Avocent DSR Series DSR1030 User manual

The following instructions will help you
to connect your DSR switch.
Should you require further assistance, please
consult your installer/user guide.
The Power of Being There
To connect a DSR switch
Quick Installation Guide
DSR®Switch
DSR1030 | DSR2030 | DSR4030 | DSR8030 Switches
Connecting power to the
DSR switch
Power down all servers that will be part of your DSR
switching system. Locate the power cord that came
with the DSR switch. Plug one end into the power
socket on the rear of the DSR switch. Plug the other
end into an appropriate AC wall outlet.
Connecting the local port
Plug your VGA monitor, PS/2 or USB keyboard and
mouse cables into the appropriately labeled DSR
switch ports.
Connecting a DSRIQ module to
the DSR switch
Choose an available port on the rear of your DSR
switch. Plug one end of a CAT 5 cable (4-pair, up to
10 meters) into a numbered port and plug the other
end into the RJ-45 connector of a DSRIQ module.
Connecting a server to the
DSRIQ module
Plug the DSRIQ module into the appropriate ports on
the back of the server. Repeat this procedure for all
servers that are to be connected to the DSR switch.
Connecting network and
remote users
Plug a CAT 5 cable from your Ethernet network into
the LAN connector on the back of your DSR switch.
Network users will gain access through this port.
Plug in the
keyboard, monitor
and mouse for your
local connection.
Server
Local Connections
Server
Modem
Connect the
switch to the
network.
Connect DSRIQ
modules to the
DSR switch.
Connect servers to
the DSRIQ modules.
Power down all
servers and
attach the
appropriate
power cord to
the DSR switch.
Plug in the
external modem
(optional).
Server
Server
Connecting an external
modem (optional)
The DSR switch may also be accessed using an ITU
V.92, V.90 or V.34-compatible modem. Plug one end of
a 9-pin serial cable into the MODEM connector on the
back of your DSR switch. Plug the other end into the
appropriate connector on the back of the modem.
NOTE: Using a modem connection instead of a LAN
connection will limit the performance capability of your
DSR switch.
(continued on reverse side)
1357
2468
91113
10 12 14
15
16
DSR Switch
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. © 2005 Avocent Corporation. All rights reserved. 590-473-603A
Telephone
network
Ethernet

1357
2468
91113
10 12 14
15
16
The following instructions will help you
to connect your DSR switch.
Should you require further assistance, please
consult your installer/user guide.
Connecting the SPC device to the
DSR switch (optional)
Plug one end of the cable supplied with the SPC
power control device into the SPC port on the DSR
switch and plug the other end into the SPC device.
Plug the power cords from the target servers into the
SPC power outlets. Plug the SPC device into an
appropriate AC wall outlet.
Powering up targets and switch
Power up each target server and then power up the
DSR switch.
Connecting local virtual media
(optional)
Connect virtual media devices to any of the five USB
ports on the DSR switch.
NOTE: To open a virtual media session with a
server, the server must first be connected to the
switch using a virtual-media capable DSRIQ
module (USB2 or USB2L).
For additional information
For further instructions on DSR switch connection,
software setup and security configuration, please
refer to the installer/user guide included with the
switch. Check http://register.avocent.com for the
latest DSR switch software and firmware updates.
The Power of Being There
To connect a DSR switch
(continued from reverse side)
Quick Installation Guide
DSR®Switch
DSR1030 | DSR2030 | DSR4030 | DSR8030 Switches
Server
DSR Switch
SPC Power
Control Device
Server
Server
Server
Connect your
SPC device to
the target servers
(optional).
Power up target
servers and then
the DSR switch.
Plug in virtual media
devices to the USB
ports (optional).
or
External Virtual
Media Device
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. © 2005 Avocent Corporation. All rights reserved.
A1

The Power of Being There
1357
2468
91113
10 12 14
15
16

1357
2468
91113
10 12 14
15
16
The Power of Being There
A1

The Power of Being There
1357
2468
91113
10 12 14
15
16

1357
2468
91113
10 12 14
15
16
The Power of Being There
A1

The Power of Being There
1357
2468
91113
10 12 14
15
16

1357
2468
91113
10 12 14
15
16
The Power of Being There
A1