse and keyboard
Connecting the mouse and keyboard through USB interface, user can
easily to management the DVR unit. For the first time using DVR unit,
mouse and keyboard is the best way to set up all DVR relevant
configurations.
2. Using Remote Controller
After DVR unit has been setup, user can use remote control to preview,
playback, backup, reset alarm, output video and so on functions.
3. Using Front Panel button
It’s an optional way to operate DVR unit. Front panel button function acts
as same as remote controller.
i
For the first time using DVR unit, using mouse and keyboard to setup all
configurations.
B、First Time Using DVR Unit
1. Connect the mouse and keyboard to DVR unit(through USB interface)
2. Select the video output – VGA, TV-NTSC, or TV-PAL
i
VGA: DVR output the video to a LCD monitor or a CRT monitor
TV-NTSC: DVR output the video to a TV and video system is NTSC
TV-PAL: DVR output the video to a TV and video system is PAL
3. Power on the DVR unit.
4. For security purpose, the DVR system would require you to enter User ID
and Password before it can be accessed. When the Authorization dialog
box appears, select the ID (superuser or user) and enter the Password.
(Superuser and user default password both are 111111).
i
Superuser has full authority to configure and operate DVR system.
5

After login, the main GUI as following shown:
5. The hard disk must be formatted before user can use it with DVR unit.
Following the below steps to format the hard disk.
a. Click
Setup and enter the password
b. Click
System →Add
c. Select the hard disk from device list and select Format type
d. Click
Format button to start formatting
e. When formatting is done, click OK.
6. Setup the date and time in order to have correct recording time and date.
Following the below steps to setup date and time:
a. Click
Setup and enter the password
b. Click
System
c. In
Time section, click Setting button of System Time.
d. Select the date and adjust the time, and then, click OK.
7. Connecting the camera.
To connect analog camera:
a. Plug the analog camera audio cable into DVR unit.
b. Click
Setup and enter the password
c. Click
Camera
d. Select camera channel and type of camera – Analog Camera
e. And then, enable the camera
f. Give a name of camera and enter shot description.
g. Adjust the bright, contrast, hue, and saturation of camera
h. Click
OK
6