Avitech Sequoia 2H2U User manual

User Manual
Sequoia 2H2U
One of a kind multiviewing
Revision 1.0.3, (May, 2014)

User Manual
ii
ABOUT THIS MANUAL
This manual contains information on how to use the Avitech Sequoia 2H2U mouse keyboard controller. There are 3
chapters in this manual.
Getting Started introduces the features and specifications as well as the external components of the Avitech
Sequoia 2H2U.
System Configuration discusses the process of setting up the Sequoia 2H2U.
Basic Operations, introduces the 2 types of operating modes. Using the mouse and keyboard hot-keys to
perform basic operations as well as using the touch-screen display with Avitech Sequoia 2H2U.
The following conventions are used to distinguish elements of text throughout the manual.
provides additional hints or information that require special attention.
identifies warnings which must be strictly followed.
Any name of a menu, command, icon or button displayed on the screen is shown in a bold typeset. For example: On
the Start menu select Settings.
To assist us in making improvements to this user manual, we welcome any comments and constructive criticism.
Please email us at: [email protected].
WARNING
Do not attempt to disassemble the Sequoia 2H2U. Doing so may void the warranty. There are no serviceable parts
inside. Please refer all servicing to qualified personnel.
TRADEMARKS
All brand and product names are trademarks or registered trademarks of their respective companies.
COPYRIGHT
The information in this manual is subject to change without prior notice. No part of this document may be
reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, without the
express written permission of Avitech International Corporation. Avitech International Corporation may have
patents, patent applications, trademarks, copyrights or other intellectual property rights covering the subject matter
in this document. Except as expressly written by Avitech International Corporation, the furnishing of this document
does not provide any license to patents, trademarks, copyrights or other intellectual property of Avitech International
Corporation or any of its affiliates.
TECHNICAL SUPPORT
For any questions regarding the information provided in this guide, call our technical support help line at
425-885-3863, or our toll free help line at 1-877-AVI-TECH, or email us also at [email protected].

iii
Contents
About This Manual....................................................................................................................ii
Warranty.....................................................................................................................................v
Limitation of Liability................................................................................................................v
Extended Warranty Options.....................................................................................................v
Services and Repairs Outside the Warranty Period..............................................................v
Regulatory Information ............................................................................................................v
Federal Communications Commission (FCC) Statement.....................................................v
European Union CE Marking and Compliance Notices ........................................................v
Australia and New Zealand C-Tick Marking and Compliance Notice..................................v
1. Getting Started ............................................................................................................1
1.1 Package Contents..............................................................................................................1
1.2 Product Features ...............................................................................................................3
1.3 Specifications ....................................................................................................................4
1.4 Connections to the Sequoia 2H2U...................................................................................5
2. System Configuration .................................................................................................7
2.1 Getting the Sequoia 2H2U Ready.....................................................................................7
2.1.1 Basic Setup When Connecting to an Regular or Touch-screen Display.........7
2.1.2 Basic Setup When Cascading Sequoia Devices..............................................10
3. Basic Operations.......................................................................................................12
3.1 Host Operation Mode ......................................................................................................13
3.1.1 Pop-up Selections...............................................................................................13
3.1.2 Functions .............................................................................................................13
3.1.3 Hot-keys ...............................................................................................................14
3.2 Remote Operation Mode.................................................................................................15
3.2.1 Hot-keys...............................................................................................................15
Appendix A Using the Surfer Feature..........................................................................17
A.1 “Surfer” Feature on Uniform Quad Layout That Fills Entire Screen..........................17
A.2 “Surfer” Feature on Non-uniform Quad Layout ...........................................................19
A.3 “Surfer” Feature on Full Screen “Source” Window .....................................................19
A.4 “Surfer” Feature on Cascaded System .........................................................................20
Appendix B Using the Touch-screen...........................................................................21
B.1 Lock/Unlock Window Layout..........................................................................................21
B.2 Pop-up Selection .............................................................................................................22
B.3 Audio Tally .......................................................................................................................22
B.4 Move/Resize Window ......................................................................................................23
B.5 Exit from Remote Operation Mode to Host Operation Mode ......................................23
B.6 Switch Control (Cycle) Between Windows....................................................................25

iv
Appendix C Using the Touch-to-Mouse Utility (for Windows XP only).....................27
Appendix D Resetting to the Factory-Default State....................................................28

