Avers Screens Solar Pro User manual

Electric projection screen
Avers Solar Pro
User’s manual
Read these instructions carefully before operating the screen.

Table of contents:
1. Safety rules
1.1. Declaration of Conformity CE
2. Product specification
2.1. Contents of package
2.2. Technical data
3. Screen installation
3.1. Installation directions
3.2. Ceiling installation
3.3. Electric installation
3.4. Screen programming
4. Screen operation
4.1 Manual operation
4.2 Screen maintenance
4.3 Before asking for service
5. Warranty conditions
2
Thank you very much for the purchase of our product. The manual booklet contains all operation information
you may require to install properly and operate the screen. We hope it will help you to get the most performance and
enjoyment of your new screen. Enjoy time with the Avers Screens product.
SAFETY INFORMATION
NOTICE: Important safety information.
Follow the instructions described in the operating manual for safety reasons. After reading the manual, please store
it in a safe place just in case you need it in the future.
NOTICE: THE DEVICE HAVE TO BE EARTHED.
WARNING:
1) Disconnect the device from the power supply if it will not be used within longer period of time.
2) Do not open the casing of the device in order to avoid possible electric shock. There are not any user operated
parts inside the case of the screen. All service work can be done by Avers Authorized Service Center personnel
only.
3) Do not remove the Ground pin from the power outlet neither connect the device to the socket without the Ground
pin. If you can't put the plug to the power outlet, please ask electrician for assistance.
Dear Customer,

1. SAFETY RULES
SAFETY INFORMATION
NOTICE: Important safety information. It is important for the safety of persons to follow these instructions.
After reading the manual, please save it just in case of need in the future
ź Do not allow children to play with the fixed controls (remote control).
ź Keep the remote control unit out of reach of children.
ź Frequently examine the screen installation for imbalance and signs of wear or damage to cables. Do not use if repair or
adjustment is necessary.
ź Watch the moving screen and keep the people away until the screen is completely rolled in/out. It will help to avoid
injuries caused with moving screen.
ź Do not attach any objects to the screen’s bottom bar. Screen damage and/or person injury danger.
ź All installation work should be carried out by the qualified technician.
ź Improper installation of the screen can cause device damage or health breakdown.
ź Ceiling/wall installation can be done with the originally supplied mounting brackets dedicated for this model only.
ź Do not do anything that may damage the power cable or power plug.
ź Do not damage the power cable: make any modifications by your own, put it near the hot objects, bend it strongly,
twist it, pull out the power cable, put the heavy objects on the cable, wrap it into the bundle.
ź Operation of the screen with damaged power cord can result with electric shock, electric short circuit and fire.
ź Do not touch the power cable and the power plug with wet hands.
ź Always follow the instructions described in the operating manual.
1.1. Declaration of Conformity CE
3
Under it’s own responsibility declares:
Projection screens series : Stratus 2, Stratus 2 Tension, Akustratus 2, Akustratus 2 Tension, Cumulus X,
Cumulus X Tension, Solar, Solar Prof., Solar Prof. Rental, Solaris, Solaris Tension, Contour,
The above mentioned products are in conformity with the following norms harmonized with the directives:
PN-EN 55014-1:2012
PN-EN 60335-1:2015
PN-EN 61000-3-2:2014
PN-EN 61000-3-3:2013
PN-EN 60335-2-97:2007
Manufacturer’s Declaration of Conformity CE No. 2E/2017
Paweł Zieliński
Pruszków 2017.10.02
All screens and accessories mentioned below are manufactured in Poland according to the essential
safety requirements of the Council Directives: Safety Directive 2001/95/WE with further updates,
EMC Directive 214/35/EC and LVD Directive 2014/30/EC
Avers Screens Sp. z o.o.
Al. Jerozolimskie 424A
05-800 Pruszków, Poland
Contour Tension, Cirrus S, Nimbus
Projector brackets: Alumount, Promount, SimpleMount, Shortmount, Simlift
Projector lifts: Simlift, Simlift XL, Simlift HC
Remote control system series: ALFA (IR, Radio, Trigger i Trigger Wireless), BETA, +DELTA

