Avery Dennison 6054 User manual

OPERATING INSTRUCTIONS
Use these Operating Instructions to assemble and use
the 6054 Network Control Module and the 6055 Docking
Module.
The 6054 Network Control Module controls one to four
6055 Docking Modules, which provides Pathfinder® 6057
printer charging and Ethernet communication capability
The 6054 Network Control Module and 6055 Docking
Module can only be used with printers that contain the
approved battery as listed in the printer documentation.
Refer to the Operator’s Handbook for additional important
battery safety information.
Follow the operating and storage limit specifications
listed at the end of these instructions. Otherwise, the
battery may permanently lose its charge capacity.
Note: You must charge the printer before using it.
TC6054OI Rev. AD 9/13 ©2010 Avery Dennison Corp. All rights reserved.
6054 Network
Control Module
6055 Docking Modules

Assembling the Network Control Module
1. Turn over the 6055 Docking Module and 6054 Network
Control Module.
2. Using a Philips screwdriver, remove the end cap from
the Network Control Module.
End
Cap
Network Control
Module
3. Using a Philips screwdriver, loosen two screws on the
6055 Docking Module and slide the connector plate
under the screws. Tighten the screws.
Connector Plate
Docking
Module
Network Control
Module
2

4. Loosen the two screws on the 6054 Network Control
Module and slide the 6054 Network Control Module
onto the Docking Module’s connector plate. Tighten
the screws.
End
Cap
5. Using a Philips screwdriver, attach the end cap to the
end of the 6055 Docking Module.
6. Carefully turn over the Network Control Module.
You can connect up to four Docking Modules with each
Network Control Module. Repeat steps 3 – 6 for each
additional Docking Module. Make sure you attach the
end cap to the final Docking Module.
3

Setting up the Network Control Module
1. Plug the supplied power cable into the Network
Control Module.
2. Plug the other end of the cable into a grounded
electrical outlet. The green power LED on the 6054
Network Control Module turns on.
3. Connect the communication cable from the host to the
Network Control Module.
Communication Cable
goes here
For Use in Brazil
In order to meet the compliance requirements of Brazil, Network Module,
whose model is 6054, should be fed by the source model:
FSP FSP084-DMAA1, Input: 100-240Vac, 50-60Hz, 1.3A, Output:
12Vdc, 7.0A, LPS. Or Edac Power Electronics Co.
And 10953A Input: 100-240Vac, 50-60Hz, 2.5A, Output: +12 Vdc, 6.6a,
80W, LPS. along with the surge protector model Clone F1W.
A fim de atender aos requisitos de conformidade do Brasil, o Network
Module, cujo modelo é 6054, deve ser alimentado pela fonte de modelo:
FSP FSP084-DMAA1, Input: 100-240Vac, 50-60Hz, 1.3A, Output:
12Vdc, 7.0A, LPS. ou Edac Power Electronics Co., E 10953A Input: 100-
240Vac, 50-60Hz, 2.5A, Output:+12Vdc, 6.6A, 80W, LPS
junto com o protetor de surto de modelo Clone F1W.
4

Charging the Battery
Charge the battery while it is inside the printer. Slide the
printer into the Docking Module until you hear a click.
Power LED
The green power LED on the 6054 Network Control
Module turns on when there is power to it.
Charging time can take up to three hours. It takes
approximately 1 hour to reach the 80% level (where it is
now usable). To reach 100%, it takes approximately 2
hours more.
Reading the Display
Charging LED – flashes
when you insert the printer;
on (solid) during charging;
off when charging is
complete.
Complete LED – flashes when the printer’s battery is
80% charged; on (solid) when the battery is 100%
charged.
Note: Both LEDs are ON continuously when the docked
printer’s firmware is updating. Do not remove
the printer or disconnect power to the Docking
Module at this time.
5

6
Using the Printer’s LED
The Monarch® 6052 and 6057 printers have a multicolor
LED located above the display. The printer’s default
settings are:
LED Status
Red Printer Error
White Out of Supply
Blue Low Battery
When printer is docked (with charger model 6054/6055)
Blinking green Network connection
Blinking magenta No network connection
Note: When the LED is blinking red, the printer is receiving
information and should not be turned off, removed
from or placed in the docking station.
Troubleshooting
When an error occurs, the Docking Module’s Charging
and Complete LEDs blink together. In this case, remove
the printer, wait for the lights to stop flashing, then re-
insert the printer. If the error still occurs, put a new
battery into the printer and place the printer back into the
charger. If there is a problem after the second attempt to
charge, call Service.

7
Specifications
Operating Limits:
Temperature 32°F to 104°F (0°C to 40°C)
Humidity 5% to 90% non-condensing
Storage Limits:
Temperature -40°F to 158°F (-40°C to 70°C)
Humidity 5% to 90% non-condensing
One Docking Module
Length: 8.6” (218 mm)
Width: 4.75” (121 mm)
Height: 3.4” (86 mm)
Weight: 1.7 lbs. (0.7 kg)
Shipping Weight: 2.2 lbs. (1 kg)
Network Control Module
Length: 7” (178 mm)
Width: 3.5” (89 mm)
Height: 2.25” (57 mm)
Input: 12 to 16 VDC/50W
Weight: 2.2 lbs. (1 kg)
Shipping Weight: 2.7 lbs. (1.2 kg)
Power Supply
Input: Universal switching power supply, 85 to
264 VAC, 50/60 Hz.
Output: 12 VDC/80W max

8