v
Warranty
Avitech International Corporation (herein after referred to as “Avitech”)
warrants to the original purchaser of the products manufactured in its
facility (the “Product”), that these products will be free from defects in
material and workmanship for a period of 1 year or 15 months from the
date of shipment of the Product to the purchaser. There is a 3 month
grace period between shipping and installation.
If the Product proves to be defective during the 1 year warranty period,
the purchaser’s exclusive remedy and Avitech’s sole obligation under
this warranty is expressly limited, at Avitech’s sole option, to:
(a) repairing the defective Product without charge for parts and labor;
or (b) providing a replacement in exchange for the defective Product;
or (c) if after a reasonable time is unable to correct the defect or
provide a replacement Product in good working order, then the
purchaser shall be entitled to recover damages subject to the limitation
of liability set forth below.
Limitation of Liability
Avitech’s liability under this warranty shall not exceed the purchase
price paid for the defective product. In no event shall Avitech be liable
for any incidental, special, or consequential damages, including
without limitation, loss of profits for any breach of this warranty.
If Avitech replaces the defective Product with a replacement Product
as provided under the terms of this Warranty, in no event will the term
of the warranty on the replacement Product exceed the number of
months remaining on the warranty covering the defective Product.
Equipment manufactured by other suppliers and supplied by Avitech
carries the respective manufacturer’s warranty. Avitech assumes no
warranty responsibility either expressed or implied for equipment
manufactured by others and supplied by Avitech.
This Warranty is in lieu of all other warranties expressed or implied,
including without limitation, any implied warranty of merchantability or
fitness for a particular purpose, all of which are expressly disclaimed.
This Hardware Warranty shall not apply to any defect, failure, or
damage: (a) caused by improper use of the Product or inadequate
maintenance and care of the Product; (b) resulting from attempts by
other than Avitech representatives to install, repair, or service the
Product; (c) caused by installation of the Product in a hostile operating
environment or connection of the Product to incompatible equipment;
or (d) caused by the modification of the Product or integration with
other products when the effect of such modification or integration
increases the time or difficulties of servicing the Product.
Any Product which fails under conditions other than those specifically
covered by the Hardware Warranty, will be repaired at the price of
parts and labor in effect at the time of repair. Such repairs are
warranted for a period of 90 days from date of reshipment to customer.
Extended Warranty Options
Avitech offers OPTIONAL Extended Warranty plans that provide
continuous coverage for the Product after the expiration of the
Warranty Period. Contact an Avitech sales representative for details
on the options that are available for the Avitech equipment.
Services and Repairs Outside the Warranty Period
Avitech makes its best offer to repair a product that is outside the
warranty period, provided the product has not reached its end of life
(EOL). The minimum charge for such repair excluding shipping and
handling is $200 (US dollars).
AVITECH INTERNATIONAL CORPORATION
● 15377 NE 90th Street Redmond, WA 98052 USA
● TOLL FREE 1 877 AVITECH
● PHONE [phone]
● FAX [phone]
●[e-mail]
● http://avitechvideo.com
Regulatory Information
Marking labels located on the exterior of the device indicate the
regulations that the model complies with. Please check the marking
labels on the device and refer to the corresponding statements in this
chapter. Some notices apply to specific models only.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense. Properly
shielded and grounded cables and connectors must be used in order
to meet FCC emission limits. Avitech is not responsible for any radio or
television interference caused by using other than recommended
cables and connectors or by unauthorized changes or modifications to
this equipment. Unauthorized changes or modifications could void the
user's authority to operate the equipment. Operation is subject to the
following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
European Union CE Marking and Compliance Notices
Statements of Compliance
English
This product follows the provisions of the European Directive
1999/5/EC.
Dansk (Danish)
Dette produkt er i overensstemmelse med det europæiske direktiv
1999/5/EC.
Nederlands (Dutch)
Dit product is in navolging van de bepalingen van Europees Directief
1999/5/EC.
Suomi (Finnish)
Tämä tuote noudattaa EU-direktiivin 1999/5/EC määräyksiä.
Français (French)
Ce produit est conforme aux exigences de la Directive Européenne
1999/5/EC.
Deutsch (German)
Dieses Produkt entspricht den Bestimmungen der Europäischen
Richtlinie 1999/5/EC.
Ελληνικά (Greek)
To προϊόν αυτό πληροί τις προβλέψεις της Ευρωπαϊκής Οδηγίας
1999/5/EC.
Íslenska (Icelandic)
Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer
1999/5/EC.
Italiano (Italian)
Questo prodotto è conforme alla Direttiva Europea 1999/5/EC.
Norsk (Norwegian)
Dette produktet er i henhold til bestemmelsene i det europeiske
direktivet 1999/5/EC.
Português (Portuguese)
Este produto cumpre com as normas da Diretiva Européia 1999/5/EC.
Español (Spanish)
Este producto cumple con las normas del Directivo Europeo
1999/5/EC.
Svenska (Swedish)
Denna produkt har tillverkats i enlighet med EG-direktiv 1999/5/EC.
Australia and New Zealand C-Tick Marking and
Compliance Notice
Statement of Compliance
This product complies with Australia and New Zealand's standards for
radio interference.