2. Product specification
Electrically rolled projection screen designed for fixed installation at projection systems for business presentations
and/or home cinema applications. Screen case made with aluminium alloy, decorative element at the bottom bar available
optionally in colors: white, yellow, blue, green, brown, grey or black. Best picture quality can be reached when the
selection of the type of projection surface and size will be optimal for the, projection device (projector) and projection
conditions at the planed installation place. Built-in radio frequency remote or triggered control systems (factory installable
options) allows comfortable automatic operation.
2.1. Contents of packaging
Please, check carefully if any physical damage of the screen has not happen during transportation.
Inspect the package for all accessories presented below:
Screen x 1
x6
x 2
x 2
Installation accessories
*)
Wall control switch x 1
x 1+1
x 2
Installation brackets
Regulation wrench x 1
Operation manual x 1
4
2.2 Technical Data
Projection fabrics characteristics:
- Matt White P (MWP) – a special screen dedicated polyester fabric double side covered with vinyl, black back surface
and white front (projection) surface, recommended for application with DLP and LCD multimedia projectors.
Neutral color of the surface enables projection from any directions. Gain: 1.0, viewing angle: 150 degrees,
thickness: 0,7 mm.
- White Ice (WI) – White color vinyl mono foil, matt front size (projection), gloss rear side, dedicated for projection with
LCD and DLP projectors. Fabrics with slightly directional characteristics dedicated for business presentations. Fabrics
of screens bigger than 200cm in height is welded with 2 parts, welding line remains invisible during projection.
Gain 1,2 , viewing angle 120 degrees, thickness 0,4mm.
- New Coral (NC) – Rear projection white vinyl mono foil, gloss front side (projection), matt rear side, dedicated for rear
projection with LCD and DLP projectors. Recommended for business presentations due to directional optical
characteristics of the fabrics. Fabrics of screens bigger than 200cm in height is welded with 2 parts, welding line
remains invisible during projection. Gain 3,2 , viewing angle 90 degrees, thickness 0,6mm.
Instalation rope x 2
Installation template x 1

Screen width
[cm]
Viewing area
size [cm]
Screen
aspect
ratio
Screen case size
W x H x D [cm]
Projection fabrics
max. length
[cm]
Top belt
width [cm]
*)
Version Net
**)
weigth
Dimensions of projection screens.
*) BT and BB versions are available with MWP fabrics
Version BB – 5 cm width black border surrounding the viewing area
Version BT – 5 cm width black border surrounding the viewing area and additional black top 30 cm above the top black border.
**) approximate value for the screen with Matt White P fabrics
Motor:
Electric tubular engine AC:
Voltage: 220-240V AC 50 Hz, 170 W
Power consumption: 0,77A
Rotation speed: 26 rot./min
Torque: 20 Nm
*) *)
Max. operation time : 4 min Engine single cycle operation time, operation cycle can be repeated in 20 minutes intervals.
*
RF remote controller:
Dimensions: 110 x 58 x 20 mm
Power supply: 1 x 12V battery type 23A
5
3. Screen installation
3.1. Installation precautions
- Installation work should be carried out by a qualified technician in accordance with the instructions described below.
- Fixed installation of the screen should be done with use of the screws and anchors suitable for the walls/ceilings
materials at the installation place and the genuine installation brackets delivered with the screen.
- Check carefully after installation if the screen is perfectly leveled. Do not roll out the screen not installed in horizontal
position. In case the screen leveling is not perfect correct the installation.
3.2. Ceiling installation
- Appoint location of the ceiling mount brackets fixing points. Fixing points are located at 4 vertexes of rectangle of B x D
size. Read B and D value related for your screen from the table (see picture 1)
- Drill holes for anchors fixing the screen brackets to the ceiling.
- Assemble the ceiling brackets with components supplied together with the screen. Leave top nuts untight, bottom nuts
should be positioned about 12cm from the bottom end of threaded rod (see picture 2).
450
500
550
600
440 x 247,5(275)
490 x 275,6(306)
540 x 304(338)
590 x 332(369)
16:9(16:10)
16:9(16:10)
16:9(16:10)
16:9(16:10)
332,5
350
380
415
370
410
450
485
290
320
350
385
285
316
343
385
370
410
450
485
35
35
35
35
8
8
8
8
8
8
8
8
-
-
-
-
-
-
-
-
BT
BT
BT
BT
BB
BB
BB
BB
BB
BB
BB
BB
-
-
-
-
-
-
-
-
4:3
4:3
4:3
4:3
16:9(16:10)
16:9(16:10)
16:9(16:10)
16:9(16:10)
16:9(16:10)
16:9(16:10)
16:9(16:10)
16:9(16:10)
4:3
4:3
4:3
4:3
440 x 330
490 x 367,5
540 x 405
590 x 442,5
440 x 247,5(275)
490 x 275,6(306)
540 x 304(338)
590 x 332(369)
450 x 253(281)
500 x 281(312)
550 x 309(344)
600 x 338(375)
450 x 338
500 x 375
550 x 413
600 x 450
461 x 19,5 x 20,2
511 x 19,5 x 20,2
561 x 19,5 x 20,2
611 x 19,5 x 20,2
45
50
55
60

