Avtech KPC131D User manual

308Z
KPC131D_135D_V1.0
USER MANUAL
Regular Camera Series
The product image may differ from the actual product.
Please read the instructions thoroughly before using the product.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
ROHS Announcement
All lead-free products offered by the company comply with the requirements of the European law
on the Restriction of Hazardous Substances (RoHS) directive, which means our manufacture
processes and products are strictly “lead-free” and without the hazardous substances cited in the
directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be
collected seperately at the product end-of-life. This applies to your product and any peripherals
marked with this symbol. Do not dispose of these products as unsorted municipal waste.
CE Mark
This apparatus is manufactured to comply with the radio interference.
The company does not warrant that this manual will be uninterrupted or error-free. We reserve the
right to revise or remove any content in this manual at any time.
C
CA AU UT TI IO ON N: :
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we have been
advised of the possibility of such damages.
C
C
A
A
U
U
T
T
I
I
O
O
N
N
R
RI IS SK K O OF F E EL LE EC CT TR RI IC C S SH HO OC CK K

OVERVIEW
Equipped with a 1/3” Color CCD image sensor, this regular camera possesses
satisfactory minimum illumination to provide clear and sharp images and has a
microphone built-in to consolidate the quality of your surveillance system.
FEATURES
1. High quality picture
2. Satisfactory minimum illumination of 0.05 Lux/F2.0
3. Audio function supported
4. Auto Electronic Shutter built-in
5. Signal-to-noise ration of 48dB
SPECIFICATIONS*
M
MO OD DE EL L M
Mo od de el l 1 1 M Mo od de el l 2 2
Pick up Element 1/3" Color CCD image sensor
Number of Pixel 512(H) x 492(V) <NTSC> / 512(H) x 582(V) <PAL>
Resolution Standard
Min. Illumination 0.05 Lux / F2.0
S/N Ratio More than 48dB (AGC off)
Electronic Shutter 1/60 (1/50) to 1/100,000 sec.
Lens Mount CS mount
IRIS Mode D.D./ V.D./ AES
AGC Auto
White Balance ATW
Video Output 1.0 Vp-p composite, 75Ω
Microphone YES
Power Source (±10%) DC12V AC230V AC24V / DC12V
Current Consumption (±10%) 80mA
Dimensions (mm)** 108(L) x 62(W) x 50(H)
* The specifications are subject to change without notice.
** Dimensional Tolerance: ± 5mm
PACKAGE CONTENT
‧ Camera x 1
‧ User manual x 1
‧ Wrench x 1

* The CS-C conversion ring is not supplied in the sales package and needs to be purchased separately.
MAJOR OPERATING CONTROL AND FUNCTIONS
VIDEO AUDIO
V.D. D.D.
AES AI
PL
LEVEL
L H
2
2
AU TO IRI S
11
4
4
33
12V DC
DC12V
VIDEO AUDIO
V.D. D.D.
AES AI
PL
LEVEL
L H
AC 230V 22
11
44
33
AU TO IRI S
VIDEO AUDIO
V.D. D.D.
AES AI
PL
LEVEL
L H
22
11
44
33
AC 24V
DC 12V
AU TO IRI S
AC230V AC24V / DC12V
1. Flange Back Adjusting Ring
It is suitable for CS-mount lens. When using C-mount lens, please use the CS-C conversion ring*.
2. Back Focal Lock Hexagonal Bolt
The camera is set at the standard back focal position. Fine-tuning is inevitable according to the lens types.
Adjust the lens back-focus by turning the focusing knob.
3. Auto Iris Lens Connector
Supplies power and controls signals to an Auto Iris Lens.
Connect to the auto iris lens cable with the supplied iris connector (4-pin male connector).
4. DC Drive Level adjustment V.R.
When using Direct Drive Lens, you can adjust the DC Drive Level for the bright of video output.
5. Power LED Indicator
The Power LED Indicator indicates normal status during operation.
6. Power Input Terminal !
 For connecting to DC12V regulated power supply.
 For connecting to the regulated AC230V power supply.
 For connecting to DC12V / AC24V regulated power supply.
* : For connecting with the ground (earth) of power supply cable.
7. Video Output Connector (VIDEO OUT)
For connecting to CCTV monitor video input with coaxial cable.
8. Function Select
 AES (Automatic Electronic Shutter) / AI (Auto Iris Lens) selectable:
AES – When using a manual iris lens or fixed iris lens, set this switch to AES.
AI – When using an auto iris lens, set this switch to AI.
9. V.D. / D.D. selectable
When using Auto Iris Lens, select Video Drive or Direct Drive depend on the type of lens you used.
10. Audio Output Connector (AUDIO OUT)
Connect to the AUDIO IN connector of the recording device.

* The CS-C conversion ring is not supplied in the sales package and needs to be purchased separately.
INSTALLATION
***The following installation is better accomplished by qualified service personnel or system installer.***
1. Mount a lens onto the camera (By turning it clockwise).
It is suitable for CS-mount lens.
But if the lens you chose is C-mount, please use the CS-C conversion ring* to connect the C-mount lens
and the camera.
2. Switch the lens selection depending on the lens you used.
* Manual iris lens or fixed lens:
AES: When using manual iris lens or fixed iris lens, set switch to AES.
* Auto iris lens:
AI: When using auto iris lens, set switch to AI.
V.D. / D.D.: When using Auto Iris Lens, select VD or DD depend on the type of lens you used.
3. Connect the camera VIDEO output and the monitor video input with a 75Ωcoaxial cable.
4. Connect the camera AUDIO output and the monitor audio input with a coaxial cable.
5. Connect the POWER terminal of the camera to a right power supply.
6. Adjust the focus or flange-back (Please refer to N NO OT TE E for adjustment instructions).
NOTE: Focus or Flange-Back Ring Adjustment
1. Mount the lens
by turning it clockwise on the lens mount of the camera.
2. Loosen the screws on the flange-back adjusting ring.
3. Turn the flange-back adjusting ring to the desired position.
4. Tighten the screws on the flange-back adjusting ring.
PRECAUTIONS
 Do not install the camera in an environment where the humidity or temperature is high
 Do not install the camera under the unstable lighting condition
 Do not expose the camera to rain or moisture
 Do not keep the camera face to strong light directly
 Do not touch the front glass of the camera
 Do not use other than specified power source
 Do not disassemble the camera