1
1. Getting Started
The Avitech Sequoia 2H2U is a highly innovative device. The Sequoia integrates the functions of a KVM
(keyboard video mouse) switch and a robust multi-viewer into one enclosure. The Sequoia 2H2U
provides a simple solution for any user who works in an environment with multiple computer systems
and Pro A/V equipment. With the Sequoia 2H2U seamlessly switch up to 2 computers and 2 video
signals; and control up to 2 computers with just one keyboard and mouse. Additionally, its scalability
(through cascading) allows the Sequoia to be ideal for both individual users and corporate applications.
The Sequoia features a visual user interface (Host operation mode) which allows users to configure the
layout through an OSD (on screen display).While in Host operation mode easily convert video images to
full screen, adjust windows to any size and move windows to any position. Also, for a hands-on user
experience,the Sequoia 2H2U can be used with a touch-screen display. The touch-screen controls are
powerful and intuitive; switch sources, resize windows, move windows to any position, and control a
remote computer with a tap of your finger.
This chapter introduces the features and specifications as well as the external components of Avitech
Sequoia 2H2U.
1.1 Package Contents
After unpacking the shipping carton, the following standard items can be found:
Avitech Sequoia 2H2U
Utility Disc (software and user manual)
12 V DC/5A Power Adapter
Standard Power Cord (USA customers only)

2
Rubber Foot (4 pcs)
D
USB-A to USB-B Cable
HDMI Cable (optional)
D
Sequoia 5-in-1 Cable (optional)
DVI to HDMI Adapter (optional)
D
Table 1-1 Package Contents
The following items are included if optional rack mount kit is ordered.
Front Bracket
Power Adapter Tray

3
Multi angle hex driver (2 mm)
FH MSH AB 3×6 Screws (12 pieces)
Table 1-2 Optional Rack Mount Package Contents
1.2 Product Features
The Sequoia 2H2U is HDCP-compliant and capable of HDMI and DVI output (DVI through an adapter).
It features automatic detection and selection of optimum display resolution, automatic sensing of input
signal, flexible window configuration (any size, any position), Picture-in-Picture (PiP) overlay display,
video loss detection, image/gain (can be adjusted manually or automatically), and crop/pan image.
The Sequoia can control up to 2 computers and 2 video sources and can automatically detect PS/2 &
USB interfaces. It is also hot-pluggable which allows the addition/removal of computers without
powering down devices. The Sequoia’s front panel features LED indicators for monitoring the following:
Connected Computers (Active or Standby), Operation Mode (Host or Remote) and Power.
For audio monitoring the Sequoia 2H2U features two built-in speakers, a 1/8 inch headphone jack and
an on screen display (OSD) of audio meters. The Sequoia 2H2U accepts embedded/HDMI®audio
(7.1ch, 5.1ch, 2ch-stereo) and analog audio (stereo). To assist with audio/video re-syncing the Sequoia
2H2U features up to 170ms of audio delay.
Fully utilize the flexibility of the Sequoia 2H2U with Avitech’s Phoenix-G software (formerly called
Galaxy). With Phoenix-G control software you can easily configure display options, crop/pan images,
save up to 23 presets and even program a list of display layouts for the Sequoia to automatically cycle
through (“Briefing”feature –refer to Sequoia 2H2U Phoenix-G manual for more details). Moreover, with
Avitech’s Hook utility (patent pending), a laptop can be used to control the Sequoia 2H2U via the USB
port on the front panel .
For larger applications cascade up to 5 Sequoia 2H2U’s and control up to 10 computers and 10 video
sources, SDI (3G/HD/SD) CVBS (NTSC/PAL), with just one keyboard and mouse.
1. Non-standard keyboards (e.g., keyboards with a USB hub, keyboards that need driver installation and
programmable keyboard, etc.) are not supported.
2. Compatibility between the computer and the Sequoia 4H may depend on the computer’s BIOS Setup. If
an incompatibility occurs, you may refer to the computer’s BIOS Setup and make sure USB port and
PS/2 port are enabled if these items exist in the computer’s BIOS Setup (typically found in the
"Advanced" or "Onboard Device Configuration" menu).
3. Hook utility currently supports the Sequoia solo series (non-cascaded) and the Pacific X-HDU (an
HDMI transmitter-Pacific X-HDUT (TX) and an HDMI receiver-Pacific X-HDUR (RX) allows
transmission of 1080p60 HD over 100 meters based on HDBaseT®technology –refer to Pacific X-HDU
user manual for more details). Connect a laptop (or desktop) computer to the Sequoia solo series or
Pacific X-HDU and simulate keyboard/mouse function for remote control processing (KVM feature).
4. Refer to Avitech Hook utility user manual for more details.