6
Recommended diameter of mounting screws is Ø8 mm. Type of used anchors should be selected according to the
material of the ceiling. Length of anchors is determined by weight of the screen, total bearing capacity of 4 anchors should
exceed 150% of screen net weight.
- Fix ceiling brackets to the ceiling with anchors see Picture 3. Use anchors suitable for the ceiling material and
screen weight.
- Place wooden box containing screen at floor benath brackets fixed to the ceiling, see Picture 4.
- Untight nuts fixing screen’s transport blocking plates and remove blocking plates.
- Drag the through rollers located at both ends of the screen and at the ceiling brackets, see Picture 5.
- Pull slowly the ropes attached to both ends of screen so the screen will be lifted up slowly. Both ropes should be pulled
evenly so the screen would be lifted at horizontal position. You can stop screen lifting at any moment. Lifting ropes
would be left unattended for some period of time, screen will not fall down because ropes are automatically blocked by
claw jaw.
- Stop screen lifting when it will approach distance of 5 cm from the threaded rods of ceiling brackets. Check if the rods
stay at the axis of the screen’s fixing plates holes, see Picture 6. Correct position of rods if required within available
correction range (each pair of rods have correction range of +/- 1cm at each direction horizontally).
Picture 1 Drilling holes for anchors fixing screen’s ceiling brackets
Picture 3 Ceiling brackets installation
Surface width
450cm
500cm
550cm
600cm
A[mm]
Picture 2 Ceiling brackets assembly
B [mm] D [cm]
388,0
185
438,0
185
488,0185
538,0185
588,0185
638,0185
*)
350cm
*)
400cm
*) - sample models available within Customized Screen Program, only
50
50
50
50
50
50

7
Picture 4 Screen ceiling installation - phase 1
Picture 5 Screen ceiling installation - phase 2

8
Picture 6 Screen ceiling installation - phase 3
Picture 7 Screen ceiling installation - phase 4
1
2
3
1- threaded rods fixing nuts
2- screen levelling nuts
3- screen fixing nuts
Check the screen’s rolling tube leveling before first screen’s motor operation.
Do not use the screen if it is not properly installed (leveled).
- Tight threaded fixing nuts (1) to block possible displacement of threaded rods, see picture 7.
- Level the screen, follow procedure described below:
a) Screen levelling nuts were setup about 12cm from the bottom end of threaded rods during assembly of ceiling \
brackets.
b) Check with leveller if both nuts of left side ceiling bracket are levelled, correct their position if necessary.
c) Pull-up left side of the screen with the lifting rope untill screen’s installation plate will base at levelling nuts of left ceiling
bracket.
d) Slowly lift-up right side of the screen with lifting rope untill screen’s rolling tube will reach horizontal position. It is
convenient to place spirit leveller on the rolling tube near right ceiling bracket during this operation. Correct position of
right’s bracket leveling nuts during leveling operation if required.
e) Fix levelled screen, apply fixing nuts at ends of ceiling brackets threaded rods protruding from the holes of screens
installation plates.
f) Check with spirit leveller if the screen’s rolling tube is well levelled. Correct positions of levelling and fixing nuts of right
side inceilling bracket if required.
- Roll-up lifting ropes use reels hiden inside plastic side caps, see Picture 8.
- Fix side caps containing lifting ropes with nuts supplied with the screen, see Picture 9.