4
1.3 Specifications
Input
HDMI or DVI
(through DVI to HDMI adapter)
Automatic sensing
HDMI mode:
480i, 480p, 576i, 576p, 720p, 1080i, 1080p
DVI-D mode:
Up to 1920×1200
Transmission of audio signal is not included when using the DVI to
HDMI adapter.
SDI
Automatic sensing
3G-SDI: 1080p 23.98/24/25/29.97/30/50/59.94/60Hz
(up to 100 meters)
HD-SDI: 720p, 1080i 50/59.94/60Hz
SD-SDI: 480i, 60Hz / 576i, 50Hz
NTSC/PAL analog composite signals
Output
HDMI or DVI
(through DVI to HDMI adapter)
Automatic sensing or user selectable
Up to 1920×1200 (WUXGA) at 50Hz/60Hz or 1600×1200
(UXGA) 75Hz
Up to eight channel (7.1) audio configuration
Transmission of audio signal is not included when using the DVI to
HDMI adapter.
Others
Peripheral sharing
USB type A port (for USB 2.0 hub) ×2
Computer
connection
Up to 2 units (maximum)
Port switching
Method:
Keyboard hot-keys (both in Host and Remote operation modes)
Mouse
OSD (pop-up menu –in Host operation mode)
Surfer feature (in Remote operation mode)
Power
Power consumption is 25W
Power Supply (adapter):
Input (AC): 100 to 240V 50Hz/60Hz
Output (DC): 12V DC/5A
Operating System
Microsoft Windows 98 Special Edition, 2000 Professional, XP, Vista,
Server 2003, Server 2008, Windows 7, Windows 8
Mac (O/S X 10.5 or later version only)
Linux OS: Fedora 10, Ubuntu 8.1, Scientific 5.2, RedHat, Mint 6.0,
Debian 5.0, PC Linux OS 2009, SUSE 11.1, Mandriva 2009, CentOS
5.2
Note: Windows NT is not supported
Dimensions/Weight
Dimensions: 261×174×44 mm (10.3×6.9×1.7 inch)
Weight: 1.3 kg (2.8 lb)
Environment/Safety
Temperature:
Operating: 0  C (32  F) to 40  C (104  F)
Storage: –10  C (14  F) to 50  C (122  F)
Humidity: 0% to 80% relative, non-condensing
Safety: FCC/CE/C-Tick/Class B
Table 1-3 Specifications

5
1.4 Connections to the Sequoia 2H2U
Figure 1-1 Sequoia 2H2U Components
Front Panel
Stereo Speaker
Set
Embedded speakers for monitoring audio.
(Volume can be adjusted and output can be enabled/disabled.)
Indicators
PWR
Glows green when the Sequoia 2H2U is turned ON.
MODE
Glows green when the Sequoia is in Host operation mode.
Glows amber when the Sequoia is in Remote operation mode.
1and 3
Glows green when a particular computer is operating under
Remote operation mode (full control through keyboard and
mouse).
Glows amber when a particular computer is operating under Host
operation mode (monitoring only).
Blinks amber on a particular re-booting or powered-off computer
connected to the Sequoia 2H2U.
LED indicators 2and 4have been disabled.
Audio In/Out

Connects to the green connector for headphone function (stereo).

Connects to the red connector for microphone function.
USB Type A
(keyboard/mouse)
Connects to a USB mouse and keyboard. Use these ports for control in
Host operation mode.
USB Type B
Connects to a remote computer for control through USB mouse and
keyboard.
USB Type A
(peripheral sharing)
These 2 ports can connect to a USB 2.0 hub, USB flash disk, etc.

6
Rear Panel
HDMI Output
HDMI connector for HDMI/DVI output
(a DVI to HDMI adapter may be required)
5-in-1 Input
Use the Sequoia’s proprietary 5-in-1 cable for connections
Inputs 1/3: connect to remote computer’s USB, PS/2 and audio ports
Inputs 2/4: connect to an A/V device’s audio connector
HDMI Input 1/3
HDMI connectors for HDMI/DVI inputs
(a DVI to HDMI converter may be required)
BNC Input 2/4
BNC connectors for SDI (3G/HD/SD) CVBS (NTSC/PAL) video inputs.
Note: SDI embedded audio is also supported.
Power
(DC 12V)
Connects to the 12V DC/5A power adapter
Ethernet (IP)
For setup using the Phoenix-G software (Galaxy) and control using ASCII
Z commands via a network connection
(Protocol: TCP/IP, UDP)
Dip Switches
Resets the Sequoia to factory-default settings; or updates firmware
Power Switch
Turns the Sequoia 2H2U power ON and OFF
Table 1-4 Sequoia 2H2U Component Description

7
2. System Configuration
This chapter discusses the process of setting up Sequoia 2H2U.
2.1 Getting the Sequoia 2H2U Ready
The Sequoia 2H2U can be connected to most monitors and some touch-screen displays. It can also be
cascaded with up to five (5) Sequoias for larger applications.
To control the Sequoia 2H2U directly, connect a keyboard and mouse to the USB port on its front
panel. Alternatively, to control the Sequoia remotely, use a laptop (or desktop) computer and connect to
the Sequoia’s USB (type B) port on its front panel, (use a USB A/B cable). Then, run Avitech’s Hook
software utility on the controlling computer to simulate mouse and keyboard operation.
1. Hook utility currently supports the Sequoia solo series (non-cascaded) and the Pacific X-HDU (an
HDMI transmitter-Pacific X-HDUT (TX) and an HDMI receiver-Pacific X-HDUR (RX) allows
transmission of 1080p60 HD over 100 meters based on HDBaseT®technology –refer to Pacific X-HDU
user manual for more details). Connect a laptop (or desktop) computer to the Sequoia solo series or
Pacific X-HDU and simulate keyboard/mouse function for remote control processing (KVM feature).
2. Refer to Avitech Hook utility user manual for more details.
2.1.1 Basic Setup When Connecting to an Regular or Touch-screen Display
The following figure shows a typical setup with an Avitech Sequoia 2H2U connected to two computers
and two A/V devices.
DO NOT place any object on the top or side panels of the Sequoia 2H2U.
Doing so could affect its internal components and/or its heat dissipation.
Figure 2-1 Sequoia 2H2U with Regular Display Setup

8
Figure 2-2 Sequoia 2H2U with Touch-screen Display Setup
Step 1. Connect the 5-in-1 cable to the first computer’s USB or PS/2 port and then connect the 5-in-1
cable to its audio ports (mic in, audio out). Connect the other end of the 5-in-1 cable to the
Sequoia’s source 1port (DB15 connector at rear panel). Repeat this process for the second
computer and connect to SOURCE 3.
1. We highly recommend using a USB connection instead of a PS/2 connection when available. In case
no USB connection is available and a PS/2 connection must be utilized, make sure to first power on the
Sequoia 2H2U, then turn on the computer afterwards.
2. (For Windows 2000 users) Upon connecting the Sequoia through USB for the first time to the
computer, perform the windows on-screen steps to initialize the USB connection.
Step 2. Connect the first A/V device’s audio output to the Sequoia 2H2U’s SOURCE 2 input (DB15
connector on rear panel) via the 5-in-1 cable. Repeat this process for the second A/V device
and connect to SOURCE 4.
Step 3. Connect a HDMI or DVI (DVI through an adapter) display to the HDMI OUT port on the
Sequoia’s rear panel.
Step 4. Connect the first computer’s HDMI or DVI (DVI through an adapter) output to the Sequoia
2H2U’s VIDEO IN 1 port (HDMI connection). Repeat this process for the second computer and
connect to VIDEO IN 3.
Step 5. Connect the first A/V devices BNC output to the Sequoia’s VIDEO IN 2 port with a BNC cable.
Repeat this process for second A/V device and connect to VIDEO IN 4.
Step 6. Connect the mouse and keyboard to the mouse/keyboard USB ports located on the
Sequoia 2H2U’s front panel. When connecting 3 or more devices at the same time such as; a
touch-screen, a mouse and a keyboard you can connect a USB hub to increase the number of
USB connections. (refer to Figure 2-2)
Non-standard keyboards (e.g., keyboards with a USB hub, keyboards that need driver installation and
programmable keyboard, etc.) are not supported.
Step 7. Connect the provided 12V DC power adapter and then power on the Sequoia.