3.4. Electric installation
ATTENTION: Electric installation work should be carried out by a certified electrician.
- Lead out the power cables to the place of installation of the wall switch and between wall switch and screen
- Screen power line should be fused with 1A fuse.
- Switch off the screen power line during installation work.
- Manual wall steering switch should be installed at the place meeting the following conditions:
a) installation150-180 cm above the floor level,
b) the screen should be visible by the wall switch operator during the screen operation,
c) wall switch operator cannot stay in reach of any of the screen’s moving parts during the screen operation .
d) the wall switch must be visible from the each part of the room irrespective of the screen position.
Rys.8 Instalacja ekranu na suficie - faza 5
Rys.9 Instalacja ekranu na suficie - faza 6
9

3.5. Screen programming.
!!! NOTICE !!!
The screen was programmed properly at the factory and there is no need to reprogram it without any important
reason. Setting of screen extreme positions was made by manufacturer.
If you need to change the screen extreme position follow the instructions described below.
Picture 10 Screen without remote control system
electric installation
Screen
bl - blue (common)
br - brown (rolling up)
yg - yellow-green (protective)
bk - black (rolling down)
Power line
L1 - brown (live)
N - blue (neutral)
G - yellow-green (protective)
bl yg
bk
br
Programing the length of the rolled out screen (screen bottom bar position).
- Roll up the screen until it will stop automatically in the upper position.
- Insert regulation wrench included in the screen set into the regulation slot (see picture. 11) located in the left bottom
part of the screen .
Regulation knob “2” (bottom/back) enables setting of the bottom extreme position of the screen bottom bar:
„+” - increase the length of the fabrics is rolled down when the screen is rolled out,
„–” - decrease the length of the fabrics is rolled down when the screen is rolled out.
Regulation knob “1” (top/front) enables setting of the top extreme position of the screen bottom bar:
“-“ - increase the lenght of the fabrics is rolled down when the screen is rolled in,
“+” - decrease the length of the fabrics is rolled down when the screen is rolled in.
~
Picture 11 Lower bar fine tuning
10
IMPORTANT!
Do not decrease (tuning knob 1+) the range of the rolled down surface. It can damage the screen.
Do not increase (regulation 2+) the range of the surface which was rolled down behind the STOP mark, placed in
the upper right corner of the screen. Rolling down the screen behind the mark can damage the screen.
Avers screens are invented and manufactured to provide best possible projection surface flatness when rolled out
to the designed height. Surface flatness would be affected if the screen is not rolled out completely or is rolled out
over the designed size.

5. Warranty conditions
1) Avers screens warranty period is 24 months from the date of purchase confirmed with the original purchase invoice.
2) Extended warranty period for electric engine is 60 month.
3) Surety commits to fix free of charge any failures (component or production defects) of the product which appear during
warranty period.
4) Warranty exclusions :
a) the failures caused by the usage of the screen against the rules described in operation manual,
b) the failures caused by improper storage or transportation,
c) mechanical defects of the screen other than mentioned at point 3),
d) damages caused with overvoltage at power network,
e) deinstallation and reinstallation of the screen.
5) Avers Screens Service department will remove all defects within 21 days after receiving the demaged product.
6) Warranty claims should be passed to the screen supplier (dealer).
At other cases please contact service.
4. Screen operation
Projection screen AVERS can be operated manually with wall switch is installed.
4.1. Manual operation
Manual screen operation is possible with the wall control switch or by radio frequency transmitter of the optional remote
control system.
- Push button „‚”, the screen will begin to roll down and stop automatically at the bottom position after rolling down.
- Push “Stop” button of the remote transmitter, screen rolling operation will be stopped.
- Push button „”, the screen will begin to roll up and stop automatically in the upper position after rolling up.
4.2. Screen maintenence
Pojection screen Avers do not require periodical service maintenance. Clean dust from the screen case and fabrics with
dry soft cloths. If needed use moisturized cloth with soft detergent to remove stains. After stain removal dry the cleaned
surface with cloth carefully.
4.3. Before calling the service
Symptoms
The screen fabrics does not
roll down
Reasons
Power failure
Remedy
Check the screen’s circuit fuse and the
power cable
The screen fabrics does not
roll down smoothly
The screen stops in the
middle position.
The screen was not installed properly in
horizontal position.
There are some objects on the bottom bar
way.
Power failure
Check if the screen case is properly leveled.
Reinstall the screen correctly.
Remove the objects which can block the
proper work of the screen or are at the
bottom bar way.
Check the propriety of electric installation
and the state of the power wires.
11

Wersja D10.06.2017
Manufactured after 13.08.2005
This symbol on the products and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste. Disposing of this
product correctly will help to save valuable resources and prevent any potentialnegative effects
on human health and the environment which could otherwise arise from inappropriate waste
handling. Please contact your local authority for further details of your nearest designated
collection point.

13 45 6
2
Screen brackets ceiling installation with tape template

13 45 6
2
Screen brackets wall installation with tape template