9
1. For computers using the PS/2 connection instead of a USB connection; re-boot at this time.
2. It is not necessary to re-boot computers connected via USB connection (plug and play feature).
Step 8. Move the mouse or press the Pause/Break key to display the Sequoia’s Host cursor (will
disappear again after 5 seconds of inactivity). Move the mouse again to display the Host cursor.
Step 9. The pop-up menu will appear upon moving the cursor to the window’s top right
position.
Click the symbol or double-click the left mouse button on the desired window to enter
Remote operation mode.
Remote operation mode connects you directly to the selected computer.
The Sequoia’s (Host) keyboard and mouse will now control the selected computer.
Item not applicable for Sequoia 2H2U with touch-screen display setup or PS/2
connection –
“Surfer”feature (default setting is “on”) is enabled, moving the mouse to the same border
that is shared with another remote computer will cause the Sequoia’s (Host) keyboard and
mouse to control another selected computer. Pressing Alt + Ctrl + Shift + F10will toggle
this feature “off”and “on.”
When connecting to touch-screen display
Press Ctrl + Ton the keyboard to perform a screen calibration.
This is necessary when connecting to a touch-screen for first time or upon resetting the Sequoia 2H2U.
The following symbol will appear in the top left portion of the screen:
Use a stylus or a finger to press on the center of the symbol until the next symbol appears
(takes approximately five seconds).
Perform this step each time the symbol appears (top left, top right, lower left, lower right).
Upon completing screen calibration the Sequoia will return to Host operation mode and the four
source windows will re-appear on screen.

10
2.1.2 Basic Setup When Cascading Sequoia Devices
Cascading is the technique of “daisy-chaining” Sequoia devices (up to 5) through a USB A/B cable. Only
the keyboard and mouse are cascaded. Other functions (e.g., audio, video, and USB hub) are not, and
depend on the output from each individual computer and the associated Sequoia. (see Figure 2-3)
The following figure shows 3 Sequoia 2H2U cascaded together; with each Sequoia 2H2U connected to
2 computers.
Cascading is available on the Sequoia 2H2U, 4H and 2x2V.A combination of any of these Sequoia devices
can be cascaded to meet custom applications.
Figure 2-3 Cascading Three Sequoia 2H2U’s Setup
Step 1. Perform steps 1 –7 for the first Sequoia 2H2U as outlined for Regular Display in the previous
section “Basic Setup When Connecting to a Regular or Touch-screen Display.”
Step 2. Repeat the above-mentioned steps for the second and third Sequoia 2H2U to be cascaded.
Step 3. Connect a mouse and keyboard to the USB ports located on the Sequoia’s front panel.
(first Sequoia only)
Step 4. Connect first Sequoia’s USB (type-B) port to second Sequoia’s USB (type-A) port
using standard USB A/B cable. Repeat this procedure to connect second Sequoia to the third.
Step 5. Move the mouse or press Pause/Break key and Host cursor will appear on display (will
disappear again after 5 seconds of inactivity). Move the mouse again to display the Host cursor.
Step 6. Place the cursor on the display of the master/first Sequoia 2H2U, (the one with the mouse and
keyboard connected to it), then perform a system configuration reset by pressing:
Ctrl + Shift + Alt + R. The reset takes approximately four seconds for each module. During this
process each Sequoia’s Mode –LED turns off, one at a time.
Step 7. Move Host cursor across all 3 displays to allow system to complete USB device initialization.
If the cursor is unable to move over all three displays, perform steps 5 and 6 again.

11
Step 8. The pop-up menu appears when the Host cursor is moved over the top right portion of
a window.
Click the symbol or double-click the left mouse button on the desired window to enter
Remote operation mode.
Remote operation mode connects you directly to the selected computer.
The Sequoia’s (Host) keyboard & mouse will now control the selected computer.
This item is not applicable for Sequoia 2H2U with touch-screen display cascaded setup or
with PS/2 connection –
“Surfer”feature (default setting is “on”) is enabled, moving the mouse to the same border
that is shared with another remote computer will cause the Sequoia’s (Host) keyboard and
mouse to control another selected computer. Pressing Alt + Ctrl + Shift + F10will toggle
this feature “off”and “on.”

12
3. Basic Operations
There are 2 types of operating modes while using the Sequoia 2H2U; Host operation mode and Remote
operation mode. This chapter discusses both operational modes.
Host Operation Mode
When the Sequoia 2H2U is in Host operation mode, the Host cursor is controlled by the locally
connected mouse device. Or in the case of a cascaded setup the cursor is controlled by the mouse
device that is connected to the Master Sequoia. The Host cursor controls the positions and sizes of the
windows for up to two remote computers and 2 A/V sources (up to 10 of each when cascaded).
Upon re-connecting a keyboard or mouse, the cursor may disappear.
Press the Pause/Break key to solve this problem.
Remote Operation Mode
When the Sequoia 2H2U is in Remote operation mode, the mouse cursor and keyboard are used to
control a specific computer connected to the Sequoia 2H2U.
Understanding the Terminology:
USB host –refers to mouse/keyboard USB ports located on the Sequoia 2H2Ufront panel.
USB device –refers to the DB15 connector (source 1and 3ports) located on the Sequoia 2H2U
rear panel that connects to the computer’s USB port through the 5-in-1 cable.
Tips on Navigating the Sequoia 2H2U:
Up to 2 computers and two A/V sources can connect to a single Sequoia 2H2U. Sequoia puts
each input source in a window and can display all 4 windows on one output display. Thus, 2
computers and 2 video signals can be displayed and controlled from a single monitor.
When Host operation mode is active, use the mouse connected to the Sequoia to re-size and
re-position any window on the output display.
To switch operation to a remote computer; move the Host cursor into a specific window on the
screen and then click the “enter icon” or double-click the left mouse button.
Remote operation mode works with computers only, Remote operation mode cannot be entered
on video sources (e.g., Blu-Ray player).
When Remote operation mode is active, use mouse and keyboard to operate a single computer.
Note: The computer is displayed within a window on the monitor.
When in Remote operation mode, the master Sequoia 2H2U automatically transfers the mouse
and keyboard control to the selected computer.
To switch back to Host operation mode, use “Pause/Break”hot-key. Host cursor will reappear.

13
3.1 Host Operation Mode
In this mode, monitor a quad screen or double-click the window of the particular computer to be
controlled. Following are the basic operations that can be performed in Host operation mode.
3.1.1 Pop-up Selections
Upon moving the Host cursor to the top right corner of a window, the following pop-up icons appear.
: swap window
: enter a computer window
: full screen
: return from full screen
When the Sequoia has detected that a particular computer’s USB (or PS/2) port is not connected, then the
enter pop-up icon is not shown on that window (only USB connections are hot-pluggable).
3.1.2 Functions
The Sequoia 2H2U allows the swapping of window position, window size adjustment, and audio output
selection. Following are the summarized Host operation mode functions.
Function
Window resizing
Drag the border of a window to a desired size
Window
repositioning
Drag a window to a new position
Window position
swapping
Move the Host cursor to the top right corner of a window, click the Sicon
and then move the cursor (now a capital letter S) to the destination
window and click the left mouse button.
Full screen
window
Move the Host cursor to the top right corner of awindow, click the icon
then the window will maximize to full screen. Select to return back
from full screen.
Access a remote
computer
Method 1:
Move the Host cursor to the top right corner of a remote computer
window, click to access the Remote operation mode.
Method 2:
Move the Host cursor so it is on the desired remote computers’window
and double-click.
Lock/unlock
window layout
Move the Host cursor to the top left corner of the display until the cursor
becomes a capital letter L, then click to lock the window layout. Repeat
these steps to unlock the layout.
Enable/disable
audio output
Double-click the audio tally (green) and it will turn to (red) to
signify that audio output is coming from a window.
Note: To enable an audio output from a source that is not the active
window, refer to the Phoenix-G (Galaxy) user manual.
Table 3-1 Host Operation Mode Functions

14
3.1.3 Hot-keys
Hot-keys are available when utilizing the Sequoia 2H2U under the Host operation mode.
Following are the summarized Host operation mode hot-keys.
Keys
Alt + F#
(F1 –F12)
Use Alt + F1 –F12 function keys (up to F23 with special keyboard) to load
user-created preset files. Sequoia can store 23 user created presets.
Alt + F
Toggle a particular window’s full screen mode on/off.
Note:The window selected is where the Host cursor is currently residing.
Alt + L
Toggle lock/unlock window layout
Ctrl + Esc
This allows Ethernet communication so that you can use the Phoenix-G
(Galaxy) control software and sending of ASCII Z commands.
Ctrl + F#
(F1 –F4)
Loads the particular window to full screen mode, thereby causing other
window(s) to fade from view. Where F# is the source window number
(e.g., Ctrl + F1 will call up the source 1window). In a cascaded system:
First move the Host cursor to the desired module then select the source.
Ctrl + L
Toggle lock/unlock keyboard and mouse. When locked the keyboard and
mouse are inoperable. This is useful for when users are away.
Ctrl + O
Toggle muting the audio output on/off (mute).
Ctrl + P
Toggle a window on and off. Where Pis the source/window number
(e.g., Ctrl + 1will turn on/off the source 1window).
Ctrl + R
Toggles between aspect ratios, for the window that the Host cursor is on.
Settings: 4:3, 16:9 and off.
Ctrl + S
Saves the latest preset to the Sequoia so that on the next boot-up the
latest preset will be loaded.
Note: Also simultaneously saves latest presets for cascaded modules.
Ctrl + X
When a video signal does not fill up the entire frame a black bar fills in the
empty space that is left behind.Pressing Ctrl + Xcrops off the black bars.
When applying this function, make sure the image does not have a black
or dark grey background to avoid cropping off part of the actual image.
Note: Only applicable for HDMI and DVI input signals (SDI not supported)
Ctrl + Y
Redo: redo up to ten previously “undone” actions.
Ctrl + Z
Undo: undo up to ten previous actions.
Ctrl + Shift + Alt + R
Reset the cascaded module’s system configuration only.
F# or Shift + F#
Access a remote computer (F# represents keys F1 or F2). F1
corresponds to the Source 1 window while F2 corresponds to the
Source 3 window. Window swapping can be enabled/disabled from the
Phoenix-G (Galaxy) control software.
When the parameter inside the Phoenix-G(Galaxy) software “Swap with
Active Window” is enabled (under the Sequoia Properties menu) then:
Upon Pressing F#:
The active window and the selected window swap positions.
And selected window enters Remote operation mode.
Upon Pressing Shift + F#:
Selected window enters Remote operation mode (no
swapping).
When the parameter “Swap with Active Window” is disabled then:
Upon Pressing F#:
Selected window enters Remote operation mode (no
swapping).
Upon Pressing Shift + F#:
The active window and the selected window swap positions.
And selected window enters Remote operation mode.
Home
When in full screen mode, toggle between full screen in foreground and
full screen in background.
Page Up/Down
Switch between the 3 factory-default presets.
Shift + I
Switch audio input source between HDMI IN and source ports. Audio tally
(red) signifies that audio output is coming from a particular window.

15
Keys
Shift + L
Toggle priority of overlaying windows on/off –upon clicking a window will
not cause the window to become the topmost window.
Shift + O
Switch the audio output between the Sequoia’s internal speakers and the
HDMI OUT port.
Note: This function is not available when connected to the HDMI OUT
port via a DVI-to-HDMI adapter.
Shift + /
Shift + 
Due to subtle differences in processing times; the audio and video may
need to be re-synced, this is done by adjusting the audio delay. The
Sequoia provides up to 170 milliseconds of audio delay adjustment. Use
(Shift + ) to decrease delay and (Shift + ) to increase delay.
(red LED)
Tab
Move the Host cursor from one display (monitor) to the other (applicable
only during cascading).
/ 
Decrease/increase the volume level (10 levels including mute).
(green LED)

Load the previous user-created preset file.
Note: Use the Phoenix-G (Galaxy) control software to create and save
your own presets.

Load the next user-created preset file.
Table 3-2 Hot-keys of Host Operation Mode
Pressing Ctrl + Esc hot-keys as well as the “Load Preset” action will clear the undo (Ctrl + Z) and
redo (Ctrl + Y) list in memory.
3.2 Remote Operation Mode
3.2.1 Hot-keys
The following hot-keys are only available when utilizing Sequoia 2H2U under Remote operation mode.
Keys
Pause
Break
Exit from the Remote operation mode to the Host operation mode.
Ctrl + Esc
This command allows Ethernet communication so that you can use the
Phoenix-G (Galaxy) control software.
Note:
1. Pressing Ctrl + Esc will also open up the Windows start menu. This is
okay, simply exit the Windows start menu and proceed.
2. To disable “Surfer”feature (next hot-key description), pressing Ctrl +
Esc and then running and quitting Phoenix-G software can accomplish
this. “Surfer”feature will automatically be enabled upon entering “Host
operation mode”and then entering “Remote operation mode.”
Ctrl + Shift + Alt +
F10
Toggles the “Surfer”feature on and off; wherein upon moving mouse to
same border that is shared with another remote computer will cause the
Sequoia’s (Host) keyboard and mouse to control next selected computer.
Note:
1. Not applicable for Sequoia 2H2U with touch-screen display setup or
with PS/2 connection.
2. Not applicable after pressing the above-mentioned Ctrl + Esc hot-key
and then running and quitting Phoenix-G software. “Surfer”feature will
automatically be enabled upon entering “Host Operation Mode”and then
entering “Remote operation mode.”
3. Refer to Appendix A for more details.